1.Calculate the Concrete Mix Design for M35 grade concrete with fly ash.    Aim:           To calculate the concrete mix design for M35 grade concrete with fly ash as given below.   Introduction:          concrete mix design is the process of finding right proportions of cement,sand and aggregate for concrete to achieve…

Sketch a G+1 floor residential plan, according to Vaastu Shastra, and list down the names of the structural drawings required to be provided to the site for construction.   Aim:       To sketch a G+1 floor residential plan ,according to vaastu shastra and the names of the structural drawings…

Create the geometries from P1 to P2 using all the coordinates system methods. You need to use the Line tool to create the geometries. Where required you need to use the circle tool.Please read the drawings and find out the missing dimensions before working on the sketches.   Aim: (A)Create the geometries from P1 to…

AIM: To Draw c.s of load bearing wall over spread footing using autocad software PROCEDURE: Open Autocad  In the command prompt type QNEW Click on imperical template, advaced setup, decimal In the command prompt type (rectangle) specify first corner point (1,1) In the command prompt click dimensions specify length…

AIM: To draw the above figuure using autocad  PROCEDURE: Line command  starting point (0,0) Form 3.0 unit left after that move 2.1 at an angle 45 degrees to (2.1<45) Then 2.8 at an angle of 90 degrees inside  2.0m on left side  close  else  type ptype command and select point  mark…

AIM: To create a residence layout plan using autocad. INTRODUCTION: The main objective of this challenge is to get in touch with various tools in autocad like rectangle , polyline , circle ,arc modification tools like copy,move,offset,mirror,trim,fillet.these tools will be understood by creating a residence layout,…

1. AIM: To create a column schedular as shown in figure PROCEDURE: In the command prompt type line to create tables In the command prompt type ST (text style)> Arial.shx (font name) > 8" (height) > left (justify) In the command prompt type text to text the given text in the drawing In the command prompt type MTEXT…

AIM: To draw the elevation and details of a wardrobe as shown in the figure. After sketching, you need to provide the dimensions and text with the use of layers. PROCEDURE: STEP 1: Units are set to mm Limits and limax are also set Zoom command is also used STEP 2: In the command line type rec > 2800,2600 In the command…

Aim :- To draw the Plan, Elevation and Section of the building by using AutoCAD Software        Introduction :- The general commands used for drawing the building is as follows : Line Polygon Rectangle Circle Erase Copy Trim Mirror Offset Extend Move The dimensions: For external wall – 250mm…

1.AIM : To draw the Floor Plan. Elevation and section of Residential Buildings using the various commands in Auto CAD.  PROCEDURE : To create a new drawing sheet. Type ,,UN' to set the units of current format of measure.( FEET and INCHES) Type LIMITS' to set the maximum dimension limits on the particular page. To draw…

AIM: To create template with inserting text and attributes and required objects by using Auto CAD INTRODUCTION: XLine: It means construction line. It has infinty edges we used for making wall. By typing "XL" on command line we envoke this tool.  Line: It connects one point to another points. Used to draft…

AIM: To create the layout of the kitchen and providing hatches to it using the autocad in detail. INTRODUCTION: kitchen layout is the most important part of designing your perfect kitchen. It's the layout that will determine how you cook, how you eat and how you socialise. So whether you're totally remodelling the kitchen,…

AIM: To create layout of the plan and section A of the project in challenge7 as shown in the figure INTRODUCTION: The layout is created in AutoCAD by using the template Tutorial-mArch.dwt in a given scale PROCEDURE:   Open week 7 challenge in AutoCAD Zoom the Plan which is cover entire screen…

AIM  To create a 3D Furniture elements using the various commands in Auto CAD. INTRODUCTION BY 3D VIEW The process of creating a mathematical representation of any surface of an object in three dimensions by using special software. A 3D model can even be represented as a two dimensional image by using the 3D  rendering…

AIM To create a 3D Isometric view of the given building with plan and elevation INTRODUCTION As isometric drawing is 30 representations of an object, room, building or design on a 2D surface. One of the defining characteristics of an isometric drawing. compared to other types of 30 representation, is that the final image…

Aim: To create the 3D rendered model for a Residential Building in AutoCAD. Introduction: The 3D view of a wall spread footing is created in AutoCAD in 3D Modelling workspace using primarily the line and Extrude tools. The procedure of drawing is explained in detail with diagrams of each step and the final result is given.…

  1.From the file menu, create a new project (Structural / Architectural / Construction template ) and name the project appropriately  Aim: To create a new project. To name the project appropriately. Procedure: To create a project template. After opening the revit software we will have a display thea contains…

1.AIM:  To model a ceiling from the architectural tab above the walls at the first-floor level INTRODUCTION: Ceilings help create an enclosure and separation between spaces, they help to control the diffusion of light and sound around a room and help prevent the passage of sound between rooms. In Revit, The creation…

1)Select the type of structure you want to build from one of the three below: Multi-Unit Residential Apartment Office Buildings School Multi-Unit Residential Apartment    2)Assume reasonable assumptions for geographic and location details for your project modelling. Based on assumptions and type of structure…

  1. Aim: TO create a sinusoidal points curve and surface using dynamo  Procedure: Go to select new template> select architecture temoplate> press ok Go to the manage tab and select Dynamo open integer slider Add Code block and math. sin for parametric point Used product Add NURBS curve by control point for curve and list…

  1.Aim:   Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Introduction: Use Navisworks project review software to improve BIM (Building Information Modelling) coordination. Combine design and construction data into a single model. Identify and resolve clash and interference problems before…

QUESTION 1 What is the mode of failure or damage of the beams in the figure above? Are the damages repairable? Elaborate  ANSWER 1 a)             This crack will be formed due to the flexural of a beam The flexural strength, known as modulus of rupture, bend strength, or fracture strength,…

1. Differentiate Static analysis and Dynamic analysis with proper representing pictures   The nature of loading governs the kind of analysis to be performed on the structure. The loads are divided into two basic categories Static Loads are the loads, the variation of load with respective time is very slowly (the…

Understanding the concepts on Degrees of Freedom   Q] A five storey structure with 5 translational DOF is shown here. Each storey has mass ‘m’. The eigenvalue problem has been solved and the 5 periods of vibration Tn and their corresponding mode shapes, φn has been derived. The fundamental period of vibration (T1 = 2 seconds)…

  1.Aim:  To look into aspects of symmetry, redundancy and bi-directional stiffness and ductility. of the framing plan concerning earthquake resistance in the two horizontal directions X or Y. Investigation of the framing plan W.R.T symmetric in the x- direction If we split the plan vertically half it will look mirrored…

1) The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional area of the shear walls. Compare the three alternatives, taking into account the restraint of…

Q) Model a 25 storey building on ETABS 2018 with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey height of 3 metres. Structural Element Sizes  Beams : 300 × 400 mm  Columns : 800 × 800 mm  Slab…

AIM: TO MODEL AND ANALYZE MULTIPLE BUILDINGS WITH DIFFERENT FLOOR LEVELS AND DESIGN PARAMETERS USING ETABS SOFTWARE AND COMPARE THE RESULTS TO UNDERSTAND THEIR OVERALL SEISMIC BEHAVIOUR.     INTRODUCTION:                            The structural configuration of the building plays a major role in determining the overall…

Aim: To design the beams in detail from the ETABS. To provide details of longitudinal and shear reinforcement for the given two continuous beams. To calculate the value of maximum shear force in any one of the spans in the continuous beams. Introduction: Beams are horizontal structural elements used for the supporting…