CREATING 1D ELEMENTS ON GIVEN COMPONENT WITH GIVEN CROSS-SECTION AND DOF   Objective…

GENERATE THE MIDSURFACE AND MESHING THE HOOD COMPONENT:   OBJECTIVE: TO mesh the hood component by generating a midsurface with suitable thickness and given criteria.   ABSTRACT: An automobile's engine hood is important. It performs several functions, for example, during maintenance of engine area, the hood mechanisms…

                                                                                           …

                                                                                    CONNECTIONS REPRESENTATION…

                                                                                           …

MID SURFACE EXTRACTION AND MESHING FOR BACKDOOR MODEL USING HYPERMESH   NOTE: I HAVE ENCLOSED THE MODEL HERE BUT OUTER AND LOWER BODY MESH WAS ENCLOSED ONLY HALF PORTION DUE TO EXCEEDS OF NODE LIMIT. IF WE REFLECT IT WILL GET THE WHOLE MODEL.   Aim : To extract the mid-surface and the mesh the Backdoor…

MORPH THE GIVEN MODEL AND CREATING MACRO OBJECTIVE: MORPH The given side body component to the desired shape shown in the images below and write a MACRO  for the same. Refer the following images for Morphing the model.     PROCEDURE: 1. Morphing the given side body to the desire shape open…

PERFORMINF THE MESH ON THE PASSENGER VEHICLE SIDE DOOR PLASTIC TRIM   OBJECTIVE: To Perform the Mesh on the passenger vehicle side door plastic trim using Hypermesh. ABSTRACT: Abstract: Vehicle interiors are primary source of injuries when occupants interact with them in the event of an accident. The extent of injuries…

OBJECTIVE: To extract a mid-surface of the sheet metal component and to perform 2D meshing on the extracted Mid-surface wit given quality criteria. PROCEDURE: To mesh the given component with quality criteria the below steps should be followed.      1.Import the given geometry in to hypermesh.…

OBJECTIVE:  For the given component, check for the geometrical errors and mesh with the given element Quality criteria. After meshing the component the thickness has to be assigned. QUALITY CRITERIA GIVEN: S.No  Quality Criteria  Value  1 Target/Average length   5 2 Minimum Length …

AIM: For the given component, check for the geometrical errors and mesh with the given element Quality criteria. After meshing the component the thickness has to be assigned.    PROCEDURE: The following steps are used to perform mesh on the geometry. Import the Geometry.   Cleanup the Geometry.…

3D MESHING ON THE REAR-VIEW MIRROR USING - ANSA AIM: To check for the geometrical errors and mesh with the given element Quality criteria. Use tetra elements to model the component and there should not and kinks and dips on the surface of the component. PROCEDURE: IMPORT THE GIVEN MODEL   CHECK FOR GEOMETRICAL…

AIM: The connection of the front door is shown in detail and the different types of connection techniques along with different 1D elements  PROCEDURE: IMPORT THE GIVEN MODEL   CHOOSE THE SUITABLE CONNECTIONS IMPORT THE GIVEN MODEL: Import the given model from ANSA FILE-INPUT-NASTRAN-CHOOSE FILE    …

AIM: In this challenge we practice all the Basic Morphing techniques and write the report on Morphing and its uses in various industries. PROCEDURE: IMPORT THE GIVEN GEOMETRY   CLEANUP THE GEOMETRY   MORPHING IMPORT GIVEN GEOMETRY: Import the given geometry COMMAND: FILE-INPUT-OPEN-CHOOSE      …

AIM: For the given component, check for the geometrical errors and mesh with the given element Quality criteria. After meshing the component the thickness has to be assigned. S.No  Quality Criteria  Value  1 Target/Average length   4 2 Minimum Length  2 3 Maximum Length  6 4 Aspect …

AIM: Convert the given measurements into different system of units and finding their corresponding conversation factors OBJECTIVE: CALCULATE THE CONVERSION FROM SI UNITS TO gm/mm/ms unit system REST OF THE VALUES PLOT ON THE TABLE FROM SI UNIT TO  REQUIRED UNIT VALUES MEASUREMENTS GIVEN: MASS 1kgLENGTH 1mTIME…

AIM: To solve using both Explicit and Implicit Methods for the Given Equation F(u) = `u^3+9u^2+4u`. have a tolerence of `10^-2` EXPLICT AND IMPLICT ANALYSIS There are two types of approach here IMPLICT & EXPLICT, this used to solve the Finite element analysis problems. Implicit and Explicit…

OBECTIVE: IMPORT THE GIVEN GEOMETRY CLEANUP THE GEOMETRY GENERATE MIDSURFACE FOR REQUIRED COMPONENTS GENERATE VOLUME MESH FOR HOLLOW COMPONENTS IMPROVE THE MESH FLOW WITH PROPER FEATURE CAPTURING GIVE CONNECTIONS FOR THE SUSPENSION ASSEMBLY ABSTRACT: For this project check for the geometrical errors and mesh with the given…