GATE 2027 Instrumentation syllabus: what changed, and what was actually asked
The GATE 2027 Instrumentation syllabus is heavily revised: the same ten sections, but 21 new lines, 23 expanded ones and three-phase induction motors gone. 20 of the new lines have never been asked in GATE IN. Below is every line in IIT Madras's wording, marked where it changed, with how often the 5 papers from 2022 to 2026 asked it.
Source: IN_GATE2027_Syllabus.pdf (IIT Madras) and IN_2026_Syllabus.pdf (IIT Guwahati) · 275 technical questions from GATE IN 2022 to 2026 · Updated 19 Nov 2026
What changed in the GATE 2027 Instrumentation syllabus?
IIT Madras revised the IN syllabus for GATE 2027. The ten sections keep their names, but 21 lines are new, 23 are expanded and several topics moved between sections. Out: three-phase induction motors and the named transformer tests, mean value theorems, nonlinear first-order equations, synchros and hydraulic or pneumatic components, sizing of control valves and open-channel flow meters. In: permanent magnet synchronous machines, buck and boost converters, inverters and PWM control; Maxwell's equations, dipoles and the B-H curve; finite state machines, embedded programming and AI applications in instrumentation; the digital energy meter and spectrum analyzer; near-infrared sensing; tensors and backpropagation. Moved: comparators and Schmitt triggers to Analog Electronics, PLC and DCS to Control Systems, the 4-20 mA transmitter to Communication, shielding and grounding to Analog Electronics, sampling and Fourier series to Signals and Systems. 20 of the 21 new lines have no GATE IN question from 2022 to 2026 to practise from.
| Syllabus line in 2027 | Section | Change | Asked 2022-26 |
|---|---|---|---|
| Tensors | Engineering Mathematics | New | none |
| Functions, limits, continuity and differentiability | Engineering Mathematics | New | 3 Q |
| Conditional probability and Bayes' theorem2026: “conditional probability” | Engineering Mathematics | 3 Q | |
| Backpropagation for neural networks | Engineering Mathematics | New | none |
| Dielectrics, permittivity and capacitance2026: “Capacitance of simple configurations” | Electricity and Magnetism | 2 Q | |
| Magnetic field intensity and flux density | Electricity and Magnetism | New | none |
| Permeability, self and mutual inductance2026: “Self and Mutual inductance of simple configurations” | Electricity and Magnetism | none | |
| Electric and magnetic dipoles | Electricity and Magnetism | New | none |
| Electromagnetic induction | Electricity and Magnetism | New | none |
| B-H curve | Electricity and Magnetism | New | none |
| Maxwell's equations | Electricity and Magnetism | New | none |
| V-I characteristics: sources, battery, solar cell, R, L, coupled L, C2026: “v-i relationships of resistor, inductor, mutual inductance and capacitor” | Electrical Circuits and Machines | 3 Q | |
| Transients in RC, RL, LC and RLC circuits2026: “transient analysis of RLC circuits with dc excitation” | Electrical Circuits and Machines | 3 Q | |
| Power, energy, component ratings, efficiency and losses | Electrical Circuits and Machines | New | none |
| Kirchhoff's laws, mesh and nodal analysis, star-delta2026: “Kirchoff's laws, mesh and nodal analysis” | Electrical Circuits and Machines | 1 Q | |
| Superposition, Thevenin, Norton, Miller, maximum power transfer, reciprocity2026: “superposition, Thevenin, Norton, maximum power transfer and reciprocity theorems” | Electrical Circuits and Machines | 3 Q | |
| One-port and two-port networks, open and short circuit parameters2026: “One-port and two-port networks” | Electrical Circuits and Machines | 1 Q | |
| Permanent magnet synchronous machines | Electrical Circuits and Machines | New | none |
| Buck and boost converters, rectifiers, single-phase inverters | Electrical Circuits and Machines | New | none |
| Rotor position, speed and current sensing; PWM control | Electrical Circuits and Machines | New | none |
| Feedback principles and the role of sensing2026: “Feedback principles” | Control Systems | none | |
| Supervisory control, DCS and PLC2026: “basics of distributed control systems (DCS) and programmable logic controllers (PLC)” | Control Systems | none | |
| BJT and MOSFET circuits: biasing, DC analysis, power dissipation2026: “BJT and MOSFET” | Analog Electronics | 4 Q | |
| Small-signal analysis and frequency response2026: “small signal analysis of transistor circuits” | Analog Electronics | 4 Q | |
| Noise and interference: coupling, thermal, shot and flicker noise2026: “sources and effects of noise and interference in electronic circuits” | Analog Electronics | 1 Q | |
| Component selection, circuit board realization and testing | Analog Electronics | New | none |
| Combinational logic, multiplexers, truth tables2026: “Combinational logic circuits” | Digital Electronics | 4 Q | |
| IC families (ECL, TTL, CMOS) and CMOS logic gates2026: “IC families: TTL and CMOS.” | Digital Electronics | 2 Q | |
| Finite state machines | Digital Electronics | New | none |
| Analog front end: analog multiplexer, PGA, sample-and-hold2026: “sample-and-hold circuit, multiplexer” | Digital Electronics | 1 Q | |
| ADC and DAC specifications: resolution, quantization, INL, DNL, ENOB2026: “Characteristics of ADC and DAC (resolution, quantization, significant bits, conversion/settling time)” | Digital Electronics | 3 Q | |
| Embedded systems programming | Digital Electronics | New | none |
| Data acquisition, virtual instrumentation and IoT2026: “basics of data acquisition systems” | Digital Electronics | none | |
| AI in instrumentation: linearization, calibration, signal classification | Digital Electronics | New | none |
| Voltage, current and power in DC, single and three-phase AC2026: “Measurement of voltage, current and power in single and three phase circuits” | Measurements | 5 Q | |
| Contact and non-contact current and voltage probes2026: “ac and dc current probes” | Measurements | 1 Q | |
| Digital energy meter | Measurements | New | none |
| Digital storage oscilloscope2026: “oscilloscope” | Measurements | none | |
| Spectrum analyzer | Measurements | New | none |
| Electromagnetic and Hall effect sensors2026: “Hall effect sensors” | Sensors and Industrial Instrumentation | 2 Q | |
| Pressure, including low and high pressure2026: “pressure (including low pressure)” | Sensors and Industrial Instrumentation | 1 Q | |
| Transmitter and receiver architectures | Communication and Optical Instrumentation | New | none |
| Instrument and sensor networks | Communication and Optical Instrumentation | New | none |
| Near-infrared sensing | Communication and Optical Instrumentation | New | none |
Dropped from the 2026 wording: “Mean value theorems” (Engineering Mathematics). Integration stays; no GATE IN question from 2022 to 2026 was a mean value theorem question. “First order equation (linear and nonlinear)” (Engineering Mathematics). 2027 keeps first-order linear equations only. “Divergence” (Electricity and Magnetism). Gauss' law and Maxwell's equations in differential form stay, so divergence still turns up inside them. “Curl” (Electricity and Magnetism). Same as divergence: Maxwell's equations in differential form still use it. “Three phase induction motors: principle of operation, types, performance, torque-speed characteristics, no-load and blocked rotor tests, equivalent circuit, starting and speed control” (Electrical Circuits and Machines). The biggest cut: replaced by permanent magnet synchronous machines, buck and boost converters, rectifiers and inverters. “Equivalent circuit, phasor diagram, open circuit and short circuit tests, regulation and efficiency” (Electrical Circuits and Machines). Single phase transformers stay, without the named tests. “Types of losses and efficiency calculations of electric machines” (Electrical Circuits and Machines). Efficiency and losses now sit with power and energy in the circuits part. “mechanical, hydraulic and pneumatic system components, synchro pair” (Control Systems). Actuators are now control valves, servo valves, servo motors and stepper motors. “sizing of control valves” (Control Systems). “open channel flow meters” (Sensors and Industrial Instrumentation).
Compared word by word against the GATE 2026 IN PDF. Rewordings and moves between sections (for example comparators from Digital to Analog Electronics) are marked on the item below; spelling and capitalisation fixes are not listed.
Which new GATE 2027 IN topics have no previous-year questions?
20 new lines have no GATE IN question from 2022 to 2026: tensors, backpropagation for neural networks, magnetic field intensity and flux density, electric and magnetic dipoles, electromagnetic induction, B-H curve, Maxwell's equations, power, energy, component ratings, efficiency and losses, permanent magnet synchronous machines, buck and boost converters, rectifiers, single-phase inverters, rotor position, speed and current sensing; PWM control, component selection, circuit board realization and testing, finite state machines, embedded systems programming, AI in instrumentation: linearization, calibration, signal classification, digital energy meter, spectrum analyzer, transmitter and receiver architectures, instrument and sensor networks and near-infrared sensing. With no IN papers to practise from, read a standard textbook chapter for each and expect one- and two-mark conceptual questions first. The closest past questions:
- Permanent magnet synchronous machines: the transformer questions and the three induction-motor questions (slip, torque, speed) that the new line replaces on GATE IN Electrical Circuits and Machines PYQs.
- Buck and boost converters, rectifiers, single-phase inverters: the diode switching, rectifying and Zener-regulator questions on GATE IN Analog Electronics PYQs.
- Maxwell's equations: the Gauss' law and Faraday's law questions, which are two of the four equations in integral form on GATE IN Electricity and Magnetism PYQs.
- AI in instrumentation: linearization, calibration, signal classification: the linear regression and error questions (sensor linearization and calibration are curve fitting at heart) on GATE IN Measurements PYQs.
The other new line is new only in the syllabus, not in the papers. Earlier GATE IN papers already asked it, so the past questions are a fair guide:
- Functions, limits, continuity and differentiability: 3 questions (2023, 2026), e.g. Is f(x) = x|x| continuous and differentiable at x = 0?
Which GATE IN syllabus topics are asked the most?
Across the 5 GATE IN papers from 2022 to 2026, the syllabus items with the most marks were AC and DC bridges: Wheatstone, Kelvin, Maxwell, Anderson, Schering, Wien (14 marks, 9 questions), op-amp adder, subtractor, integrator, differentiator, difference and instrumentation amplifiers (12 marks, 7 questions), Laplace, Fourier and z-transforms (11 marks, 6 questions), resistive sensors and their signal conditioning (11 marks, 6 questions) and optical sources and detectors: LED, laser, photodiode, LDR (9 marks, 6 questions). Asked in every one of the 5 papers: AC and DC bridges: Wheatstone, Kelvin, Maxwell, Anderson, Schering, Wien, op-amp adder, subtractor, integrator, differentiator, difference and instrumentation amplifiers, resistive sensors and their signal conditioning and matrix algebra, linear equations, consistency and rank.
| Syllabus item | Section | Questions | Marks | Years asked |
|---|---|---|---|---|
| AC and DC bridges: Wheatstone, Kelvin, Maxwell, Anderson, Schering, Wien | Measurements | 9 | 14 | 2022, 2023, 2024, 2025, 2026 |
| Op-amp adder, subtractor, integrator, differentiator, difference and instrumentation amplifiers | Analog Electronics | 7 | 12 | 2022, 2023, 2024, 2025, 2026 |
| Laplace, Fourier and z-transforms | Signals and Systems | 6 | 11 | 2022, 2023, 2024 |
| Resistive sensors and their signal conditioning | Sensors and Industrial Instrumentation | 6 | 11 | 2022, 2023, 2024, 2025, 2026 |
| Optical sources and detectors: LED, laser, photodiode, LDR | Communication and Optical Instrumentation | 6 | 9 | 2022, 2023, 2026 |
| Temperature: thermocouple, RTD, thermistor, pyrometer | Sensors and Industrial Instrumentation | 6 | 9 | 2022, 2024, 2025, 2026 |
| Single-phase transformers | Electrical Circuits and Machines | 5 | 9 | 2023, 2024, 2025, 2026 |
| Capacitive sensors | Sensors and Industrial Instrumentation | 5 | 8 | 2023, 2024, 2025, 2026 |
| Voltage, current and power in DC, single and three-phase AC | Measurements | 5 | 8 | 2022, 2023, 2025 |
| Bode plot, phase and gain margins | Control Systems | 4 | 8 | 2022, 2023, 2026 |
Counted by Skill-Lync: each question of GATE IN 2022 to 2026 filed under the one syllabus item it mainly tests; marks from the official answer keys.
Which GATE IN syllabus topics were not asked from 2022 to 2026?
31 of the items that were already in the syllabus before 2027 were not the point of any question in the 5 papers, among them numerical integration, partial differential equations, PID tuning, PLC and DCS, the Q-meter, oscilloscopes and digital modulation; the full list is below. That is a reason to give them less time, not to skip them: the syllabus is the contract, and with a revised syllabus the 2027 paper setters may well test what is new.
- Engineering Mathematics: vector algebra, line, surface and volume integrals, first-order linear differential equations, variation of parameters, Cauchy's and Euler's equations, initial and boundary value problems, PDEs by separation of variables, sampling from distributions, numerical solution of matrix equations, numerical integration, regression and correlation analysis
- Electricity and Magnetism: permeability, self and mutual inductance, magnetic circuits: mmf and reluctance
- Electrical Circuits and Machines: independent, dependent, ideal and practical sources, RLC transients with AC excitation
- Signals and Systems: pulse transfer function
- Control Systems: feedback principles and the role of sensing, time-delay systems, tuning of PID controllers, supervisory control, DCS and PLC
- Analog Electronics: feedback and amplifier design, precision rectifier, oscillators and signal generators, shielding and grounding
- Digital Electronics: arithmetic circuits, data acquisition, virtual instrumentation and IoT
- Measurements: Q-meter, megohm measurement, true rms meters, digital storage oscilloscope
- Communication and Optical Instrumentation: digital modulation: ASK, PSK, FSK, QAM
Asked only once in 5 papers: Taylor and Laurent series (2023), mean, median, mode, standard deviation and variance (2026), numerical methods for differential equations (2024), Coulomb's law, electric field intensity and flux density (2025), Gauss' law (2026), Faraday's law (2022), Kirchhoff's laws, mesh and nodal analysis, star-delta (2026), peak, average and rms values (2024), basic filters with R, L and C (2026), one-port and two-port networks, open and short circuit parameters (2026), sampling (2024), signal flow graphs (2022), transient response (2024), actuators: control valves, servo valves, servo and stepper motors (2024), on-off, P, PI, PID, cascade, feed-forward and ratio controllers (2025), VCO and phase-locked loop (2026), noise and interference: coupling, thermal, shot and flicker noise (2025), number systems (2025), analog front end: analog multiplexer, PGA, sample-and-hold (2025), SI units and standards (2026), uncertainty, accuracy and precision (2023), linear and weighted regression (2024), contact and non-contact current and voltage probes (2025), voltage and current scaling, instrument transformers (2024), piezoelectric sensors (2024), force, torque, vibration and shock (2025), pressure, including low and high pressure (2022), flow: variable head, variable area, electromagnetic, ultrasonic, turbine (2023), liquid level (2024), pH, conductivity and viscosity (2026), pulse code modulation (2026), frequency and time division multiplexing (2022), 4-20 mA two-wire transmitter (2024), interferometers in metrology (2025) and UV-VIS spectrophotometers and the mass spectrometer (2022).
7 questions tested something the syllabus does not name: 2022 Q.29 (three-phase induction motors were dropped from the 2027 IN syllabus); 2023 Q.35 (DC machines are not in the IN syllabus, in 2026 or 2027); 2024 Q.62 (three-phase induction motors were dropped from the 2027 IN syllabus); 2025 Q.46 (three-phase induction motors were dropped from the 2027 IN syllabus); 2022 Q.45 (nonlinear first-order ODEs were dropped from the 2027 IN syllabus); 2025 Q.12 (nonlinear first-order ODEs were dropped from the 2027 IN syllabus); 2023 Q.49 (permutations and counting are not named in the IN syllabus (they sit in General Aptitude)); they count in the subject totals on the weightage page but not under any item here.
Section 1: Engineering Mathematics
41 questions and 60 marks in GATE IN 2022 to 2026. 16 of its 29 syllabus items were asked. Solved questions: GATE IN Engineering Mathematics PYQs.
Official syllabus text
Linear Algebra: Matrix algebra, systems of linear equations, consistency and rank, eigenvalues and eigenvectors, tensors. Calculus: Functions, limits, continuity; differentiation, differentiability, partial derivatives, maxima and minima, integration, multiple integrals, vector algebra, line, surface and volume integrals, Stokes, Gauss and Green's theorems. Differential Equations: Ordinary differential equations, first order linear differential equations, second order linear differential equations with constant coefficients, method of variation of parameters, Cauchy's and Euler's equations, initial and boundary value problems, solution of partial differential equations: variable separable method. Analysis of Complex Variables: Analytic functions, Cauchy's integral theorem and integral formula, Taylor's and Laurent's series, residue theorem, solution of integrals. Probability and Statistics: Random variables, discrete and continuous distributions: normal, Poisson and Binomial distributions. Sampling from distributions, conditional probability and Bayes' theorem, mean, median, mode, standard deviation and variance. Numerical Methods: Solution of matrix equations, solutions of non-linear algebraic equations, iterative methods for solving differential equations, numerical integration, regression and correlation analysis, backpropagation for neural networks.
Matrix algebra, systems of linear equations, consistency and rank
- 2026 Q.14 Number of solutions of Ax = b for a given 3x3 matrix A and vector b
- 2025 Q.11 Rank of a 2n x 2n matrix whose entries are beta or -beta according to the parity of i + j
- 2024 Q.19 Which set of three 3-element column vectors v1, v2, v3 gives a matrix M with rank 3?
- 2023 Q.11 Solution set of the two equations x - 2y + z = 0 and x - z = 0 in three unknowns
- and 2 more (2023, 2022)
eigenvalues and eigenvectors
- 2026 Q.11 3x3 matrix P with P^3 - 4P^2 + 5P - 2I = 0: the set of all possible eigenvalues of P
- 2025 Q.32 Value of x in the matrix [-1 -1; x -4] if an eigenvector is along (alpha, 2 alpha)
- 2024 Q.26 Determinant of P inverse for a real 3x3 matrix P with eigenvalues 1/4, 1 and -2
- 2022 Q.49 Which vectors are eigenvectors of A = [[4, 3], [9, -2]] with eigenvalues -5 and 7?
tensors.
New in 2027: tensors were not in the 2026 IN syllabus and were not asked in GATE IN 2022 to 2026.
Functions, limits, continuity; differentiation, differentiability
partial derivatives, maxima and minima
integration, multiple integrals
Reworded in 2027 (2026: “Mean value theorems, theorems of integral calculus”). 2026 named mean value theorems and theorems of integral calculus; 2027 says integration.
vector algebra
Reworded in 2027 (2026: “vector identities”).
line, surface and volume integrals
Stokes, Gauss and Green's theorems.
Ordinary differential equations, first order linear differential equations
Reworded in 2027 (2026: “First order equation (linear and nonlinear)”). 2027 drops nonlinear first-order equations.
second order linear differential equations with constant coefficients
method of variation of parameters
Cauchy's and Euler's equations
initial and boundary value problems
solution of partial differential equations: variable separable method.
Analytic functions
- 2024 Q.11 The equation conj(z)^2 + z^2 = 2 for z = x + iy: which conic does it represent?
- 2024 Q.49 f(z) = u + iv and its conjugate u - iv are both analytic in a domain: choose the correct options
- 2023 Q.39 The inverse of f(z) = j(1 - z)/(1 + z) maps the real axis to which curve?
- 2022 Q.50 Phase and magnitude of z = (a + jb)/(a - jb) with a, b above zero: which statements are true?
Cauchy's integral theorem and integral formula
Taylor's and Laurent's series
residue theorem, solution of integrals.
Random variables, discrete and continuous distributions: normal, Poisson and Binomial distributions.
Sampling from distributions
Reworded in 2027 (2026: “Sampling theorems”).
conditional probability and Bayes' theorem
Bayes' theorem is now named.
- 2026 Q.36 3 apples and 2 oranges, two drawn in succession: probability first is an apple and second an orange
- 2024 Q.35 One team from each of two pools reaches the final: probability of one blue and one red jersey
- 2022 Q.32 Six red and four blue balls, three drawn without replacement: P(second and third are red)
mean, median, mode, standard deviation and variance.
Solution of matrix equations
Reworded in 2027 (2026: “Matrix inversion”).
solutions of non-linear algebraic equations
iterative methods for solving differential equations
numerical integration
regression and correlation analysis
backpropagation for neural networks.
New in 2027: backpropagation was not in the 2026 IN syllabus and was not asked in GATE IN 2022 to 2026.
Section 2: Electricity and Magnetism
11 questions and 16 marks in GATE IN 2022 to 2026. 7 of its 14 syllabus items were asked. Solved questions: GATE IN Electricity and Magnetism PYQs.
Official syllabus text
Coulomb's law, electric field intensity, electric flux density, Gauss' law, electric field and potential due to point, line, plane and spherical charge distributions, effect of dielectric medium, permittivity, capacitance, magnetic field intensity, magnetic flux density, Biot-Savart's law, Ampere's law, Faraday's law, Lorentz force, permeability, self and mutual inductance, electrical and magnetic dipoles, electromagnetic induction, magnetomotive force, reluctance, magnetic circuits, B-H curve, Maxwell's equations: vector, differential and integral forms.
Coulomb's law, electric field intensity, electric flux density
Gauss' law
electric field and potential due to point, line, plane and spherical charge distributions
- 2026 Q.15 Force on a 1 C charge in the potential V = √(x² + y² + z²) (marks to all in the official key)
- 2026 Q.32 Potential difference v_A - v_B = 5 V: work done moving a charge of 1 coulomb from B to A
effect of dielectric medium, permittivity, capacitance
magnetic field intensity, magnetic flux density
Biot-Savart's law, Ampere's law
Faraday's law
Lorentz force
permeability, self and mutual inductance
electrical and magnetic dipoles
electromagnetic induction
magnetomotive force, reluctance, magnetic circuits
B-H curve
Maxwell's equations: vector, differential and integral forms.
Section 3: Electrical Circuits and Machines
27 questions and 44 marks in GATE IN 2022 to 2026. 11 of its 17 syllabus items were asked. Solved questions: GATE IN Electrical Circuits and Machines PYQs, GATE IN Measurements PYQs.
Official syllabus text
Electrical Circuits: Independent, dependent, ideal and practical sources; V-I characteristics of practical current and voltage sources, battery, solar cell, resistor, inductor, coupled inductor, capacitor; transient analysis of RC, RL, LC, RLC circuits; power and energy consumption, power rating of components, efficiency and losses. Kirchhoff's laws, mesh and nodal analysis, star-delta transformation, superposition, Thevenin's, Norton's, Miller's, maximum power transfer and reciprocity theorems. Peak, average and rms values of AC quantities; apparent, active and reactive powers, power factor; phasor analysis, impedance and admittance; series and parallel resonance, locus diagrams, realization of basic filters with R, L, and C elements; transient analysis of RLC circuits with AC excitation. Analysis of one-port and two-port networks with controlled voltage and current sources, driving point impedance and admittance, open and short circuit parameters. Electrical Machines: Single phase transformers, permanent magnet synchronous machines; buck and boost converters, rectifiers, single phase inverters; rotor position and speed sensing, current sensing, pulse width modulation (PWM) control.
Independent, dependent, ideal and practical sources
V-I characteristics of practical current and voltage sources, battery, solar cell, resistor, inductor, coupled inductor, capacitor
Battery and solar-cell characteristics are now named.
- 2025 Q.24 Coupled inductors 3 H and 2 H with mutual inductance 4 H and given dots: equivalent T-model L1, L2, L3
- 2024 Q.63 Two equal coupled coils: 500 mH series-aiding, 300 mH series-opposing, find the coupling coefficient
- 2023 Q.55 4 H and 5 H coupled inductors with k = 0.6 carrying 1 mA and 2 mA sine currents: peak stored energy
transient analysis of RC, RL, LC, RLC circuits
- 2025 Q.63 Switch across a 10 mA source opens at t = 0, 0.2 H inductor in network: i(t) in the 120 ohm branch at 2 ms
- 2024 Q.33 Switch opened at t = 0 in a 12 V circuit with 4 ohm, 0.25 H, 4 ohm and 0.1 F: dv_c/dt at t = 0+
- 2023 Q.47 Parallel R-L circuit, step current I0 u(t), initial inductor current I0/5: time to reach 99% of final value
power and energy consumption, power rating of components, efficiency and losses.
Kirchhoff's laws, mesh and nodal analysis, star-delta transformation
Star-delta transformation is now named.
superposition, Thevenin's, Norton's, Miller's, maximum power transfer and reciprocity theorems.
Miller's theorem is now named.
- 2025 Q.45 18 V bridge with 3k/6k and 6k/3k arms as common-mode source plus two 3 V sources: R1, R2 and V_C?
- 2023 Q.31 Thevenin equivalent resistance across a and b in a network of 1 ohm resistors with 1 V and 1 A sources
- 2022 Q.54 Circuit A gives I1 = 2 A and I2 = 1/3 A. Same network in Circuit B with 8 V and 48 V: find I3
Peak, average and rms values of AC quantities
apparent, active and reactive powers, power factor
- 2025 Q.65 Active power from a 100 angle 0 deg V source: -j10 and 10 ohm in series with (5 - j5) ohm parallel j5 ohm
- 2024 Q.30 Average power absorbed by a circuit with a DC plus two-harmonic voltage and a two-harmonic current
- 2022 Q.52 Load of R1 in parallel with C1, in series with L1 and R2, driven by 100 V at 50 Hz: power factor
phasor analysis, impedance and admittance
- 2026 Q.33 Series RL circuit, current lags the source by 45 degrees, R = 100 pi ohm and L = 2 H: source frequency
- 2025 Q.25 Admittances -j0.2 S, 0.3 S and j0.4 S in parallel on 10 angle 45 deg V: phase of Ib + Ic against total current
- 2022 Q.60 1 kHz generator, 50 ohm source, 10 Vp-p open circuit falls to 8 Vp-p with a capacitor: capacitance
series and parallel resonance, locus diagrams
- 2023 Q.46 R1-L branch in parallel with R2-C branch at 100 pi rad/s: capacitance C for which Y_in is purely real
- 2023 Q.65 Source 10 sqrt(2) sin(20000 pi t) V with 50 ohm internal resistance: RMS current in a series R, L, C loop
- 2022 Q.33 Band-pass filter with R0 = 50 ohm, L0 = 1 mH, C0 = 10 nF in series, output across R0: Q factor
realization of basic filters with R, L, and C elements
transient analysis of RLC circuits with AC excitation.
Analysis of one-port and two-port networks with controlled voltage and current sources, driving point impedance and admittance, open and short circuit parameters.
Networks with controlled (dependent) sources are now named.
Single phase transformers
Reworded in 2027 (2026: “Single Phase Transformer: Equivalent circuit, phasor diagram, open circuit and short circuit tests, regulation and efficiency”). 2026 listed the equivalent circuit, OC/SC tests, regulation and efficiency; 2027 says only single phase transformers.
- 2026 Q.17 Single phase step-down transformer: how the secondary load impedance referred to the primary compares with Z2
- 2026 Q.58 10 kVA, 1100 V / 220 V transformer, open circuit test on LV side 220 V, 363 W, 2.75 A: Xm referred to HV
- 2025 Q.60 Source 25 sqrt(2) angle 30 deg V through two ideal 1:10 transformers to 50 kilohm: average power in the load
- 2024 Q.61 50 kVA transformer, 95 % efficient at full load and unity pf: efficiency at 75 % load and 0.8 pf
- and 1 more (2023)
permanent magnet synchronous machines
New in 2027, replacing three-phase induction motors: not asked in GATE IN 2022 to 2026.
buck and boost converters, rectifiers, single phase inverters
rotor position and speed sensing, current sensing, pulse width modulation (PWM) control.
Section 4: Signals and Systems
31 questions and 46 marks in GATE IN 2022 to 2026. 9 of its 10 syllabus items were asked. Solved questions: GATE IN Signals and Systems PYQs.
Official syllabus text
Periodic, aperiodic and impulse signals; sampling; Fourier series, Laplace, Fourier and z-transforms, DFT and FFT; continuous-time and discrete-time systems, transfer function, linear time invariant systems, impulse response, frequency response, pulse transfer function; convolution, correlation; basics of IIR and FIR filters.
Periodic, aperiodic and impulse signals
- 2026 Q.19 Fundamental period of x(t) = 4 sin(15 pi t) + 7 cos(4 pi t), t in seconds
- 2026 Q.41 Plot of y(t) = 1 - x(4 - t) from a given plotted signal x(t): which of four plots
- 2025 Q.16 Fundamental period of the magnitude of x(t) = e^(j9t) + e^(j5t), t in seconds
- 2023 Q.28 Discrete-time signal x[n] = u[-n+5] - u[n+3]: smallest n for which x[n] = 0
- and 1 more (2023)
sampling
Reworded in 2027 (2026: “Shannon's sampling theorem”). Moved here from Communication (2026: Shannon's sampling theorem).
Fourier series
Reworded in 2027 (2026: “Fourier series”). Moved here from Engineering Mathematics (2026 listed Fourier series under calculus).
Laplace, Fourier and z-transforms
- 2024 Q.38 Region of convergence of the z-transform of x[n] = (0.2)^n for 0 <= n <= 7
- 2024 Q.40 Signal x(t) for X(s) = 1/(s^2 + 13s + 42) with region of convergence -7 < Re{s} < -6
- 2023 Q.37 Laplace transform of x(t) = e^{-3t} u(t - 5), with its region of convergence
- 2023 Q.44 Real causal finite-energy x(t): select all signals whose Fourier transform is purely imaginary
- and 2 more (2022)
DFT and FFT
- 2025 Q.54 DTFT of the 4-point sequence 1, 2, 2, 4 sampled at 2 pi k/3: value of y[0] of the 3-point DFT inverse
- 2024 Q.25 Complex multiplications needed for a 16-point DFT by the decimation-in-time radix-2 FFT
- 2024 Q.53 Value z[0] of the 4-point circular convolution of two sequences from their 4-point DFTs
continuous-time and discrete-time systems, transfer function, linear time invariant systems
- 2026 Q.20 Which of three differential equations do not represent a linear dynamical system
- 2026 Q.42 Matching four system responses to linear/non-linear and time-invariant/time-varying properties
- 2025 Q.51 Eigenfunctions of stable LTI continuous-time systems: e^(j2pi t/3), cos, 2^t or sin?
- 2022 Q.11 System dy/dt + y = 3x(t-3)u(t-3): transfer function including the time delay
- and 1 more (2022)
impulse response, frequency response
- 2025 Q.39 Causal LTI system y[n] = (1/alpha) y[n-1] + x[n], initially at rest, input delta[n-p]: value of y[p+1]
- 2024 Q.18 Sinusoidal transfer function whose polar plot is a vertical line downward from the point 1
- 2023 Q.21 Transfer function (s - pi)/(s + pi), steady-state output sin(pi t): which input produces it
- 2023 Q.36 LTI impulse response delta(t) + 0.5 delta(t - 4), input cos(7 pi t / 4): the output
pulse transfer function
convolution, correlation
basics of IIR and FIR filters.
Section 5: Control Systems
24 questions and 40 marks in GATE IN 2022 to 2026. 10 of its 14 syllabus items were asked. Solved questions: GATE IN Control Systems PYQs.
Official syllabus text
Feedback principles, role of sensing in feedback, signal flow graphs, transient response, steady state error, Bode plot, phase and gain margins, Routh and Nyquist criteria, root loci, state-space representation of systems; time-delay systems. Actuators for control system: control valves, servo valves, servo motors, stepper motors; on-off, P, PI, PID, cascade, feed forward, and ratio controllers, tuning of PID controllers; design of lead, lag and lead-lag compensators; basic concept of supervisory control, basics of distributed control system (DCS) and programmable logic controller (PLC).
Feedback principles, role of sensing in feedback
signal flow graphs
transient response
steady state error
- 2026 Q.59 Unity negative feedback around G(s) = 10(s+1)/(s(s^2+2s+5)): steady-state error to a unit ramp
- 2025 Q.59 Largest system type for zero steady-state error to a step disturbance (marks to all in the official key)
- 2024 Q.44 Feedback loop 1/(s(s+1)) with gain K in the feedback path: steady-state error to a unit step
- 2022 Q.41 PID on plant 1/((s+1)(s+2)): Kp doubled, Ki tripled, Kd unchanged; effect on steady-state ramp error
Bode plot, phase and gain margins
- 2026 Q.60 G(s) = K/(s+1)^4 with a gain margin of 20 dB: the value of K
- 2023 Q.43 Bode plot with a 34 dB peak at 100 rad/s and phase falling to -720 degrees: matching transfer function
- 2023 Q.50 Phase margin of G(s) = 2(1 - s)/(1 + s)^2 in degrees
- 2022 Q.43 Nyquist plot of a stable open-loop system with points P, Q, R given: phase margin and gain margin
Routh and Nyquist criteria
- 2025 Q.27 Transfer function G(s) = 1 + (2s - 1)/(s^3 + 5s^2 + 3s + 22): number of zeros in the left half of the s-plane
- 2025 Q.28 Nyquist contour (counterclockwise) encircles two poles of G(s)H(s): statement for closed-loop stability
- 2023 Q.24 Number of zeros of P(s) = s^3 + 2s^2 + 5s + 80 in the right-half plane
- 2023 Q.25 Times the Nyquist plot of G(s)H(s) = (1/2)(s-1)(s-2)/((s+1)(s+2)) encircles the origin
- and 1 more (2022)
root loci
state-space representation of systems
time-delay systems.
Actuators for control system: control valves, servo valves, servo motors, stepper motors
Reworded in 2027 (2026: “servo and stepper motors, servo valves”). Control valves are now named as actuators; sizing of control valves was dropped.
on-off, P, PI, PID, cascade, feed forward, and ratio controllers
tuning of PID controllers
design of lead, lag and lead-lag compensators
basic concept of supervisory control, basics of distributed control system (DCS) and programmable logic controller (PLC).
Moved here from Digital Electronics; supervisory control is new.
Section 6: Analog Electronics
30 questions and 48 marks in GATE IN 2022 to 2026. 9 of its 14 syllabus items were asked. Solved questions: GATE IN Analog Electronics PYQs, GATE IN Communication and Optical Instrumentation PYQs.
Official syllabus text
Types of diode and their applications; BJT and MOSFET circuits, biasing, power dissipation, DC analysis, small signal analysis, frequency response of transistor circuits, feedback, amplifier design. Characteristics of ideal and practical operational amplifiers; applications of opamps: adder, subtractor, integrator, differentiator, difference amplifier, instrumentation amplifier, precision rectifier, active filters, comparators, Schmitt trigger, multivibrators, oscillators, signal generators, voltage-controlled oscillators and phase-locked loop. Sources and effects of noise and interference in electronic circuits; conductively, capacitively, inductively coupled interference; noise generated by electronic components, thermal noise, shot noise, flicker noise; shielding and grounding. Basic principles of component selection based on specifications, circuit board realization and testing.
Types of diode and their applications
Reworded in 2027 (2026: “Characteristics and applications of diode, Zener diode”).
- 2026 Q.34 15 cos wt source, 4 ohm, then a 3 V Zener in series with 8 ohm: maximum value of the output voltage
- 2023 Q.33 Ideal diode across a current source of pi sin(3000 pi t) mA: average current through resistor R
- 2022 Q.31 Zener 4 V regulator from 16 V through 1200 ohm, minimum Zener current 4 mA: maximum load current
- 2022 Q.36 Ideal diode into a 0.1 uF capacitor starting at 0.3 V, input peaks 0.4, 1.0, 0.6 V: Vout at 5 ms
- and 1 more (2022)
BJT and MOSFET circuits, biasing, power dissipation, DC analysis
Biasing, DC analysis and power dissipation are now named.
- 2026 Q.22 BJT bias circuit with beta 100 and VBE 0.65 V, 5 V supply, all resistors 5 kilohm: quiescent collector current
- 2025 Q.35 BJT with very high beta, Zener base reference 4.7 V and 1 kilohm emitter resistor: LED current in mA
- 2024 Q.24 NMOS amplifier with 100 kilo-ohm drain-gate feedback, 3.3 kilo-ohm load, 3.3 V supply: drain current
- 2022 Q.58 NPN BJT with R1 = 100 kohm from collector to base and R2 = 1 kohm, VCE = 5.2 V: current gain beta
small signal analysis, frequency response of transistor circuits
Frequency response of transistor circuits is now named.
- 2026 Q.21 A common gate MOSFET amplifier represents which type of controlled source
- 2023 Q.56 nMOS amplifier, muCox 1 mA/V2, VT 1 V, W/L 2, drain bias 4 V, 1 kohm source resistor: Vout/Vin
- 2022 Q.44 Small-signal MOSFET with grounded gate, RL in the drain and RS in the source: impedance looking into node P
- 2022 Q.47 Small-signal MOSFET with three R0 resistors, signal vd injected at the supply: gain vo/vd
feedback, amplifier design.
Reworded in 2027 (2026: “feedback amplifiers.”).
Characteristics of ideal and practical operational amplifiers
- 2024 Q.41 Op-amp A1 with 1 mV offset feeding inverting stage A2: output voltages for zero input
- 2023 Q.26 Inverting op-amp, 1 kohm and 100 kohm, 1 nA bias current and 10 uV offset: worst-case output in uV
- 2023 Q.62 Ideal op-amp with 3R, R, R, R network, 1 V source: output voltage Vo
- 2022 Q.35 Op-amp with gain 10^4, 10 Mohm input and 100 ohm output impedance as a unity-gain buffer: Zout
adder, subtractor, integrator, differentiator, difference amplifier, instrumentation amplifier
- 2026 Q.45 Two op-amp instrumentation amplifier with R 1 kilohm, Rf 10 kilohm, Vin 100 mV and +/-15 V supplies: Vout
- 2025 Q.20 Ideal opamp circuit with R1 to R4: ratio V/I of the source voltage to the current it supplies
- 2025 Q.31 Which ideal-opamp circuits perform a non-linear operation: in-amp, Schmitt trigger, log amp, rectifier?
- 2024 Q.59 Op-amp integrator (1 kilo-ohm, 2 microfarad) driven by 5 V pulses: output voltage at t = 2 ms
- and 3 more (2023, 2022)
precision rectifier
active filters
comparators, Schmitt trigger, multivibrators
Reworded in 2027 (2026: “comparators, Schmitt trigger, multi-vibrators”). Moved here from Digital Electronics.
oscillators, signal generators
voltage-controlled oscillators and phase-locked loop.
Sources and effects of noise and interference in electronic circuits; conductively, capacitively, inductively coupled interference; noise generated by electronic components, thermal noise, shot noise, flicker noise
Coupling paths and thermal, shot and flicker noise are now named.
shielding and grounding.
Reworded in 2027 (2026: “shielding and grounding.”). Moved here from Measurements.
Basic principles of component selection based on specifications, circuit board realization and testing.
Section 7: Digital Electronics
28 questions and 43 marks in GATE IN 2022 to 2026. 12 of its 17 syllabus items were asked. Solved questions: GATE IN Digital Electronics PYQs.
Official syllabus text
Basics of number systems. Combinational logic circuits, multiplexer and demultiplexer, truth table, minimization of Boolean functions; IC families: ECL, TTL and CMOS, CMOS implementation of logic gates; arithmetic circuits, sequential circuits, finite state machines, flipflops, shift registers, timers and counters. Analog front end: analog multiplexer, programmable gain amplifier, sample-and-hold circuit; analog-to-digital converters (ADC) (successive approximation, integrating, flash and sigma-delta) and digital-to-analog converters (DAC) (weighted R, R-2R ladder and current steering logic); characteristics and specifications of ADC and DAC (dynamic range, resolution, quantization, significant bits, conversion/settling time, INL, DNL, ENOB); embedded systems: common microprocessors and microcontrollers, memory and input-output interfacing, embedded systems programming; basics of data acquisition systems, virtual instrumentation, IoT; basic AI applications in instrumentation (sensor linearization, system calibration and tuning, signal classification).
Basics of number systems.
Combinational logic circuits, multiplexer and demultiplexer, truth table
- 2025 Q.17 Minimised Boolean function Y(P, Q, R) of two cascaded multiplexers (4-to-1 into 2-to-1)
- 2023 Q.17 Match the XOR operations X with X, X with X-bar, X with 0 and X with 1 to their results
- 2022 Q.21 Logic block of two inverters and three NOR gates with inputs A and B: output F
- 2022 Q.23 Two cascaded 2x1 multiplexers with constants 1 and 0, selects B and A: forms of the output F
minimization of Boolean functions
- 2025 Q.29 Boolean function X = A'B' + A'C': reduced form of the complement of X
- 2024 Q.16 Simplify the Boolean function F = (A + A'B) + A'(A + B')C
- 2023 Q.40 Simplify F(W,X,Y,Z) = sum of minterms 4, 5, 10, 11, 12, 13, 14, 15 with fewest terms and literals
- 2022 Q.48 2-bit unsigned numbers A = a1 a0 and B = b1 b0: minimised Boolean form of F = 1 only when A > B
IC families: ECL, TTL and CMOS, CMOS implementation of logic gates
ECL and CMOS implementation of logic gates are now named.
- 2026 Q.55 Boolean function of a CMOS logic gate (marks to all in the official key)
- 2023 Q.22 Choose the fastest logic family among TTL, ECL, CMOS and RTL
arithmetic circuits
sequential circuits
finite state machines
flipflops, shift registers
- 2026 Q.47 Four D flip-flops with XOR feedback, initial state 1011: state after two rising clock edges
- 2023 Q.16 Flip-flop table: Q(t) 0,0,1,1 and Q(t+1) 0,1,0,1 with one control input 0,1,1,0: which flip-flop?
- 2023 Q.42 Shift registers A = 1101 and B = 1010 with XOR and NOT feedback, shift control high: contents after 4 clocks
timers and counters.
Analog front end: analog multiplexer, programmable gain amplifier, sample-and-hold circuit
analog-to-digital converters (ADC) (successive approximation, integrating, flash and sigma-delta)
digital-to-analog converters (DAC) (weighted R, R-2R ladder and current steering logic)
characteristics and specifications of ADC and DAC (dynamic range, resolution, quantization, significant bits, conversion/settling time, INL, DNL, ENOB)
Dynamic range, INL, DNL and ENOB are now named.
embedded systems: common microprocessors and microcontrollers, memory and input-output interfacing
Reworded in 2027 (2026: “Embedded Systems: Microprocessor and microcontroller applications, memory and input-output interfacing”).
embedded systems programming
basics of data acquisition systems, virtual instrumentation, IoT
basic AI applications in instrumentation (sensor linearization, system calibration and tuning, signal classification).
Section 8: Measurements
28 questions and 46 marks in GATE IN 2022 to 2026. 11 of its 17 syllabus items were asked. Solved questions: GATE IN Measurements PYQs.
Official syllabus text
SI units, standards of basic electrical quantities (R, L, C, voltage, current and frequency), systematic and random errors in measurement, expression of uncertainty, accuracy and precision, propagation of errors, linear and weighted regression; bridges: Wheatstone, Kelvin, Maxwell, Anderson, Schering and Wien bridges for measurement of R, L, C and frequency, typical applications of bridges, Q-meter; megohm measurement; measurement of voltage, current and power in DC, single and three phase AC circuits; contact and noncontact type AC and DC current and voltage probes; true rms meters, voltage and current scaling, instrument transformers, timer/counter, time, phase and frequency measurements, digital voltmeter, digital multimeter, digital energy meter, digital storage oscilloscope, spectrum analyzer.
SI units, standards of basic electrical quantities (R, L, C, voltage, current and frequency)
systematic and random errors in measurement
expression of uncertainty, accuracy and precision
propagation of errors
linear and weighted regression
bridges: Wheatstone, Kelvin, Maxwell, Anderson, Schering and Wien bridges for measurement of R, L, C and frequency, typical applications of bridges
- 2026 Q.24 Kelvin double bridge: measures low or high resistances, built with three- or four-terminal resistors?
- 2025 Q.56 AC bridge, series R-L and parallel R-L arms, R = 300 Ohm, L = 30 mH, R1 = 1000, R2 = 500: balance frequency?
- 2025 Q.61 Bridge at 4 V with 1000/1010 and 1000/1000 arms, 100 Ohm galvanometer: galvanometer current in uA?
- 2024 Q.39 AC bridge, 500 Ohm + 1 H arm, 1000 Ohm ratio arms, 5 sin(5000t) V: series R and C at balance?
- and 5 more (2024, 2023, 2022)
Q-meter
megohm measurement
measurement of voltage, current and power in DC, single and three phase AC circuits
DC circuits are now named.
- 2025 Q.21 Wattmeter with pressure coil on the supply side (A) or load side (B): condition for low error in both?
- 2025 Q.44 Two-wattmeter method, balanced load 30 kW per phase at 0.866 pf lagging: the two wattmeter readings?
- 2023 Q.34 100 W wattmeter with 2:1 and 1:1 transformers, 100 ohm load, Vs = 200 V RMS: what does it read?
- 2023 Q.61 Multiplier with 1 ohm shunt, A1 = 1/(50 sqrt 2), +90 deg shifter; 230 V, load 230/sqrt2 (1 + j): |avg Vo|?
- and 1 more (2022)
contact and noncontact type AC and DC current and voltage probes
true rms meters
voltage and current scaling, instrument transformers
timer/counter, time, phase and frequency measurements
- 2026 Q.48 Lissajous pattern with 3 horizontal and 2 vertical tangencies, X channel at 600 Hz: Y channel frequency?
- 2026 Q.62 Counter clock 0.1 us, gated for one period of a ~100 kHz input: maximum error in measured frequency (kHz)?
- 2024 Q.60 Switching phase-sensitive detector, V_sense 2 sin(4000 pi t), V_ref 4 sin(2000 pi t), 1 Hz PMMC: reading?
digital voltmeter, digital multimeter
digital energy meter
digital storage oscilloscope
spectrum analyzer.
Section 9: Sensors and Industrial Instrumentation
32 questions and 46 marks in GATE IN 2022 to 2026. 12 of its 12 syllabus items were asked. Solved questions: GATE IN Sensors and Industrial Instrumentation PYQs.
Official syllabus text
Resistive, capacitive, inductive, piezoelectric, electromagnetic and Hall effect sensors and associated signal conditioning circuits; transducers for industrial instrumentation: displacement, velocity, acceleration (linear and angular), force, torque, vibration, shock, pressure (including low and high pressure), flow (variable head, variable area, electromagnetic, ultrasonic, turbine flowmeters), temperature (thermocouple, bolometer, 2, 3, 4 wire RTD, thermistor, pyrometer and semiconductor sensor), liquid level, pH, conductivity and viscosity measurement.
Resistive
- 2026 Q.25 Two active gauges in a half bridge on a cantilever, 10 V supply, 1 mV output, GF 2.5: strain in microstrain?
- 2025 Q.53 Three-wire strain gauge, GF 2, RN 125 Ohm, strain 2e-3, leads 5, 5, 4.95 Ohm: measured strain?
- 2024 Q.51 Full bridge of R +/- dR gauges (R = 4.5 kOhm, dR = 1.5 kOhm) read by an INA: resistance between A and B?
- 2023 Q.51 72-turn wire-wound potentiometer, 0 V to 3.6 V; wiper bridges turns 35 and 36: output voltage?
- and 2 more (2023, 2022)
capacitive
- 2026 Q.50 Parallel-plate capacitive sensor, area 2 cm^2, gap reduced from 0.5 mm by 0.1 mm: percentage change in C?
- 2025 Q.57 Electrostatic actuator, plates 100 um x 100 um, d0 = 1 um, k = 0.01 N/m: charge to close the gap?
- 2024 Q.15 Parallel plates with air gap d1 over a solid dielectric d2 (eps2): capacitance when d1 falls by delta d1?
- 2024 Q.52 Capacitive sensor (100 nF) in an op-amp relaxation oscillator, R = 1 kOhm, 10k/16k divider: output frequency?
- and 1 more (2023)
inductive
- 2025 Q.13 Hand-held metal detector for frisking: reluctance, conductance, electric field or eddy currents?
- 2025 Q.14 LVDT read by a true RMS voltmeter: 0.2 V at x = +2 mm; reading at x = -3 mm?
- 2024 Q.56 Inductive sensors 2 mH and 4 mH driven by +/-6 sin(2000 pi t), driven-shield cable, gain 2: RMS Vout?
- 2023 Q.12 Coil reads 10 mH at 10 kHz; a pure copper sheet is brought near it: what does the LCR meter read now?
- and 1 more (2023)
piezoelectric
electromagnetic and Hall effect sensors
displacement, velocity, acceleration (linear and angular)
force, torque, vibration, shock
pressure (including low and high pressure)
flow (variable head, variable area, electromagnetic, ultrasonic, turbine flowmeters)
Reworded in 2027 (2026: “flow (variable head, variable area, electromagnetic, ultrasonic, turbine and open channel flow meters)”). Open channel flow meters were dropped for 2027.
temperature (thermocouple, bolometer, 2, 3, 4 wire RTD, thermistor, pyrometer and semiconductor sensor)
Reworded in 2027 (2026: “RTD (3/4 wire)”).
- 2026 Q.30 Thermocouple: which is correct, Seebeck effect, resistance change, linear EMF or Joule heating?
- 2026 Q.51 Pyrometer read 1000 C assuming emissivity 0.8; true emissivity 0.7: actual temperature nearest to?
- 2025 Q.58 Thermistor reads 2.25 kOhm at 30 C and 1.17 kOhm at 60 C: material constant beta?
- 2024 Q.14 Match optical pyrometer, thermocouple, strain gauge and LVDT with their principle of measurement
- and 2 more (2024, 2022)
liquid level
pH, conductivity and viscosity measurement.
Section 10: Communication and Optical Instrumentation
16 questions and 25 marks in GATE IN 2022 to 2026. 8 of its 12 syllabus items were asked. Solved questions: GATE IN Communication and Optical Instrumentation PYQs, GATE IN Measurements PYQs.
Official syllabus text
Amplitude and frequency modulation and demodulation, pulse code modulation, frequency and time division multiplexing; amplitude, phase, frequency, quadrature amplitude, pulse shift keying for digital modulation and demodulation; functional architectures of transmitters and receivers; instrument and sensor networks, 4–20 mA two-wire transmitter. Optical sources and detectors: LED, laser, photo-diode, light dependent resistor, square law detectors and their characteristics; interferometer: applications in metrology; basics of fiber optic sensing. Near-infrared (NIR) sensing, Ultraviolet-Visible (UV-VIS) spectrophotometers, mass spectrometer.
Amplitude and frequency modulation and demodulation
- 2026 Q.52 AM voltage across a 1 ohm load, efficiency 60% and carrier power 50 W: value of L
- 2024 Q.48 Ultrasonic vibration sensor, 500 Hz/V, f1 = 40 kHz, f2 = 1 kHz, 0.5 V: modulation index and deviation?
- 2022 Q.16 AM wave s(t) = Ac[1 + m(t)] cos(2 pi fc t): which message does an envelope detector recover completely?
pulse code modulation
frequency and time division multiplexing
amplitude, phase, frequency, quadrature amplitude, pulse shift keying for digital modulation and demodulation
Reworded in 2027 (2026: “quadrature amplitude, pulse shift keying for digital modulation”).
functional architectures of transmitters and receivers
instrument and sensor networks
4–20 mA two-wire transmitter.
Reworded in 2027 (2026: “4-20 mA two-wire transmitter.”). Moved here from Sensors and Industrial Instrumentation.
Optical sources and detectors: LED, laser, photo-diode, light dependent resistor, square law detectors and their characteristics
- 2026 Q.28 Laser diode with slope efficiency 0.5 W/A and 30 mW output at 100 mA: threshold current
- 2026 Q.65 Photodiode with responsivity 0.8 A/W, 2 mW input power: power delivered to a 50 ohm load
- 2023 Q.18 An LED emits light when it is ___ biased; a photodiode is most sensitive when ___ biased
- 2023 Q.38 p-i-n photodiode: 8e12 photons at 1.55 um give 4e12 collected electrons: quantum efficiency in %?
- and 2 more (2022)
interferometer: applications in metrology
basics of fiber optic sensing.
Near-infrared (NIR) sensing
Ultraviolet-Visible (UV-VIS) spectrophotometers, mass spectrometer.
Reworded in 2027 (2026: “UV-VIS Spectrophotometers, Mass spectrometer.”).
How many sections are in the GATE IN syllabus?
Ten, unchanged in name for 2027: Engineering Mathematics; Electricity and Magnetism; Electrical Circuits and Machines; Signals and Systems; Control Systems; Analog Electronics; Digital Electronics; Measurements; Sensors and Industrial Instrumentation; and Communication and Optical Instrumentation. General Aptitude (15 marks) is common to all GATE papers and has its own four-part syllabus: verbal, quantitative, analytical and spatial aptitude.
Where is the official GATE 2027 IN syllabus PDF?
On the GATE 2027 website run by IIT Madras, under Exam Papers and Syllabus: the file is IN_GATE2027_Syllabus.pdf. This page reproduces its wording item by item, marks what changed against the GATE 2026 PDF, and adds which items were actually asked in GATE IN 2022 to 2026. GATE 2027 runs from 6 to 21 Feb 2027.
How this page was made
We split the official IN syllabus into 156 items, keeping IIT Madras's wording, and compared the IN PDF word by word with the GATE 2026 one to mark what changed. Then we filed each of the 272 solved questions from the GATE IN 2022 to 2026 papers under the one item it mainly tests, and 3 of the 3 questions the official keys gave marks to all for by their topic. A question that needs two topics counts once, under the one that does the work, so read the counts as "how often this was the point of a question". Marks come from the official answer keys; the per-paper section totals are on the GATE IN weightage page.