1. Here they asked me to build a door bell with a following condition i.e. the switch should closed for every 2sec and then released. so, here i used a pulse generator to generate a signal as per the given condition. and here as i am using a switch and the signal is directly given to the switch we are using 'simulink-ps…

1. here they asked me to Implement control logic of a washing machine using Stateflow as per given sequence or conditions If the power supply is available, the system gets activated  If the Water supply is not available, stop the process & indicate through LED Soaking time should be 200s followed by Washing…

In this first question they asked me to take EV_defaults_in file in the advisor tool. * And they asked me to change the cargo mass to 500kg   And then I changed as they asked me to do * I also taken the cycle as FTP (Federal Test Procedure) At first I had taken no.of cycles is 3 in the simulation parameters…

1.   Here, When you customize a SI or CI reference application, you can use either a  dynamic or mapped engine model. So, lets first see about the implementation of mapped engine models While implementing the mapped type of engine Model uses a set of steady-state lookup tables to characterize engine performance.…

 1.   All-electric vehicles (EVs), also referred to as battery electric vehicles, use a battery pack to store the electrical energy that powers the motor. EV batteries are charged by plugging the vehicle in to an electric power source. So, for this charging and usage there will be a need of power converting at…

1. here they asked me to explain the MATLAB demo model named ‘Speed control of a DC motor using BJT H-bridge so, i had opend the model in  the simulink   In the above Circuit the Input voltage is generated from the Pulse generator where the amount of supply and duty cycle is assigned in the Pulse generator…

1. here they asked me to calculate the energy required for braking. so, now i had created a new driving cycle with the values of time in seconds and the velocity in mt/sec. and after assigned those values i had calculated the braking energy in joules and after i had coverted the calculated energy (joules) into energy(KWh)…

1. Main Objective : * To create a simulink model of an Electric Vehicle by using battery and motor modules * To run the model and to check the performance of the model and its parameters * To observe the results and to notedown Here is the basic thing of an Electric vehicle and its construction and modeling …

1. lithium-ion (Li-ion) battery : A lithium-ion (Li-ion) battery is an advanced battery technology that uses lithium ions as a key component of its electrochemistry. During a discharge cycle, lithium atoms in the anode are ionized and separated from their electrons. The lithium ions move from the anode and pass through…

1. here they asked me to simulate the three test cases of the harness dashboard and to run the simulation and to observe the output of those test sequence so, here to get the closed loop harness we should have Battery management system file we can get that file from the MATLAB help section or we can also get that file…

Aim : To prepare the detailed battery pack drawingalong with its enclosure and to calculate the necessary perameters Here they asked me to prepare a detailed battery pack drawing along with its enclosure of the ANR26650M1-B So for this we need the specification of the particular battery which is available in its data sheet…

Mini Project - Vehicle Direction Determination General Overview: Identifying the direction of the vehicle is one of the important & diverse features in Autonomous driving & Advanced Driver Assistance Features. This particular sub-feature of identifying the direction of vehicle is basically identifying the direction…

Obhective : To create a model for a 10 cell series lithium ion battery model, simulate the thermal effects and compare life cycle performance at various temperatures, charge & discharge rates using MATLAB. The standard rating for batteries is at room temperature 25 degrees C (about 77 F). At approximately -22…

1. When looking at different aircraft's specifications or in POHs/AFMs, there are several different weights of the aircraft mentioned (e.g. maximum take-off weight, maximum landing weight, operating empty weight) The different terms represent different weights or masses1. For each flight, the weights are taken into account…

Aim : Developing Adaptive Cruise Control feature as per the Requirement Document using MATLAB Simulink. To generate the C Code for the designed model. Here is the general overview about the Adaptive Cruise Control General Overview (Adaptive Cruise Control (ACC) : Adaptive Cruise Control Feature for passenger cars allows…