GATE Instrumentation (IN): Analog Electronics (diodes, BJT and MOSFET circuits, op-amps, instrumentation amplifiers, active filters, comparators and PLLs), previous-year questions solved

Every analog electronics question from the last five GATE Instrumentation Engineering papers, solved: diode and Zener circuits, BJT and MOSFET biasing and small-signal gain, op-amp amplifiers, integrators and instrumentation amplifiers, active filters, op-amp offset, bias current and output impedance, a comparator timing circuit and a phase-locked loop. Each answer matches the official key and was recomputed by code from a circuit model with the values printed in the paper.

Questions from official GATE IN papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 19 Nov 2026 · 14 of 29 questions on this page

GATE 2022 · IN · Q.31NAT · 1 markDiodes, BJT and MOSFET circuits

Zener 4 V regulator from 16 V through 1200 ohm, minimum Zener current 4 mA: maximum load current

A Zener diode is used as a 4 V voltage regulator in the circuit shown. Given that the diode requires a minimum current of 4 mA for voltage regulation, the maximum current (in milliamperes) permitted to flow through the load is ________ (round off to one decimal place)
A 16 V source in series with a 1200 ohm resistor feeds a node. A Zener diode (cathode at the node) and the load resistor R_L are both connected from that node to the bottom wire, in parallel with each other+−16 V1200 ΩZenerdiodeRL

Answer: Official key: 6.0 to 6.0

  1. In a Zener shunt regulator the series resistor carries one current, and that current splits between the Zener and the load. The node voltage is held at only while the Zener current stays above its minimum.
  2. Current in the series resistor: . It does not change with the load, because the node is held at 4 V.
  3. , so . The largest load current corresponds to the smallest allowed Zener current: .
  4. That is a load resistor no smaller than . Below that, the Zener drops out of regulation and the output falls.

Trap: subtracting the Zener voltage from nothing, or taking (all of the series current, so the Zener would carry zero). We swept the load current from 0 upward and kept the largest value with : 6.0 mA.

Where this shows up in industry

Zener shunt regulators give a cheap reference or a low-power supply rail in sensor interfaces, usually from a higher unregulated supply through a series resistor. The design check is always the worst case: the highest load current at the lowest supply voltage must still leave the Zener above its minimum current.

GATE 2022 · IN · Q.36MCQ · 2 marksDiodes, BJT and MOSFET circuits

Ideal diode into a 0.1 uF capacitor starting at 0.3 V, input peaks 0.4, 1.0, 0.6 V: Vout at 5 ms

A signal shown is applied from ms to ms to the circuit shown. Given the initial voltage across the capacitor is 0.3 V, and that the diode is ideal, the open circuit voltage at ms is ________
Left: the input voltage against time from 0 to 6 ms, with three positive peaks of about 0.4 V near 0.6 ms, 1.0 V near 2.9 ms and 0.6 V near 5 ms, and negative lobes between them. Right: the input goes through an ideal diode (anode on the input side) to the output node, which has a 0.1 microfarad capacitor to ground and nothing else connected1.00.60.40123456t (ms)Vin (V)Vin (t)Vout (t)0.1 μF
  1. (A)0.3 V
  2. (B)0.6 V
  3. (C)0.7 V
  4. (D)1.0 V

Answer: (D) Official key: D

  1. A diode in series with a capacitor, with nothing else on the output, is a peak detector. The ideal diode conducts only when the input is above the capacitor voltage, and the capacitor charges up to it. When the input falls, the diode switches off and the capacitor holds its value, because the output is open circuit and there is no resistor to discharge it.
  2. The capacitor starts at . The first positive peak, , is above it, so the capacitor rises to .
  3. The second peak, near 3 ms, reaches . The capacitor follows it up to and holds that value through the negative lobe.
  4. At the input is on its third lobe, at only about , below the stored , so the diode is off. . Option (D).

Trap: reading the instantaneous input at 5 ms (about 0.6 V, option B), or subtracting a 0.7 V diode drop (option C), which does not apply because the diode is ideal. We stepped the redrawn waveform through an ideal diode and capacitor model from 0.3 V and tested every option: only 1.0 V matches (1.00 V).

Where this shows up in industry

Peak detectors built from a diode and a capacitor read the amplitude of a vibration or ultrasonic signal and hold it for a slow converter to sample. Real circuits add a small bleed resistor or a reset switch so the held peak can fall again, and use a precision rectifier to remove the diode drop.

GATE 2022 · IN · Q.44MCQ · 2 marksDiodes, BJT and MOSFET circuits

Small-signal MOSFET with grounded gate, RL in the drain and RS in the source: impedance looking into node P

In the small signal circuit shown, the enhancement mode n-channel MOSFET is biased in saturation with transconductance . If channel length modulation is ignored, the small signal impedance looking into the node P is given by ________
An n-channel MOSFET with its gate connected to ground and its body tied to its source. The drain goes up through R_L to a supply rail that is at ground for the small signal. The source goes down through R_S to the GND rail. The node P is the source terminalRL PRS GND
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (B) Official key: B

  1. Put a test current into node P and find the voltage it produces. The gate is held at small-signal ground, so this is a common-gate stage seen from the source.
  2. The channel current from drain to source is : a rising source voltage reduces the current, like a resistor of from P to ground.
  3. At node P: , which gives .
  4. does not appear: with channel length modulation ignored, the drain is an ideal current source and the voltage across cannot feed back to the source. Option (B).

Trap: adding because it is in the same branch, as in (A) or (C). With sample values , , the nodal model gives 200.0 , which equals and none of the other three.

Where this shows up in industry

The low impedance seen looking into a MOSFET source is why common-gate stages are used as the input of high-frequency and photodiode amplifiers, where a low input resistance keeps the input node moving very little. Source degeneration with a resistor, as here, trades some of that for linearity and bias stability.

GATE 2022 · IN · Q.47MCQ · 2 marksDiodes, BJT and MOSFET circuits

Small-signal MOSFET with three R0 resistors, signal vd injected at the supply: gain vo/vd

In the small signal circuit shown, the enhancement mode n-channel MOSFET is biased in saturation with a transconductance . A small signal low-frequency voltage injected at the supply terminal results in a small signal voltage fluctuation at the output. If the channel length modulation of the MOSFET is ignored, the small signal gain is given by ________
An n-channel MOSFET with its source and body at the GND rail. The supply v_d connects through a resistor R_0 to the drain, which is the output v_o. A second R_0 joins the drain to the gate, and a third R_0 joins the gate to groundvd R0 vo R0 R0 GND
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (D) Official key: D

  1. Write the small-signal node equations. The source is at ground, so the channel current is , drawn from the drain. The gate draws no current.
  2. Gate node: the resistor to the drain and the resistor to ground carry the same current, so (a divider of two equal resistors).
  3. Drain node: the current arriving through the top from leaves through the gate divider (current ) and the channel: .
  4. Multiply by : , so .
  5. . Option (D).

Trap: forgetting the current that flows down the gate divider, which gives (the becomes 1). With the nodal model gives , which equals and none of the other three options.

Where this shows up in industry

Supply-to-output gain is the supply-rejection behaviour of an amplifier: any ripple on the rail leaks to the output by this factor. Designers check it for sensor front ends powered from noisy switching supplies, and add decoupling or a regulator when the number is too large.

GATE 2022 · IN · Q.58NAT · 2 marksDiodes, BJT and MOSFET circuits

NPN BJT with R1 = 100 kohm from collector to base and R2 = 1 kohm, VCE = 5.2 V: current gain beta

In the circuit shown, and . If the base-to-emitter voltage of the npn BJT is 0.7 V and the collector-to-emitter voltage is 5.2 V, the (current gain) of the BJT is ________ (round off to two decimal places)
An NPN transistor with its emitter at ground. A resistor R_2 joins the 12 V supply to the collector. A resistor R_1 joins the collector to the base12 VR2 R1 GND

Answer: Official key: 148.00 to 152.00

  1. The emitter is at ground, so the collector is at and the base is at .
  2. joins collector to base, so it carries the base current: .
  3. carries the current from the supply to the collector node: .
  4. At the collector node this current is the sum of the collector current and the current that goes round through into the base: .
  5. .

Trap: taking and ignoring the base current in the node equation gives 151.11, which falls inside the key range but is not what the circuit says. The exact node balance gives 150.11. We solved the two node equations in code from the stated voltages.

Where this shows up in industry

Collector-to-base feedback bias is a simple way to stabilise a transistor stage: if beta rises, the collector falls and takes base current away. Measuring beta this way, from the voltages and currents in a working circuit, is how a transistor is checked on the bench.

GATE 2022 · IN · Q.62NAT · 2 marksDiodes, BJT and MOSFET circuits

Capacitor charged to 10 V, ideal diode and 1 mH inductor, switch closed at t = 0: capacitor voltage at 0.5 s

In the circuit shown, the capacitance and inductance and the diode is ideal. The capacitor is initially charged to 10 V and the current in the inductor is initially zero. If the switch is closed at s, the voltage (in volts) across the capacitor at s is ______ (round off to one decimal place)
A series loop. A capacitor C_0, charged with its top plate positive, a switch that closes at t = 0, an ideal diode with its anode on the switch side, and an inductor L_0, joined in a ringt = 0Ideal diode+−Vc (t)C0 L0

Answer: Official key: -10.1 to -9.9

  1. Without the diode, a capacitor and an inductor ring forever: with . The ideal diode lets current flow in one direction only (from the capacitor's positive plate through the inductor), so it stops the ringing after a half cycle.
  2. , so the half period is .
  3. During that half cycle the capacitor discharges to 0 V (when the current peaks at ) and then charges the other way to as the inductor current decays to zero.
  4. At that instant the current would try to reverse, and the ideal diode blocks it. With no path left, the capacitor keeps its charge: for all later time, including , which is more than a thousand half periods later.

Trap: ignoring the diode and evaluating . The diode is the whole point of the question. We integrated the loop with the inductor current clamped at zero (diode off) and got after the half cycle, and it stays there.

Where this shows up in industry

A diode in series with an LC circuit is the idea behind resonant charging and commutation circuits: the diode traps the charge once it has been transferred, so a capacitor can be charged to about twice a source voltage or reversed. Snubbers and pulse circuits in power electronics use the same trick.

GATE 2023 · IN · Q.33NAT · 1 markDiodes, BJT and MOSFET circuits

Ideal diode across a current source of pi sin(3000 pi t) mA: average current through resistor R

The diode in the circuit is ideal. The current source is mA. The magnitude of the average current flowing through the resistor R is ______mA (rounded off to two decimal places).
Current source in parallel with a diode, the diode pointing from the top node to the bottom node, and a resistor R in parallel with the diodeis (t)RD

Answer: Official key: 0.95 to 1.05

  1. The source forces its current into the parallel pair of diode and resistor. An ideal diode is a short circuit when forward biased and an open circuit when reverse biased, so the current has to pick a path.
  2. Positive half-cycle: the source current points into the top node. The diode points from the top node to the bottom node, so it conducts and shorts the resistor. Resistor current .
  3. Negative half-cycle: the source now pulls current out of the top node. The diode would have to conduct upwards, which it cannot, so it is open and the whole source current goes through (with a negative sign).
  4. So carries only the negative half-sine of peak . The average of one half-sine over a full period is .
  5. . The source frequency, 1.5 kHz, does not matter, and neither does .

Trap: using the full-wave average , or . We swept one period in code with an ideal diode switching on the sign of the source current and averaged the resistor current: 1.00 mA.

Where this shows up in industry

A diode that steers a current to one side of a load is the heart of half-wave rectifiers, clamps and protection circuits on sensor lines. The same question, 'what carries the current in each half-cycle', is how you estimate the average value a meter or ADC will see after a rectifier stage.

GATE 2023 · IN · Q.56NAT · 2 marksDiodes, BJT and MOSFET circuits

nMOS amplifier, muCox 1 mA/V2, VT 1 V, W/L 2, drain bias 4 V, 1 kohm source resistor: Vout/Vin

The figure below shows a feedback amplifier constructed using an nMOS transistor. Assume that , threshold voltage and . The bias voltage at the drain terminal is 4 V. The capacitors offer zero impedance at the signal frequency. The ratio is _____________(rounded off to two decimal places).
nMOS amplifier: gate bias from 200 kilo-ohm and 300 kilo-ohm divider on 5 volts, 1 kilo-ohm drain resistor to the supply, 1 kilo-ohm source resistor, output taken from the source through a capacitorVDD = 5 VR1 = 200 kΩR2 = 300 kΩRD = 1 kΩRS = 1 kΩVout C∞Vin C∞W/L = 2

Answer: Official key: 0.64 to 0.70

  1. First the dc bias. The gate divider gives .
  2. The drain sits at 4 V, so the drain current is . That gives and , so the overdrive is .
  3. Check the square law: . It matches, and , so the transistor is in saturation.
  4. Transconductance: .
  5. The signal enters at the gate and leaves at the source. The drain is held at the supply for signals (the 1 kΩ resistor there is not the output), so this is a source follower. The source resistor feeds back: .
  6. 0.67.

Trap: stopping at , or taking (forgetting the drop across ), which gives and a gain of 0.80. Both fall outside 0.64 to 0.70. We solved the nonlinear dc bias with the square-law model (drain at 4.000 V), then differentiated the source voltage against the gate voltage numerically: 0.667.

Where this shows up in industry

Source followers and emitter followers buffer a high-impedance sensor or electrode so that cable and ADC input capacitance does not load it. Their gain is just under one, and the source resistor that sets that gain also stabilises the bias against transistor spread.

GATE 2024 · IN · Q.23NAT · 1 markDiodes, BJT and MOSFET circuits

Op-amp comparator output limited by a 1.8 V Zener for a CMOS input, minimum 2 mA: maximum RZ

Consider the circuit shown in the figure. The CMOS digital logic circuit has infinite input impedance. Assume the opamp is ideal. A 1.8 V Zener diode with a minimum Zener current of 2 mA is used. The corresponding maximum value of resistance is ________ k. (rounded off to one decimal place).
A comparator with supplies of plus and minus 5 volts, inputs Vin and VREF, drives a resistor RZ. The resistor feeds the node Vout, which has a 1.8 volt Zener diode to ground and goes to the input of a CMOS digital logic block powered from 1.8 volts.VinVREF+−5 V−5 VRZVoutCMOSDigital Logic1.8 V

Answer: Official key: 1.6 to 1.6

  1. The op-amp has no feedback, so it is a comparator. An ideal one swings its output to the supply rail, so with the output high it sits at .
  2. The 1.8 V Zener holds the node at 1.8 V so the 1.8 V CMOS gate is never given more than its own supply. A Zener only regulates while the current through it stays at or above its minimum, .
  3. The CMOS input has infinite impedance, so it draws no current. All of the current through flows into the Zener: .
  4. falls as rises, so the largest allowed is the one that gives exactly the minimum current: .
  5. .

Trap: dividing the full 5 V by 2 mA gives 2.5 k and forgets that 1.8 V of the 5 V is already across the Zener, not across . We swept in code, computed for each, and found by bisection that falls to 2 mA at 1.6 k and no larger value keeps the Zener regulating.

Where this shows up in industry

A Zener clamp behind an op-amp comparator is a cheap way to turn a plus and minus supply comparator output into a safe logic level for a low-voltage microcontroller input. The series resistor must be small enough that the Zener always keeps its minimum current across the supply range and temperature, and large enough that it does not overheat.

GATE 2024 · IN · Q.24NAT · 1 markDiodes, BJT and MOSFET circuits

NMOS amplifier with 100 kilo-ohm drain-gate feedback, 3.3 kilo-ohm load, 3.3 V supply: drain current

Figure shows an amplifier using an NMOS transistor. Assume that the transistor is in saturation with device parameters, , threshold voltage and . Ignore the channel length modulation effect. The drain current of the transistor at the operating point is _________ A (rounded off to nearest integer).
An NMOS amplifier. A 3.3 volt supply feeds the drain through a 3.3 kilo-ohm resistor. A 100 kilo-ohm resistor joins the drain to the gate. The source is grounded. Large capacitors couple the input to the gate and the drain to the output.3.3 VRD = 3.3 kΩ100 kΩVinClargeVoutClarge

Answer: Official key: 498 to 502

  1. For DC analysis, open-circuit every capacitor: the large coupling capacitors block DC, so the only DC paths are the supply, the 3.3 k resistor, the transistor and the 100 k feedback resistor.
  2. The gate draws no current, so no current flows in the 100 k resistor and there is no voltage drop across it. The gate voltage equals the drain voltage: . Then always holds, so the device is in saturation, as the question states.
  3. Saturation current: .
  4. Load line: .
  5. Substitute and solve the quadratic in : the roots are 500 A and 1290 A. The larger root would put , below , so the transistor would be off and the root is rejected.
  6. , with . Check: .

Trap: using the full 3.3 V supply as gives 3.5 mA, far above what the 3.3 k resistor can carry. The gate sits at , not at the supply.

Where this shows up in industry

Connecting a resistor from drain to gate is a standard way to self-bias a single MOSFET amplifier, because the feedback holds the operating point near the middle of the supply even when the threshold varies from part to part. The same trick sets the quiescent point of the first stage in many low-cost sensor preamplifiers.

GATE 2025 · IN · Q.35NAT · 1 markDiodes, BJT and MOSFET circuits

BJT with very high beta, Zener base reference 4.7 V and 1 kilohm emitter resistor: LED current in mA

In the circuit shown, assume that the BJT in the circuit has very high and V, and the Zener diode has V. The current through the LED is ___________ mA (rounded off to two decimal places).
BJT circuit: 12 V supply, 2.2 kilohm resistor R1 to the base, a 4.7 V Zener from base to ground, an LED in the collector and a 1 kilohm emitter resistor to groundVCC = 12 VR12.2 kΩVZ = 4.7 VLEDIRE1 kΩVBE +−

Answer: Official key: 3.90 to 4.10

  1. The Zener diode, fed through , sits in breakdown and holds the base at . The transistor therefore acts as a constant-current sink, set by the emitter resistor.
  2. Emitter voltage: .
  3. Emitter current: .
  4. With very high the base current is negligible, so , and the LED current is 4.00 mA.
  5. Check the Zener: the current through is , well above the base current, so the Zener stays in breakdown. The LED drop (about 2 V) leaves the collector near 10 V, above the base, so the transistor stays in the active region.

Trap: trying to use to find the LED current. only biases the Zener. Even with a finite the current changes only to 3.96 mA, inside the key range of 3.90 to 4.10 mA. We solved the bias with a very large , checked the Zener current and the active-region condition, and confirmed the value is inside the key range.

Where this shows up in industry

A Zener-referenced transistor current sink drives indicator LEDs, relay coils and sensor bias loops at a steady current while the supply varies. The emitter resistor sets the current and the transistor's gain barely matters.

GATE 2026 · IN · Q.21MCQ · 1 markDiodes, BJT and MOSFET circuits

A common gate MOSFET amplifier represents which type of controlled source

A common gate amplifier represents a _____________.
  1. (A)voltage controlled voltage source
  2. (B)current controlled current source
  3. (C)voltage controlled current source
  4. (D)current controlled voltage source

Answer: (B) Official key: B

  1. In a common gate stage the gate is held at signal ground, the input goes into the source and the output is taken at the drain.
  2. The drain current is almost exactly the current pushed into the source, so the current gain is close to . The input resistance seen at the source is only about (low, here 0.20 k for ), which means the stage wants to be driven by a current, not a voltage.
  3. The output is the drain of a transistor with a high output resistance , so it behaves as a current source: the current it delivers does not depend on the load.
  4. An ideal controlled source is one whose gain does not change with the source or load around it. A current in, current out stage with low input and high output resistance is a current controlled current source, the current buffer. Option (B).

Trap: the common source stage is the voltage controlled current source (high input resistance, drain current ); picking (C) mixes the two up. We solved the small-signal stage for nine combinations of source resistance (20 k to 1 M, well above , as a current source should be) and load (1 to 20 k) and tested the four gains: only the current gain stayed constant (spread 1.0%, mean -1.00); the other three varied by 220% or more.

Where this shows up in industry

A common gate stage is used as the cascode device and as a low-input-impedance current buffer in sensor and photodiode front ends and in RF amplifiers. Putting it above a common source stage keeps the drain voltage of that stage nearly fixed, which gives a higher output resistance and wider bandwidth.

GATE 2026 · IN · Q.22MCQ · 1 markDiodes, BJT and MOSFET circuits

BJT bias circuit with beta 100 and VBE 0.65 V, 5 V supply, all resistors 5 kilohm: quiescent collector current

In the circuit shown, the BJT has a of 100. The base-emitter junction voltage is 0.65 V. The quiescent collector current, is _______ mA.
BJT bias circuit: a 5 V supply feeds a 5 kilohm base divider (5 kilohm to the supply, 5 kilohm to ground) and a 5 kilohm collector resistor; the emitter returns to ground through 5 kilohm; the collector current IC flows down through the collector resistor.5 V5 kΩ5 kΩ5 kΩ5 kΩIC
  1. (A)0.365
  2. (B)0.435
  3. (C)0.625
  4. (D)0.862

Answer: (A) Official key: A

  1. This is a voltage-divider bias circuit. Replace the base network by its Thevenin equivalent: and .
  2. Write the base-emitter loop. The emitter current is , so .
  3. .
  4. . Option (A).
  5. Check the region: and , so the collector is well above the base: the transistor is in the active region and the equations hold.

Trap: ignoring the base current (taking ) gives , close to the answer but not an option. We solved the loop and tested each option; only 0.365 mA matches to 0.5%.

Where this shows up in industry

Voltage-divider bias with an emitter resistor is the standard way to set the operating point of a discrete transistor stage, because the emitter resistor feeds back and keeps the collector current steady when beta or temperature changes. Instrument preamplifiers and sensor drivers are biased this way before any signal is applied.

GATE 2026 · IN · Q.34NAT · 1 markDiodes, BJT and MOSFET circuits

15 cos wt source, 4 ohm, then a 3 V Zener in series with 8 ohm: maximum value of the output voltage

In the circuit below the maximum value of is ________ V. (rounded off to the nearest integer)
A source 15 cos omega t drives a 4 ohm resistor; after it a 3 V Zener diode (cathode up) in series with an 8 ohm resistor to the return wire; the output voltage vout is taken across the Zener and the 8 ohm resistor together.15 cos ωt4 Ω3 V8 Ω+−vout

Answer: Official key: 11 to 11

  1. The Zener diode is drawn with its cathode (bent bar) at the top. For a positive source voltage it is reverse biased, and once the voltage across it reaches it breaks down and holds exactly . For a negative source voltage it is forward biased and drops about (ideal).
  2. The output is taken across the Zener and the resistor together, so the maximum occurs at the positive peak of the source, .
  3. At the peak the Zener is in breakdown, so the current is set by the part of the source above the Zener voltage: .
  4. .

Trap: stopping at the Zener voltage () forgets the drop across the series ; ignoring the Zener altogether and using the divider gives . We swept one full cycle of the source through the ideal-Zener model and read the maximum of : 11 V.

Where this shows up in industry

Zener diodes in series with a resistor set reference voltages and clamp sensor inputs against over-voltage. The series resistor limits the breakdown current, which is why the current, not only the Zener voltage, decides the output in a clamp like this.

From GATE prep to a instrumentation or electronics hardware career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.