GATE Instrumentation (IN): Communication and Optical Instrumentation (AM, FM, PCM and TDM, photodiodes, LEDs and lasers, fibre optics, interferometers and spectrophotometry), previous-year questions solved

Every communication and optical instrumentation question from the last five GATE Instrumentation Engineering papers, solved: amplitude and frequency modulation, chopper amplifiers and synchronous demodulation, pulse code modulation and time-division multiplexing, LED and photodiode bias, laser diodes, optical fibres and fibre Bragg gratings, interferometers and absorption spectroscopy. Each answer matches the official key and was recomputed by code from a model with the values printed in the paper.

Questions from official GATE IN papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 19 Nov 2026 · 16 questions

GATE 2022 · IN · Q.16MCQ · 1 markAnalog modulation: AM, FM and demodulation

AM wave s(t) = Ac[1 + m(t)] cos(2 pi fc t): which message does an envelope detector recover completely?

A sinusoidal carrier wave with amplitude and frequency is amplitude modulated with a message signal having frequency to generate the modulated wave given by The message signal that can be retrieved completely using envelope detection is ________
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. An envelope detector follows the outline of the peaks of the carrier. For the outline is , because an envelope can never be negative.
  2. The message comes back as only if at every instant, that is, if . This is the condition , a modulation index of at most 100%.
  3. (A) swings between and . So stays between and , never negative. The envelope is a faithful copy of the message.
  4. (B) goes down to , so reaches . (C) and (D) have amplitude 2 and reach for . Each is overmodulated: the carrier phase reverses and the envelope gets folded back, so the detector output is a distorted, rectified message.
  5. Only (A) keeps non-negative. The answer is (A).

Trap: thinking only about the frequency . That condition lets the detector follow the envelope; it does not stop overmodulation. We built the modulated wave for each message and ran a numerical envelope detector on it (rectify, average over one carrier cycle, scale by ). The worst error against the true message was 0.002 for (A), but 1.00 for (B), 1.98 for (C) and 1.98 for (D), where the message amplitude was 1.5, 2 and 2.

Where this shows up in industry

Envelope detection is how simple AM radio receivers, and the diode detector in many RF test probes, recover the audio or the envelope of a signal. Transmitters hold the modulation index below 100% for exactly this reason, and the same limit shows up in carrier-based sensor read-outs such as LVDT and strain-gauge amplifiers.

GATE 2024 · IN · Q.48MCQ · 2 marksAnalog modulation: AM, FM and demodulation

Ultrasonic vibration sensor, 500 Hz/V, f1 = 40 kHz, f2 = 1 kHz, 0.5 V: modulation index and deviation?

Consider an ultrasonic measurement system shown in the figure. The ultrasonic transmitter (T) sends a continuous wave signal volts towards an object whose vibration is modeled as volts. Neglecting the phase shift due to any other effect, the received signal at the receiver (R) is volts.

Assuming the frequency sensitivity factor as 500 Hz/volt, kHz, kHz, the modulation index () and the frequency deviation in , respectively, are

An ultrasonic transmitter T sends a continuous wave x(t) towards a vibrating object. The wave travels a distance L to the object, which moves to and fro with displacement signal m(t), and reflects a distance L at an angle theta to the ultrasonic receiver R, which outputs y(t).ObjectTUltrasonictransmitterx(t)RUltrasonicreceivery(t)LLθm(t)
  1. (A)0.25 and Hz
  2. (B)0.5 and Hz
  3. (C)1 and Hz
  4. (D)0.75 and Hz

Answer: (A) Official key: A

  1. The received wave is frequency modulated by the vibration. Its instantaneous frequency is , with the frequency sensitivity .
  2. The frequency deviation is the largest swing of from . The peak of is , so . That is about the 40 kHz carrier.
  3. The modulation index is the deviation divided by the message frequency: .
  4. Check from the phase. The phase of is , and has peak . So the peak phase swing is rad, the same . The integral of a sine is a negative cosine, so the sign differs from the printed , but the question asks for sizes only.
  5. Answer: (A) 0.25 and Hz.

Trap: using 1 V instead of the 0.5 V amplitude gives and 500 Hz, option (B). Also, is divided by the message frequency (1 kHz), not the carrier (40 kHz). Because is well below 1 this is narrowband FM: the spectrum is the carrier plus one pair of sidebands. Carson's rule gives a bandwidth of about . We built in the time domain, differentiated its phase to get the deviation (250.0 Hz) and index (0.250), and checked the carrier and sideband lines against the Bessel functions: , . Only option (A) matched.

Where this shows up in industry

Ultrasonic and laser Doppler vibrometers, and flow and level meters that use a moving reflector, return a wave whose phase or frequency carries the motion, so the signal is demodulated as FM. Choosing the demodulator bandwidth with Carson's rule keeps the vibration spectrum without letting in extra noise.

GATE 2025 · IN · Q.41MCQ · 2 marksAnalog modulation: AM, FM and demodulation

Chopper amplifier, A = 100, signal to 50 Hz, offset to 10 Hz, low-pass at pi/T: s(t) frequency?

A chopper amplifier shown in the figure is designed to process a biomedical signal to generate conditioned output . The signals and are band limited to 50 Hz and 10 Hz, respectively. For the system to operate as a linear amplifier, choose the correct statement from the following options.
Chopper amplifier block diagram. The input vin(t) is multiplied by a square wave s(t) that alternates between plus 1 and minus 1 with a 50 percent duty cycle and period T. A signal vos(t) is added to the product, the sum goes through an amplifier of gain A equal to 100, and is multiplied by s(t) again. The result passes through a low-pass filter H2 whose gain is 1 up to an angular frequency of pi over T, giving the output vout(t). The dashed box encloses the whole chopper amplifier.Chopper amplifiervin (t)A = 100H2 (jω)vout (t)s(t)vos (t)s(t)s(t)t1−1…Tduty cycle = 50%|H2 (jω)|ω1πT0
  1. (A)The minimum frequency of required is 100 Hz and gets attenuated by the system
  2. (B)The minimum frequency of required is 100 Hz and also gets amplified by the system by a factor
  3. (C)The minimum frequency of required is 80 Hz and gets attenuated by the system
  4. (D)The minimum frequency of required is 80 Hz and also gets amplified by the system by a factor

Answer: (A) Official key: A

  1. The first multiplier is a modulator: it moves to the square wave's odd harmonics. The amplifier adds (offset and low-frequency noise) after the modulator. The second multiplier is the demodulator.
  2. Because , . So the signal before the filter is .
  3. The wanted signal is back at baseband, amplified by , with no distortion. The offset is now multiplied by , so it has moved up to odd harmonics of the chopping frequency, Hz, Hz and so on.
  4. Let be the period of , so . The filter passes , that is frequencies up to .
  5. To pass the 50 Hz signal, Hz, so Hz. At 100 Hz the filter edge is 50 Hz and the nearest offset line is at Hz, well above it, so the offset is attenuated. At 80 Hz the edge is 40 Hz and the biomedical signal itself would be cut, so 80 Hz fails.
  6. Answer: (A). The factor is the size of the first offset sideband before filtering; it would reach the output only if the filter passed it.

Trap: reading as the chopping frequency itself. Reading the filter edge as the chopping frequency (not half of it) would suggest that 50 Hz chopping is enough, but then the offset lines at 40 and 60 Hz would also pass. Another trap is thinking the chopper amplifies the offset because the amplifier sits between two multipliers; the offset enters after the first multiplier, so only the second one chops it. We checked the identity on random values, then built the exact odd-harmonic lines of the chopped offset and tested every chopping frequency from 1 Hz to 400 Hz against an ideal low-pass filter at : the minimum frequency that keeps the 50 Hz signal and rejects every offset line is 100 Hz. At 80 Hz the signal gain is 0; at 100 Hz the signal gain is 100 and the offset gain is 0.

Where this shows up in industry

Chopper-stabilised and zero-drift amplifiers use this scheme to remove input offset and 1/f noise in thermocouple, strain-gauge, ECG and EEG front ends. The chopping frequency is set well above the signal band so the filter can separate the two.

GATE 2026 · IN · Q.52MCQ · 2 marksAnalog modulation: AM, FM and demodulation

AM voltage across a 1 ohm load, efficiency 60% and carrier power 50 W: value of L

An amplitude modulated voltage signal drives a load of 1 . . If the efficiency is 60% and the carrier power is 50 W, the value of is ______ V.
  1. (A)8.66
  2. (B)1.22
  3. (C)0.81
  4. (D)17.32

Answer: (A) Official key: A

  1. Read the three terms. The middle frequency is : the carrier, amplitude . The other two are at and , which are the lower and upper sidebands, each of amplitude .
  2. Carrier power in : , so .
  3. Each sideband carries , so the total sideband power is (in watts, for ).
  4. Efficiency is the fraction of total power that sits in the sidebands: .
  5. Solve: , so . Option (A).
  6. Check with the modulation index: , and . An index above 1 means the envelope would over-modulate, but the question only asks for the power split.

Trap: defining efficiency as gives , which is not an option. We built the three-tone signal, found its carrier and sideband power by a Fourier sum over one period, and tested every option: only gives 60% efficiency with a 50 W carrier.

Where this shows up in industry

Broadcast AM transmitters waste most of their power in the carrier, which carries no information, so efficiency and carrier power are quoted to size the power amplifier and the electricity bill. The same sideband bookkeeping tells you how much of a modulated sensor or telemetry signal is actually data.

GATE 2022 · IN · Q.26NAT · 1 markDigital modulation, PCM and multiplexing

24 voice signals time-division multiplexed, 12 kHz sampling, 8-bit words: bit duration in microseconds?

Consider 24 voice signals being transmitted without latency using time-division multiplexing. If each signal is sampled at 12 kHz and represented by an 8-bit word, the bit-duration (in microseconds) is ________ (round off to two decimal places)

Answer: Official key: 0.42 to 0.44

  1. Every channel is sampled times a second. So one frame, which carries one sample from each of the 24 channels, repeats every .
  2. Each sample is an 8-bit word, so a frame holds bits.
  3. These 192 bits must fit into one frame period. The bit rate is .
  4. Bit duration: .

Trap: confusing the bit time with the slot time. One channel's 8-bit word occupies , not . Real telephone multiplexers also add a framing bit: the T1 format uses 193 bits per frame, which gives , still inside the official range. The question says nothing about framing bits, so 192 is the intended count.

Where this shows up in industry

Digital telephone trunks (T1 at 1.544 Mbit/s and E1 at 2.048 Mbit/s) work exactly this way: 8000 samples per second per voice channel, interleaved in time slots. The same time-division idea lets one data link or one fieldbus carry readings from many sensors in turn.

GATE 2026 · IN · Q.27MCQ · 1 markDigital modulation, PCM and multiplexing

PCM of an analog speech signal, 200 Hz to 2400 Hz, sampled at 6 kHz with 512 levels: bit rate

An analog speech signal contains signals from 200 Hz to 2400 Hz. It is sampled at 6 kHz and quantized with 512 levels for pulse code modulation (PCM). The bit rate will be _____ kbps.
  1. (A)16
  2. (B)48
  3. (C)19.2
  4. (D)54

Answer: (D) Official key: D

  1. Pulse code modulation turns each sample into a binary word. With quantisation levels, each word needs bits.
  2. bits per sample.
  3. The question gives the sampling rate directly: . (The Nyquist rate for a 2400 Hz signal would be 4.8 kHz, but the signal is actually sampled faster, and the bit rate follows the real sampling rate.)
  4. Bit rate , which is . Option (D).

Trap: using the Nyquist rate gives 43.2 kbps, which is not an option; using 8 bits per sample gives 48 kbps (option B). We computed the rate for each option from the sampling rate and the word length; only 54 kbps matches.

Where this shows up in industry

Digital telephone lines carry speech at 8 kHz sampling and 8 bits per sample, 64 kbit/s per channel, and these numbers fix how many voice channels fit on a link. Instrument and sensor telemetry links are sized the same way: samples per second times bits per sample gives the minimum data rate the channel must carry.

GATE 2022 · IN · Q.27NAT · 1 markOptical sources and detectors

Photodiode with a band gap of 1.42 eV: cut-off wavelength in nanometres?

A photodiode is made of a semiconductor with a bandgap of 1.42 eV. Given that Planck's constant is , the speed of light in vacuum is , and , the cut-off wavelength (in nanometers) of the photodiode is ________ (round off to one decimal place)

Answer: Official key: 870.0 to 880.0

  1. A photodiode responds only if a photon has enough energy to lift an electron across the band gap: . The longest wavelength that still works is the cut-off: .
  2. Convert the gap to joules: .
  3. .
  4. , in the near infrared.
  5. Shortcut: . This matches gallium arsenide, whose band edge is near 870 nm.

Trap: forgetting to convert electronvolts to joules, or mixing micrometres and nanometres. Photons with a longer wavelength than do not generate carriers, so the detector goes blind above this wavelength. With exact CODATA constants the same calculation gives ; both values lie inside the official range.

Where this shows up in industry

The band gap sets which light a detector can see: silicon stops near 1100 nm, gallium arsenide near 870 nm, and InGaAs is used for the 1310 and 1550 nm telecom bands. Engineers pick the photodiode material from this cut-off before anything else, for optical sensors, fibre links and spectrometers.

GATE 2022 · IN · Q.39MCQ · 2 marksOptical sources and detectors

Laser echo from a car comes back after 100 ns, then 90 ns a tenth of a second later: speed and direction?

A car is moving collinearly with a laser beam emitted by a transceiver. A laser pulse emitted at is received back by the transceiver 100 ns (nanoseconds) later after reflection from the car. A second pulse emitted at is received back 90 ns later. Given the speed of light is , the average speed of the car in this interval is ________
  1. (A)54 kmph, moving towards the transceiver
  2. (B)108 kmph, moving towards the transceiver
  3. (C)54 kmph, moving away from the transceiver
  4. (D)108 kmph, moving away from the transceiver

Answer: (A) Official key: A

  1. The pulse travels to the car and back, so the one-way distance is half of . First pulse: .
  2. Second pulse: .
  3. The echo came back sooner, so the car is nearer: it moved towards the transceiver.
  4. The pulses were emitted apart. The reflection instants differ by , which is to nine digits, so .
  5. Convert: , moving towards the transceiver. The answer is (A).

Trap: forgetting that the light covers the distance twice. Using gives 108 km/h, option (B). The direction also needs care: a shorter echo time means the target is closer. We computed both ranges and the speed between the two reflection instants: 54.000 km/h towards.

Where this shows up in industry

Pulsed time-of-flight is how laser rangefinders, LiDAR sensors, police speed guns and level meters measure distance, and two ranges a known time apart give velocity. Nanosecond timing is needed because light covers 15 cm in 1 ns of round trip, so timing electronics set the range resolution.

GATE 2023 · IN · Q.18MCQ · 1 markOptical sources and detectors

An LED emits light when it is ___ biased; a photodiode is most sensitive when ___ biased

A light emitting diode (LED) emits light when it is ______biased. A photodiode provides maximum sensitivity to light when it is______ biased.
  1. (A)forward, forward
  2. (B)forward, reverse
  3. (C)reverse, reverse
  4. (D)reverse, forward

Answer: (B) Official key: B

  1. LED: a forward bias pushes electrons and holes across the junction, where they meet and recombine. In a direct-gap material each recombination can release a photon. A reverse-biased LED carries almost no current, so there is nothing to recombine and no light.
  2. Photodiode: it works in the opposite direction, turning absorbed photons into current. Light only produces useful, collectable carriers inside the depletion region, where the electric field sweeps electrons and holes out before they recombine.
  3. Reverse bias widens the depletion region, increases the field, and lowers the junction capacitance, so more light is collected and the response is faster. For example, in a silicon diode with , the depletion width grows from 0.36 at to 2.71 at .
  4. Forward bias is the wrong way for a detector: the depletion region collapses and a large dark current flows, which buries the tiny photocurrent.
  5. So the pair is forward for the LED and reverse for the photodiode: option (B).

Trap: remembering only that both are diodes and choosing the same bias for both. Also, a solar cell is a photodiode that is used with no bias to produce power, but a photodiode meant for sensing light uses reverse bias for the best sensitivity and speed. We modelled a silicon photodiode at 850 nm: the collected fraction of photons is 1.9% at against 13.5% at , and the photocurrent is 0.0016% of the total current in forward bias against 100.0% in reverse bias.

Where this shows up in industry

Light barriers, optical encoders, fibre receivers and pulse oximeters all drive an LED forward and read the matching photodiode reverse biased, usually through a transimpedance amplifier. The reverse voltage is chosen to trade speed against dark-current noise.

GATE 2023 · IN · Q.38MCQ · 2 marksOptical sources and detectors

p-i-n photodiode: 8e12 photons at 1.55 um give 4e12 collected electrons: quantum efficiency in %?

In a p-i-n photodiode, a pulse of light containing incident photons at wavelength gives rise to an average electrons collected at the terminals of the device. The quantum efficiency of the photodiode at this wavelength is _______%.
  1. (A)50
  2. (B)54.2
  3. (C)62.5
  4. (D)80

Answer: (A) Official key: A

  1. Quantum efficiency is the number of carriers collected per photon that arrives: .
  2. 50%. The answer is (A).
  3. The wavelength is a distractor for this part. It would matter if the question asked for the responsivity: .

Trap: reading the responsivity of as a percentage, which would suggest option (C), 62.5. Responsivity is amps per watt, quantum efficiency is a unitless ratio, and they are different quantities. The photon energy at 1.55 is 0.80 eV. A single p-i-n diode has no internal gain, so every collected electron needs one absorbed photon; a value of above 100% would signal an avalanche photodiode or an error. We checked every option against : only 50% matches.

Where this shows up in industry

Quantum efficiency and responsivity are the first two numbers on a photodiode datasheet. Receivers for fibre links in the 1550 nm band use InGaAs p-i-n diodes with efficiencies of 60 to 90%, and the figure sets how much optical power a link needs to reach a given signal-to-noise ratio.

GATE 2026 · IN · Q.28MCQ · 1 markOptical sources and detectors

Laser diode with slope efficiency 0.5 W/A and 30 mW output at 100 mA: threshold current

The slope efficiency of a laser diode is 0.5 W/A, and the output optical power at a current of 100 mA is 30 mW. Assuming piece-wise linear characteristics of the laser diode, the threshold current of the laser is ________ mA.
  1. (A)0
  2. (B)20
  3. (C)40
  4. (D)60

Answer: (C) Official key: C

  1. A laser diode gives almost no coherent light below its threshold current . Above threshold, the optical power rises in a straight line: , with the slope efficiency in W/A.
  2. Solve for the threshold: .
  3. . Option (C).

Trap: picking 60 mA, which is the current above threshold (), not the threshold itself. We rebuilt the straight-line curve for each option as the threshold and checked the power at 100 mA: only 40 mA gives 30 mW.

Where this shows up in industry

Laser driver circuits for fibre links, barcode scanners and rangefinders bias the diode just above threshold and add the signal current on top. Because threshold drifts with temperature, drivers monitor the output with a back-facet photodiode and adjust the bias current to keep the output power constant.

GATE 2026 · IN · Q.65NAT · 2 marksOptical sources and detectors

Photodiode with responsivity 0.8 A/W, 2 mW input power: power delivered to a 50 ohm load

A photodiode has a responsivity 0.8 A/W. If the input optical power to the photodiode is 2 mW, the power delivered to a 50 load is _______ W. (rounded off to the nearest integer)

Answer: Official key: 128 to 128

  1. Responsivity links optical power in to current out: , with in A/W.
  2. .
  3. The electrical power in the load is .

Trap: stopping at the photocurrent (1.6 mA) or treating it as a power. The 1.6 mA is a current; the power in the load is , far smaller than the 2 mW of light, which is normal: the photodiode is a current source and delivers little power. For reference, 0.8 A/W at 1550 nm corresponds to a quantum efficiency of 64% using with CODATA constants.

Where this shows up in industry

Photodiode receivers in fibre links, light meters and optical sensors are read as a current, usually through a transimpedance amplifier rather than a plain load, so the signal is 'current out per watt of light'. Knowing the responsivity lets you convert a measured current back to optical power for calibration and power-budget checks.

GATE 2022 · IN · Q.51NAT · 2 marksInterferometry, fibre optics and spectroscopy

UV-Vis spectrophotometer at 532 nm: 0.414 mW/cm2 after 1 cm, 0.186 mW/cm2 after 2 cm: absorption coefficient?

Monochromatic light of wavelength 532 nm is used to measure the absorption coefficient of a material in a UV-Visible Spectrophotometer. The measured light intensity after transmission through a 1 cm thick sample of the material is . For a sample of thickness 2 cm, the measured light intensity is . The absorption coefficient (in ) of the material is ________ (round off to two decimal places)

Answer: Official key: 0.75 to 0.85

  1. The Beer-Lambert law says that light is absorbed exponentially with thickness: , where is the absorption coefficient.
  2. The incident intensity is not given, but it cancels in a ratio. Divide the 1 cm reading by the 2 cm reading: .
  3. .
  4. .
  5. Check: , and , as measured.

Trap: using base-10 logarithms (the absorbance form ), which gives 0.35, or dividing by the 2 cm thickness instead of the 1 cm difference, which gives 0.40. Because the two thicknesses differ by 1 cm, is the natural logarithm of the ratio. The wavelength of 532 nm does not enter the arithmetic; it only says applies to green light. We fitted the two readings and recovered the incident intensity too: .

Where this shows up in industry

UV-Vis spectrophotometers use this law to find the concentration of a dissolved substance from how much light a cuvette absorbs, which is how protein assays, water-quality tests and dye or drug concentration checks are done. Measuring two path lengths, as here, removes the unknown source intensity and any fixed reflection losses.

GATE 2023 · IN · Q.45NAT · 2 marksInterferometry, fibre optics and spectroscopy

Silica fibre core 1.47, cladding 1.44: cladding stripped, core dipped in water 1.33: numerical aperture?

A silica-glass fiber has a core refractive index of 1.47 and a cladding refractive index of 1.44. If the cladding is completely stripped out and the core is dipped in water having a refractive index of 1.33, the numerical aperture of the modified fiber is_______ (rounded off to three decimal places).

Answer: Official key: 0.620 to 0.640

  1. The numerical aperture of a step-index fibre is set by the core index and whatever surrounds the core, : .
  2. After stripping, the surrounding medium is water: . The original cladding of 1.44 no longer matters.
  3. .
  4. The original fibre has . Water has a lower index than the cladding, so the contrast is larger and the fibre accepts light over a wider cone.

Trap: keeping and getting 0.295. Another slip is dividing by the water index, since already includes the index of the outside medium. In water the acceptance half-angle is , but the product stays 0.626. We traced rays with Snell's law and total internal reflection at the core wall and found the largest guided launch angle by bisection: .

Where this shows up in industry

Numerical aperture tells you how much light a fibre collects and how steeply it can be bent before light leaks. It also explains why a bare fibre end behaves differently in water or oil, which matters for immersion probes, fibre chemical sensors and medical fibre probes.

GATE 2025 · IN · Q.55NAT · 2 marksInterferometry, fibre optics and spectroscopy

Michelson interferometer with 2 cm gas chamber: 30 fringes at 532 nm, how many at 632.8 nm?

A schematic of a Michelson interferometer, used for the measurement of refractive index of gas, is shown in the figure. The transparent chamber is filled with a gas of refractive index , where , at atmospheric pressure. If a 532 nm laser beam produces 30 interference fringes on the screen, then the number of fringes produced by a 632.8 nm laser beam will be _____ (rounded off to one decimal place).

Note: Assume that the effect of beamsplitter width is negligible. The setup is placed in air medium with refractive index equal to 1.

Michelson interferometer. A laser beam hits a beamsplitter. One part goes up 5 cm to a mirror and back. The other part goes right, through a 2 cm transparent gas chamber, to a mirror 5 cm from the beamsplitter, and back through the chamber. The two returning beams recombine at the beamsplitter and travel down to a screen where the fringes are counted.BeamsplitterLaser beamMirrorMirrorScreen5 cm5 cm2 cmTransparentchamber

Answer: Official key: 24.5 to 25.5

  1. One fringe appears for every change of one wavelength in the optical path difference between the two arms.
  2. The beam crosses the chamber twice (there and back), each time of length . The gas changes the optical path by compared with air. The two arm lengths, 5 cm each, are equal and cancel.
  3. Number of fringes: . The chamber length and the gas index are the same for both lasers, so is constant (the small change of with wavelength is ignored).
  4. From the first laser: , so .
  5. .

Trap: inverting the ratio. A longer wavelength gives fewer fringes, not more; is outside the key range 24.5 to 25.5. The 5 cm arms and the factor 2 for the double pass cancel out in the ratio, so they are not needed. We took from the 30 fringes, recomputed the count at 632.8 nm (25.22), and checked with three different gas indices that the ratio stays .

Where this shows up in industry

Interferometers count fringes to measure lengths, displacement and surface form to a fraction of a wavelength in metrology labs and machine-tool calibration. The same fringe counting gives the refractive index of gases and the density of air, which is used to correct laser length measurements for temperature and pressure.

GATE 2026 · IN · Q.64NAT · 2 marksInterferometry, fibre optics and spectroscopy

Fibre Bragg grating sensor, Bragg wavelength 1550 nm, effective index 1.44: grating period

For a fiber Bragg grating-based sensor, the shift in the Bragg wavelength gives information about the value of the measurand. For a Bragg wavelength of 1550 nm and effective index of 1.44, the grating period is _______ nm. (rounded off to two decimal places)

Answer: Official key: 537.00 to 539.00

  1. A fibre Bragg grating is a short stretch of fibre where the core index repeats with period . Light reflects strongly at the Bragg wavelength, where the reflections from every period add in step.
  2. The Bragg condition (first order) is . The factor 2 is there because the reflected wave travels the period twice, forward and back.
  3. .
  4. Why it works as a sensor: strain or temperature changes and , so shifts. An interrogator measures that shift.

Trap: dropping the factor 2 gives , which is outside the key range. We inverted the Bragg condition in code and checked it against the key range of 537.00 to 539.00 nm.

Where this shows up in industry

Fibre Bragg gratings are written into fibres to measure strain in bridges, pipelines and aircraft wings, and temperature in boreholes and power cables. Many gratings with different periods can sit on one fibre, each reflecting its own wavelength, so one interrogator reads dozens of points with no electrical wiring at the sensor.

From GATE prep to a instrumentation, telecom or photonics career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.