GATE Instrumentation (IN): Digital Electronics (logic gates and families, Boolean minimisation, multiplexers, flip-flops and counters, ADCs and DACs, microprocessors), previous-year questions solved, part 2
Part 2 of 2 of the Digital Electronics hub: 10 more official GATE IN questions on ADCs, DACs and data acquisition and microprocessors and embedded systems, each solved step by step and checked against the official answer key. Part 1 covers number systems, logic gates and IC families and combinational and sequential circuits.
Questions from official GATE IN papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 19 Nov 2026 · 10 of 27 questions on this page
ADC with 0.01 V resolution covering 0 V to 10 V: minimum number of output bits
Answer: bits Official key: 10 to 10
- An -bit converter has output codes. Its step size (the resolution, one least significant bit) over a span is when code 0 is 0 V and the top code is the full-scale voltage.
- The span is and the step must be no larger than , so we need at least distinct codes.
- codes gives a step of , too coarse. codes gives , which is finer than .
- Minimum number of bits: .
Trap: computing bits, which mixes up the voltage span with the number of levels. We solved for the smallest with and confirmed that 9 bits misses the 0.01 V resolution while 10 bits meets it.
Data-acquisition cards are specified by resolution against full scale: a 10-bit converter on a 10 V range resolves about 10 mV, which suits a thermocouple amplifier output but not a precision load cell. Picking the bit count from the smallest change you must see is the first step in choosing a converter.
Resistor ladder DAC with 4 V reference and switches A, B, C set as shown: Thevenin Vth and Rth at the output
- (A)
- (B)
- (C)
- (D)
Answer: (C) Official key: C
- Read the switch states: A and C are connected to ground, B is connected to the 4 V reference. The digital word is . Find the Thevenin equivalent by working along the ladder from the left, replacing each section with its Thevenin equivalent.
- At node A: the left-hand to ground and the switch-A rung (also to ground) are in parallel: . Add the series to reach node B: to ground.
- At node B, that to ground faces the rung to . Thevenin: , .
- Add the next series : behind at node C.
- At node C, the rung goes to ground (switch C is on ground). Thevenin: and . Option (C).
- Check with the binary weights: with this ladder , so only high gives , while only high would give 2 V.
Trap: reading switch B as ground and C as the reference gives 2 V, and forgetting that the output resistance is the whole ladder with the reference shorted () gives 2 k. We solved the ladder by nodal analysis for the open-circuit voltage and, with the reference shorted, for the resistance with 1 A injected: 1.000 V and 1000 ; all eight switch codes agreed with the binary-weighted formula.
Ladder DACs set the output of data-acquisition and waveform-generator boards. The Thevenin resistance matters in practice because it forms a divider with whatever load the DAC drives, so a buffer is normally placed after it.
ADC with 1.4 V full scale and 200 mV resolution, 500 MHz input at Nyquist rate: serial data rate
Answer: Official key: 3 to 3
- Resolution (one step, or LSB) is the full-scale range divided by the number of steps. An -bit ADC has codes and steps between the first and last, so .
- Number of steps . Then , so and bits (codes 0 to 7).
- The Nyquist sampling rate is twice the signal bandwidth: .
- The parallel-to-serial converter must send all bits of every sample in one sample period, so the serial rate is . Answer 3.
Trap: reading the 7 steps as 7 bits gives 7 Gbps. Seven is the number of steps, not the number of bits; the bit count is . We checked every bit count from 1 to 16 and only gives a 200 mV step for a 1.4 V full scale.
Sampling rate times bits per sample is the first number to check when sizing a high-speed data link: it sets the serial lane speed on an oscilloscope front end, a software-defined radio or an ultrasound system. Low-resolution, very fast converters like this are common where bandwidth matters more than precision.
Dual-slope ADC, 100 ms integration, 5 V reference, 1.25 V input: total time taken
Answer: Official key: 125 to 125
- A dual-slope ADC works in two phases. In the first it integrates the unknown input for a fixed time . In the second it connects the opposite-polarity reference and integrates back to zero, taking time . Charge gained equals charge removed.
- Charge balance: , so . and cancel, which is why this converter is so accurate.
- .
- The time taken by the ADC for the whole measurement is the sum of the two phases: . The official key is exactly 125 ms.
Trap: giving only the run-down time, 25 ms. The question asks for the time taken to measure, and the integration phase is part of it. We computed both phases from the charge balance and checked the total against the key range of 125 to 125 ms.
Dual-slope converters sit inside bench multimeters and panel meters because the long integration averages out noise and cancels mains hum when the integration time is a whole number of mains cycles. The price is a slow reading, a few per second.
3-bit DAC with opamp and switches, input 110, 6 V reference: input resistance Rin and current I
- (A) and
- (B) and
- (C) and
- (D) and
Answer: (A) Official key: A
- This is a weighted-resistor DAC: each bit switches in a resistor whose conductance is proportional to the bit weight. The MSB has the smallest resistor (), the LSB the largest ().
- The opamp holds its inverting input at virtual ground, so every closed branch has the full 6 V across it, regardless of the other branches.
- Input 110 means and are closed, is open. The reference sees and in parallel: .
- The current is . An ideal opamp draws no input current, so all of this flows through the feedback resistor.
- Option (A): and .
Trap: treating the input resistance as infinite because the opamp input is, which mixes up the opamp input with the DAC's reference input. The output is , a value only an ideal opamp with unlimited supply would reach. We solved the virtual-ground model for each option: only 2 kilohm and 3 mA match.
Weighted-resistor DACs show why practical converters use R-2R ladders instead: resistor values must span a wide range, and every extra bit doubles the largest value. The summing-node idea is the same one used in audio mixers and in current-output DAC stages.
Sample capacitor opened at t = 0.5 s feeding an ADC (10 Mohm parallel 0.1 uF): voltage Vx at 1.5 s
Answer: Official key: 1.50 to 1.54
- This is a sample-and-hold. While the switch is closed the capacitors track the signal; once it opens they hold the last value, but the ADC input resistance slowly bleeds the charge away.
- Held value at opening: .
- After opening, the hold capacitor and the ADC input capacitance are in parallel, so the total is . Both discharge through the input resistance.
- Time constant: .
- Decay for : .
Trap: using only the hold capacitor, , which gives 0.92 V and falls outside the key range of 1.50 to 1.54 V. The ADC's input capacitor is charged to the same voltage and shares the discharge. We integrated the discharge in 200 000 small time steps and it matched the closed form.
Sample-and-hold circuits freeze a changing signal long enough for an ADC to convert it. The hold capacitor must be large enough that leakage and the converter's input resistance do not change the value during conversion, a trade-off against how fast the capacitor can track the signal.
Maximum signal to quantisation noise ratio of a 16-bit analog-to-digital converter, in dB
- (A)48
- (B)68
- (C)88
- (D)98
Answer: (D) Official key: D
- An -bit converter has steps of size . Quantisation error is uniform over , so its noise power is .
- The largest sine wave that fits has amplitude , so its power is .
- The ratio is . In decibels, .
- For : , about 98 dB. Option (D).
Trap: using only gives 96.3 dB, which would point to 96 dB; the extra 1.76 dB comes from the sine wave's crest factor. We also quantised a full-scale sine to 16 bits and measured the ratio directly: 98.07 dB. Only 98 dB is within 2 dB; 48, 68 and 88 dB are what 8, 11 and 14-bit converters give.
Converter data sheets quote 6 dB per bit as a rule of thumb. It sets the ideal limit on the dynamic range of audio and instrumentation ADCs; real parts fall short because of thermal noise and distortion, which is what the effective number of bits measures.
Minimum number of comparators required in a 6-bit flash analog-to-digital converter
Answer: Official key: 63 to 63
- A flash ADC compares the input with every possible threshold at the same time. Each comparator outputs 1 if the input is above its threshold, so the outputs form a 'thermometer code' that an encoder turns into binary.
- A 6-bit converter must tell levels apart.
- comparators give different thermometer patterns (all 0, one 1, two 1s, up to all 1s). So , and .
Trap: answering 64 counts the codes, not the thresholds between them. We built flash converters with different comparator counts and counted the distinct output codes over a sweep of the input: 63 codes with 62 comparators, 64 codes with 63.
Flash converters are the fastest ADCs and are used in oscilloscope front ends and video, but the comparator count doubles with every extra bit, which makes the area and power grow quickly. That is why flash is rarely used beyond about 8 bits.
Address range of a 16 KB RAM added to an 8-bit microprocessor with 16 address lines and a 4 KB ROM
- (A)1000 H – 4FFF H
- (B)3000 H – 6FFF H
- (C)4000 H – 7FFF H
- (D)8000 H – BFFF H
Answer: (C) Official key: C
- Memory interfacing: the chip's own address pins take the low address bits, and the spare high bits are decoded into the chip select . The chip is selected only when (active low).
- Size check: 16 KB bytes, so the RAM takes to , matching the figure. The upper two lines, and , drive the chip select.
- is 0 only when and , that is .
- The address range with and running from all 0 to all 1 is to , which is 4000 H to 7FFF H. Option (C).
- The ROM, selected when , occupies 0000 H to 0FFF H, so the two never overlap.
Trap: ignoring the inverter on and picking 8000 H to BFFF H, which needs . We passed all 65 536 addresses through the chip-select logic: exactly 16 384 addresses select the RAM, from 4000 H to 7FFF H, with no overlap with the ROM.
Every microcontroller or processor board decodes the high address lines to choose between ROM, RAM and peripherals. A wrong decode makes two devices answer at once or leaves a gap, which shows up as bus faults at start-up.
16-bit instruction with a 7-bit opcode and three 3-bit register operands: which statements are correct
- (A)The processor has 16 internal registers.
- (B)The processor can support 128 unique operation codes (Opcodes).
- (C)The processor has up to 8 internal registers.
- (D)The processor can support 512 unique operation codes (Opcodes).
Answer: (B) and (C) Official key: B;C
- The fixed 16-bit instruction is split into fields: bits of opcode plus bits of operands is bits, so the fields fill it exactly.
- An -bit field can select things. The opcode has 7 bits, so the processor can support at most operation codes. Statement (B) is true, (D) is false.
- Each register is named by 3 bits, so at most registers can be addressed. 'Up to 8' is true, so (C) is true; 16 would need 4 bits, so (A) is false.
Trap: counting 512 as , the number of operand bits, instead of the opcode bits. We computed the field widths and tested each statement: only (B) and (C) hold.
Instruction set designers trade opcode space against register count inside a fixed word width, and the same arithmetic sizes the instruction and register fields on small microcontrollers and soft cores used in instruments. More registers or opcodes need wider instructions or variable-length encoding.