GATE Instrumentation (IN): Electricity and Magnetism (Gauss's law, capacitance, magnetic force, Faraday's law), previous-year questions solved

Every electricity and magnetism question from the last five GATE Instrumentation Engineering papers, solved: the field of a charge sheet in a dielectric, capacitance of concentric spheres, charge density from the divergence of a field, work done moving a charge, current from a non-uniform current density, the force between parallel conductors, the force on a wire or a sliding bar in a magnetic field, and the current induced in a rotating loop. Each answer matches the official key and was recomputed by code with the values printed in the paper.

Questions from official GATE IN papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 19 Nov 2026 · 10 questions

GATE 2022 · IN · Q.59NAT · 2 marksElectrostatics: fields, potential and capacitance

Spherical capacitor with air dielectric, inner radius 10 cm, outer radius 15 cm: capacitance in picofarads

A capacitor is constructed using two concentric spheres and air as the dielectric medium (permittivity of air ). The radii of the inner and outer spheres are and , respectively. The capacitance (in picofarads) is ______ (round off to 2 decimal places)

Answer: Official key: 32.8 to 33.9

  1. Capacitance is stored charge divided by the voltage across the plates, . Put charge on the inner sphere and on the outer one.
  2. Gauss's law with a spherical surface of radius between the shells: the flux through it is , so , pointing outwards, exactly like the field of a point charge.
  3. The voltage between the shells is the line integral of the field from the inner to the outer sphere: .
  4. .
  5. .

Trap: using the parallel-plate formula with the inner sphere area gives , which is too low because the plates are curved and the outer one is larger. Do not forget to convert centimetres to metres. We integrated the field numerically between the shells for a charge of 1 nC and divided: (the voltage came out at ), matching the formula.

Where this shows up in industry

Spherical and cylindrical geometries come up in guarded probes, coaxial cables and level or proximity sensors, where the capacitance between two curved electrodes is the measured quantity. The capacitance grows quickly as the gap between the electrodes shrinks, which is why a thin gap gives a sensitive probe.

GATE 2024 · IN · Q.20MCQ · 1 markElectrostatics: fields, potential and capacitance

Capacitance between two concentric spherical metal shells of radii x and y, with y greater than x

The capacitance formed between two concentric spherical metal shells having radii and with is
Note: is the permittivity of the medium between the shells.
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. Capacitance is : put charge on the inner shell (radius ) and on the outer shell (radius ), then find the voltage between them.
  2. Gauss' law with a spherical surface of radius between the shells encloses only , so and pointing radially outwards. Outside the outer shell the enclosed charge is zero, so there is no field there.
  3. The potential difference is the line integral of the field from the inner to the outer shell: .
  4. . Option (A).

Check: as this tends to , the capacitance of a single isolated sphere, which is the right limit. Options (B) and (C) do not have the symmetry between and that the physics demands. We also integrated the Gauss-law field numerically for three radius pairs, for example and in air, which gives , and only option (A) matched every pair.

Where this shows up in industry

Spherical and coaxial capacitor formulas are used to estimate stray capacitance of probe tips, guard electrodes and cable shields in sensitive instrumentation. A coaxial or concentric layout is also how a capacitive level or pressure sensor gets a well-defined, repeatable capacitance.

GATE 2025 · IN · Q.19MCQ · 1 markElectrostatics: fields, potential and capacitance

Flux density at P(0, 0, 5) from an infinite 10 C/m^2 sheet on z = 0 in a medium of relative permittivity 10

An infinite sheet of uniform charge is placed on plane. The medium surrounding the sheet has a relative permittivity of 10. The electric flux density, in C/m2, at a point , is
Note: , , and are unit vectors along the , , and directions, respectively.
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. Gauss' law for a sheet: draw a small pillbox that straddles the sheet, with flat faces of area parallel to it. By symmetry the flux density points away from the sheet (a positive charge), is the same size on both sides and has no sideways part, so flux leaves through the two flat faces only: .
  2. So , with no dependence on the distance from the sheet.
  3. The permittivity does not appear. The dielectric changes the electric field, , but is set by the free charge alone. This is the reason the relative permittivity of 10 is a distraction here.
  4. The point lies above the sheet (), so points along : . Option (A).

Trap: option (C), , forgets that the flux splits between the two sides, and option (D), , divides by the relative permittivity as if were . As a check we summed the field of a uniformly charged disc on its axis at with the radius pushed to (so effectively infinite) and multiplied by : that gives , and along on the other side of the sheet.

Where this shows up in industry

Parallel-plate and guard-ring capacitive sensors are modelled as large charged sheets, and the flux density between the plates is set by the surface charge, whatever dielectric fills the gap. That is why the charge on a capacitive probe is a clean measure of the applied voltage while the dielectric only changes the field and the stored energy.

GATE 2026 · IN · Q.32NAT · 1 markElectrostatics: fields, potential and capacitance

Potential difference v_A - v_B = 5 V: work done moving a charge of 1 coulomb from B to A

The potential difference between nodes and in a circuit is . The work done in moving a charge of from point to is ____ J. (answer in integer)

Answer: Official key: 5 to 5

  1. Electric potential is energy per unit charge. The work done against the field to move a charge from point to point is .
  2. means is at the higher potential, so moving a positive charge from up to needs energy supplied from outside.
  3. .

Trap: the direction. Moving the charge from to is a drop of 5 V and gives back , so the sign depends on which way you go. We checked it with a uniform field of 50 V/m: at , at gives , and integrating the force that must be applied to a 1 C charge from to gave 5.000 J.

Where this shows up in industry

Potential difference is what every voltage measurement reports, and the energy needed to move charge across it is why a source delivering a current through a drop of a few volts must supply real power. It is the basis for working out the power budget of any sensor loop.

GATE 2026 · IN · Q.37MCQ · 2 marksElectrostatics: fields, potential and capacitance

Electric field E = (2x+5y+6z)i + (5x+4y+10z)j + (6x+10y+2z)k V/m in free space: the charge density

An electric field in free space is
.
The charge density is ____ C/m. ( is the permittivity of free space)
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. Gauss' law in point form: the divergence of the electric flux density equals the free charge density, . In free space , so .
  2. Divergence is . Only the terms that carry the matching variable count: , , .
  3. , so . Option (A).

Trap: adding all the coefficients, or including the cross terms such as or . Those only matter for the curl, and here they cancel in pairs (), so the field is electrostatic. We computed the outward flux of through a cube of side 0.2 m numerically and divided by its volume: , matching only option (A).

Where this shows up in industry

Charge density from a measured field is how engineers locate trapped or stray charge, for example in electrostatic precipitators, insulation testing and capacitive level or proximity sensors where the field around the electrodes is mapped.

GATE 2022 · IN · Q.57NAT · 2 marksMagnetic fields, forces and induction

Semicircular loop, R = 0.1 m, 20 rad/s, in B = 2 T for x >= 0, loop resistance 2 ohm: peak-to-peak current

A conducting semi-circular loop of radius , with its diameter centered at the origin, rotates in the - plane about the origin with a constant angular velocity, , as shown. A magnetic field of magnitude and normal to - plane exists in the region as shown. If the loop has a resistance of , and negligible inductance, the peak-to-peak current (in milliamperes) in the loop is ______ (round off to one decimal place)
The x-y plane with a magnetic field B pointing into the page, shown as crosses, in the region x greater than or equal to 0 only. A semicircular conducting loop of radius R has its diameter through the origin and rotates counterclockwise about the origin with angular velocity omegaxyB(0, 0)Rω

Answer: Official key: 200.0 to 200.0

  1. Faraday's law: the induced emf is the rate of change of the flux linked by the loop, . The flux is times the area of the loop that lies inside the field region .
  2. The loop is a half-disc of area whose edge sweeps an angle . The part inside is a sector whose angle changes at the rotation rate: , with . Over each half revolution the angle inside first grows from 0 to and then falls back to 0: a triangular flux, with a constant slope that flips sign.
  3. , and (negligible inductance, so ).
  4. A constant slope that reverses means the current is a square wave between and . The peak-to-peak value is .

Trap: giving the amplitude, , as the answer to a peak-to-peak question, or treating the emf as a sinusoid (it is not: the flux is a triangle wave, so the current is flat-topped). We computed the flux numerically over one revolution () with the overlap angle checked by brute-force angle sampling, differentiated it, and divided by : the current was , so peak to peak.

Where this shows up in industry

A coil turning in a magnetic field produces an emf proportional to rotation rate, which is the principle of tacho-generators and many speed sensors. How the coil enters and leaves the field sets the waveform, so a field that covers only part of the turn gives a flat-topped output instead of a sine wave.

GATE 2023 · IN · Q.27NAT · 1 markMagnetic fields, forces and induction

Two infinitely long parallel conductors: force per unit length is 10 uN/m at 2 cm, find it at 4 cm

The force per unit length between two infinitely long parallel conductors, with a gap of 2 cm between them is 10 N/m. When the gap is doubled, the force per unit length will be __________ N/m (rounded off to one decimal place).

Answer: Official key: 4.9 to 5.1

  1. Ampere's law gives the field of a long straight conductor carrying at a distance : . The Lorentz force on a length of the second conductor, carrying at right angles to this field, is .
  2. Force per unit length: . With the currents and the medium unchanged, everything except is fixed, so the force per unit length varies as .
  3. Doubling the gap from to halves the force per unit length: .
  4. .

Trap: using an inverse-square law, as for point charges or point sources. That law applies in three dimensions; a conductor of infinite length makes the field fall as only, so the answer is not . We evaluated with a current product that gives at () and got at .

Where this shows up in industry

Closely spaced current-carrying conductors push on each other, and the force scales with the inverse of the spacing. Busbar designers use this to size the supports that stop bars from moving during a short circuit, and the same relation once defined the ampere in the SI system.

GATE 2024 · IN · Q.36MCQ · 2 marksMagnetic fields, forces and induction

Total current in a round wire of radius a when the current density is J = k s^2 (s is the radial distance)

A wire of circular cross section with radius is shown in the figure. The current density is given by , where is a constant, is the radial distance from the axis and . The total current in the wire is
A long straight wire of circular cross-section with radius a, drawn as a cylinder with a shaded end face, a dotted axis along its length, and an arrow marked I showing the current flowing along the axisaAxisI
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. Current is the flux of current density through the cross-section: . Because changes with the radius, it cannot be pulled out of the integral as .
  2. Slice the circular face into thin rings of radius and width . Each ring has area and carries the same all the way round, so .
  3. . Option (A).

Trap: option (D), , comes from forgetting the factor of 2 in (using ), and options (B) and (C) have the wrong power of . Dimensions give a quick check: has units of A/m, so is in amperes. We also summed 200 000 thin rings numerically for three pairs of and (for example , gives , and ), and only option (A) matched all three.

Where this shows up in industry

Current density that is not uniform across a conductor appears with skin effect at high frequency and in thick bus bars, and it is why a resistance or inductance estimate that assumes uniform current can be off. The ring-by-ring integral is the standard way to get a total from a measured or modelled profile.

GATE 2025 · IN · Q.30MCQ · 1 markMagnetic fields, forces and induction

Force on a bar on rails the instant a 60 V source (0.5 ohm internal) is switched on, B = 0.5 T, l = 1 m

A 60 V DC source with an internal resistance is connected through a switch to a pair of infinitely long rails separated by as shown in the figure. The rails are placed in a constant, uniform magnetic field of flux density , directed into the page. A conducting bar placed on these rails is free to move. At the instant of closing the switch, the force induced on the bar is
Note: Assume there is no friction between the bar and the rails. The resistances of the conducting bar and the rails are zero.
A 60 V source (plus at the top) in series with a 0.5 ohm internal resistance and a switch feeds two horizontal rails 1 m apart. A conducting bar lies across the rails and can slide to the right, the positive x direction. A uniform magnetic field of 0.5 T points into the page, shown by crosses. The rails continue to infinity to the right+−60 VRint = 0.5 ΩSwitch×××××××××××××××××××lx̂B = 0.5 T, into the pageConducting barRails of infinite length
  1. (A)60 N in the direction of
  2. (B)60 N opposite to the direction of
  3. (C)120 N in the direction of
  4. (D)120 N opposite to the direction of

Answer: (A) Official key: A

  1. At the instant the switch closes the bar is still at rest, so it has not yet produced any motional emf (). The only resistance in the loop is the internal resistance of the source, because the bar and rails have none.
  2. Current: .
  3. Lorentz force on a straight conductor: , magnitude .
  4. Direction: the positive terminal of the source is at the top, so the current leaves it, goes along the top rail and runs down the bar (the direction); the field is into the page (). Then , so the force pushes the bar to the right, in the direction of (the right-hand rule on the fingers pointing down the bar, curling into the page, gives the thumb to the right).
  5. The force is 60 N in the direction of . Option (A).

Trap: option (C), 120 N, uses the current in amperes as if it were the force. Option (B) and (D) have the wrong direction, from reversing the source polarity. As the bar speeds up, its motional emf opposes the 60 V and the force falls to zero when the bar reaches . We checked the force with a numerical cross product for the current direction and field read from the figure: , and only option (A) matched.

Where this shows up in industry

This is the working principle of a linear motor or rail actuator, and the same force law underlies moving-coil meters, loudspeaker voice coils and electromagnetic flow meters. At switch-on the current is limited only by the supply and its internal resistance, so real drives limit it to protect the source.

GATE 2026 · IN · Q.38MCQ · 2 marksMagnetic fields, forces and induction

Wire carrying 1 A along (i + 2j + k)/sqrt(6) in B = 2i + 2k T: the force per unit length on the wire

A straight thin wire carrying a current of in the direction
is placed inside a magnetic field of .
The force per unit length on the wire is _____ N/m.
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (C) Official key: C

  1. Lorentz force on a current element: . Per unit length of wire, , a cross product, so the force is perpendicular to both the wire and the field.
  2. Take and . The cross product has components .
  3. . Option (C).

Trap: option (A) has the right direction but the factor of the unit vector is lost. A magnitude check helps: the sine of the angle between and gives . We computed with numpy and tested each option: only (C) matched, and the force is perpendicular to both (dot product 0.0) and (dot product 0.0).

Where this shows up in industry

The force on a current-carrying conductor in a magnetic field is the working principle of moving-coil meters, loudspeakers, voice-coil actuators and the force sensors that balance a current against a known field. Getting the direction and the unit-vector scaling right decides whether a coil deflects the way an instrument expects.

From GATE prep to a instrumentation, sensors or electrical design career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.