GATE Instrumentation (IN): Electrical Circuits and Machines (network theorems, transients, AC power, coupled inductors, transformers, induction motors), previous-year questions solved

Every electrical circuits and machines question from the last five GATE Instrumentation Engineering papers, solved: Thevenin resistance, superposition and reciprocity, two-port parameters and maximum power transfer, RL and RC switching transients, RMS and average power of multi-harmonic waveforms, power factor, admittance and resonance, energy and coupling in mutually coupled inductors, transformer tests and efficiency, and induction motor slip and speed. Each answer matches the official key and was recomputed by code, from a nodal solve, complex phasor arithmetic or an equivalent circuit, with the values printed in the paper.

Questions from official GATE IN papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 19 Nov 2026 · 7 of 30 questions on this page

GATE 2022 · IN · Q.54NAT · 2 marksDC networks, network theorems and two-ports

Circuit A gives I1 = 2 A and I2 = 1/3 A. Same network in Circuit B with 8 V and 48 V: find I3

Given Circuit A with currents and as shown, the current in Circuit B (in amperes), is ______ (round off to one decimal place)
Two circuits built on the same network. Both have a left branch of resistor R0 in series with a voltage source, then a 4 ohm resistor and an 8 ohm resistor along the top, and 8 ohm and 6 ohm resistors as vertical branches. Circuit A: the left source is 16 V, the right branch is just R0, current I1 equals 2 A enters from the left and current I2 equals 1/3 A flows down through the right R0. Circuit B: the left source is 8 V, the right branch is R0 in series with a 48 V source, and I3 is the current entering from the left+−R016 V4 Ω8 Ω8 Ω6 ΩR0I1 = 2 AI2 = 1/3 ACircuit A+−R08 V4 Ω8 Ω8 Ω6 Ω+−R048 VI3Circuit B

Answer: Official key: 0.0 to 0.0

  1. The network is linear, so two theorems apply. Superposition: with two sources, add the current caused by each source acting alone. Reciprocity: in a linear network of resistors only, if a source in one branch drives a current in a second branch, then the same source moved to the second branch drives the same current in the first.
  2. Circuit A: a 16 V source on the left gives in the left branch and in the right branch.
  3. Circuit B, 8 V source alone (right source shorted): scale circuit A by . The left branch current is , in the direction of .
  4. Circuit B, 48 V source alone (left source shorted): by reciprocity, a 16 V source in the right branch would give in the left branch. Scale by : . The source pushes current down out of its own branch top into the network, so in the left branch this flows towards the left source, opposite to : .
  5. Add: .

Trap: adding the two contributions as forgets that the right source drives its current into the left branch the other way round. Both sources here are plus-on-top, so they oppose each other at the left node. We checked without the shortcut: the unknown was found by scanning for in circuit A, which gave and then , matching . A three-node nodal solve of circuit B with gave ; the 8 V source alone gives and the 48 V source alone gives .

Where this shows up in industry

Reciprocity is why a sensor bridge or a resistive network behaves the same when the excitation and the measurement points are swapped, and superposition is the everyday way to analyse a circuit with several sources, such as a transducer with an offset supply. Both only hold for linear networks.

GATE 2023 · IN · Q.31NAT · 1 markDC networks, network theorems and two-ports

Thevenin equivalent resistance across a and b in a network of 1 ohm resistors with 1 V and 1 A sources

In the circuit given, the Thevenin equivalent resistance across the terminals 'a' and 'b' is ___________ (rounded off to one decimal place).
Circuit for the Thevenin resistance between terminals a and b. A 1 ohm resistor and a 1 volt source (plus at the top) stand side by side on the left. The top rail runs through a 1 ohm resistor to a node with a branch of a 1 ampere current source (arrow up) above a 1 ohm resistor, then through another 1 ohm resistor to a node with a branch of a 1 ohm resistor above a 1 ampere current source (arrow up), then a branch of two 1 ohm resistors in series, and finally terminal a. Terminal b is on the bottom rail.1 Ω+−1 V1 Ω1 A1 Ω1 A1 Ω1 ΩabRth 1 Ω1 Ω

Answer: Official key: 1.0 to 1.0

  1. Thevenin resistance is the resistance seen at the terminals with every independent source switched off. An ideal voltage source becomes a short circuit (a wire), and an ideal current source becomes an open circuit (a gap).
  2. The source becomes a wire, so the left-hand resistor is shorted and the left end of the top rail is joined to the bottom rail. Each source becomes an open circuit, so the whole branch holding it (with its in series) carries no current and disappears.
  3. What remains between a and b are two parallel paths. The branch of two resistors in series on the right is . The top path, two resistors in series to the (now shorted) left end, is also .
  4. .

Trap: leaving a current source's series resistor in the circuit as if it still conducted. A series element next to an ideal current source never matters for , because that branch is open. As a check we solved the real circuit with all sources on: open-circuit voltage and short-circuit current give , and driving the source-free circuit with a test current gives the same .

Where this shows up in industry

Reducing a sensor network to a Thevenin source tells you the output resistance that a measuring amplifier or data logger will see. That decides how much loading error the input stage adds, and it is the first number checked when matching a bridge or transducer to its front end.

GATE 2026 · IN · Q.39MCQ · 2 marksDC networks, network theorems and two-ports

Two-port with z11 = z22 = 10 ohm, z12 = z21 = 5 ohm, 5 V source and 5 ohm: R_L for maximum power transfer

A two-port network has -parameters , and .
The value of such that maximum power is transferred to is _________ .
A 5 volt source in series with a 5 ohm resistor drives port 1 of a two-port network with z-parameters z11, z12, z21 and z22. Port 2 of the network is loaded by a resistor R L. Both ports have the plus terminal at the top+−z11 z12 z21 z22 5 Ω5 VRL +−+−
  1. (A)5.67
  2. (B)8.33
  3. (C)10.33
  4. (D)25.67

Answer: (B) Official key: B

  1. Maximum power transfer: a load receives the most power from a source when its resistance equals the Thevenin resistance seen looking back into the source. So find the resistance seen at port 2, with the 5 V source set to zero (replaced by a short circuit) and the 5 resistor left in place.
  2. The -parameter equations are and . With the source off, port 1 sees .
  3. Substitute in the first equation: , so .
  4. Then , so .
  5. . Option (B).

Trap: using alone, which ignores the way the source side loads the port through and the 5 resistor, or leaving the 5 out and getting . We solved the loop equations for over a sweep and the delivered power peaked at . At the printed options the power is 80.3 mW (A), 83.3 mW (B), 82.4 mW (C) and 61.7 mW (D).

Where this shows up in industry

Matching a load to the output resistance of a network, here including the loading from the input side, is how engineers get the most signal power out of a sensor front end or a transducer driver. Two-port parameters make that output resistance easy to find without opening up the box.

GATE 2026 · IN · Q.40MCQ · 2 marksDC networks, network theorems and two-ports

Resistor network with two 4 V sources, 1 ohm and 2 ohm resistors: the output voltage V0

In the circuit shown below, the value of the output voltage is _____ V.
A resistor network. Along the top, a wire joins two 2 ohm resistors to ground, then a 1 ohm resistor, then a node with a 2 ohm resistor in series with a 4 volt source (plus at the top) to ground, then another 1 ohm resistor, then a last node with another 2 ohm resistor in series with a 4 volt source (plus at the top) to ground. The output V 0 is taken from that last node to ground2 Ω2 Ω+−2 Ω4 V+−2 Ω4 V1 Ω1 Ω+−V0
  1. (A)2
  2. (B)3
  3. (C)4
  4. (D)8

Answer: (B) Official key: B

  1. Use nodal analysis, which writes Kirchhoff's current law at each unknown node. Call the three top nodes , and , with the bottom wire at .
  2. The two resistors at node 1 are in parallel to ground, which makes . Node 1: , so .
  3. Node 3 (the output): , so .
  4. Node 2: . With this becomes , so .
  5. Equate the two expressions for : , so . Option (B).

Trap: reading the output as the source voltage, 4 V (option C). The last source is not ideal at the output: it sits behind a resistor, and the node is also pulled down by the resistor to the rest of the network. We solved the three nodal equations with numpy and got , , = 1.250 V, 2.500 V and 3.000 V.

Where this shows up in industry

Nodal analysis of a resistive network with several sources is the routine way to predict the voltage that a sensor interface or a resistive ladder produces, and it is how circuit simulators solve the same problem for any size of network.

GATE 2023 · IN · Q.47NAT · 2 marksTransients in RC, RL and RLC circuits

Parallel R-L circuit, step current I0 u(t), initial inductor current I0/5: time to reach 99% of final value

The R-L circuit with and is excited by a step current . At , there is a current flowing through the inductor. The minimum time taken for the current through the inductor to reach of its final value is _____s (rounded off to two decimal places).
A current source I0 u(t) with arrow pointing up drives a resistor R in parallel with an inductor L. The inductor current I L is marked with an arrow pointing down through the inductor.I = I0 u(t)RLIL

Answer: Official key: 0.43 to 0.45

  1. A first order circuit follows . The inductor current cannot jump, so . A long time after the step the inductor is a short circuit for DC and carries all the source current: .
  2. The time constant of an R-L circuit is (the resistor in parallel with the source sees the same as in series): .
  3. .
  4. Set : , so and .

Trap: using zero initial current, which gives , or the rule of thumb of . The question gives a non-zero start, so the remaining gap to the final value is only and the settling is quicker. We also integrated numerically from and the current crossed at , matching the formula's .

Where this shows up in industry

Settling time of an inductive element sets how fast a coil, relay, solenoid or magnetic sensor reaches its working current after a step. The shortcut that 99% needs about 4.6 time constants, adjusted for the starting value, is used to choose the pulse width in driver circuits.

GATE 2024 · IN · Q.33NAT · 1 markTransients in RC, RL and RLC circuits

Switch opened at t = 0 in a 12 V circuit with 4 ohm, 0.25 H, 4 ohm and 0.1 F: dv_c/dt at t = 0+

The switch in the following figure has been closed for a long time (). It is opened at seconds. The value of at is __________ V/s (rounded off to nearest integer).
Circuit for Question 33. A 12 V source drives, through a 4 ohm resistor and a 0.25 henry inductor carrying current i L of t, a node. From that node a 4 ohm resistor in series with a switch (closed for t below 0, opened at t equals 0) goes back to the source return, and a 0.1 farad capacitor with voltage v c of t, plus on top, is connected in parallel with that branch+−12 V4 Ω0.25 HiL(t)4 Ωt = 0Switch0.1 Fvc(t)+−

Answer: Official key: 15 to 15

  1. Two rules decide a switching transient: an inductor current cannot jump, and a capacitor voltage cannot jump. So find and from the DC steady state, then use them just after the switch moves.
  2. Before (DC steady state): the inductor acts as a short circuit and the capacitor as an open circuit. The source sees the two resistors in series, so and .
  3. At the switch is open, so the branch carries no current. The inductor current stays at , and with the branch gone, all of it flows into the capacitor: .
  4. For a capacitor , so .

Trap: leaving the branch in the sum, which would give . That branch is removed by the open switch. We solved the DC circuit by nodal analysis (node voltage , inductor current ), then integrated the two state equations after switching with a fourth-order Runge-Kutta step: at is , and the state stays smooth afterwards.

Where this shows up in industry

The initial slope of a capacitor voltage after a switch operation tells a designer how fast a contact or relay output will ramp and whether a snubber or a filter capacitor is protecting a sensor input. The continuity rules for inductor current and capacitor voltage are the starting point for every switching-transient estimate.

GATE 2025 · IN · Q.63NAT · 2 marksTransients in RC, RL and RLC circuits

Switch across a 10 mA source opens at t = 0, 0.2 H inductor in network: i(t) in the 120 ohm branch at 2 ms

In the circuit shown, the switch is opened at . The current at is _____________ mA (rounded off to two decimal places).
A 10 mA current source pointing up is connected across a node pair. A switch that opens at t = 0 is wired in parallel with the current source. From the top node a 50 ohm resistor leads to a second node, from which a 120 ohm resistor goes down to the bottom, and a 40 ohm resistor, a 0.2 H inductor and another 40 ohm resistor form a series branch to the bottom rail. A 100 ohm resistor is in the bottom rail between the source and the 120 ohm resistor. The current i(t) is marked downward in the 120 ohm resistorSwitcht = 0 s10 mA50 Ω40 Ω100 Ω40 Ω0.2 H120 Ωi(t)

Answer: Official key: 4.60 to 5.00

  1. Before the switch is closed and it shorts the current source, so no source drives the rest of the circuit. The inductor current is zero before the switch opens, and an inductor current cannot jump, so .
  2. After the switch opens, all 10 mA flows through the 50 resistor into the node above the 120 resistor. There the current splits between the 120 resistor and the branch with 40 + 0.2 H + 40 (80 in total with the inductor). The 100 resistor carries the same 10 mA and does not change the split.
  3. Steady state (inductor like a short): current divider .
  4. Time constant . Seen from the inductor with the current source switched off (open circuit), the 50 and 100 resistors carry no current, so and .
  5. . The 120 resistor current is what is left of the 10 mA: .
  6. At : , inside the key range 4.60 to 5.00 mA.

Trap: counting the 50 and 100 resistors in the time constant. An ideal current source is an open circuit once it is turned off, so those two resistors are not in the inductor's loop. That slip gives and , outside the key. Another is to report the inductor current (5.19 mA) instead of the current in the 120 branch. We built the resistor network with nodal analysis, treated the inductor as a current source, integrated with a fourth-order Runge-Kutta method from to 2 ms, and got , the same as the closed form.

Where this shows up in industry

Opening a switch in a circuit with an inductor, such as a relay coil, a solenoid valve or a motor winding, starts a first-order current change set by the inductance and the resistance the coil sees. The time constant is how quickly an actuator reaches its steady current, and a source branch that is switched off drops out of that calculation.

From GATE prep to a instrumentation or electrical career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.