GATE Instrumentation (IN): Electrical Circuits and Machines (network theorems, transients, AC power, coupled inductors, transformers, induction motors), previous-year questions solved, part 3
Part 3 of 4 of the Electrical Circuits and Machines hub: 7 more official GATE IN questions on resonance, coupled inductors and passive filters, each solved step by step and checked against the official answer key. The other parts cover DC networks, network theorems and two-ports, transients in RC, RL and RLC circuits, AC circuits: phasors, power and RMS values and transformers and electrical machines.
Questions from official GATE IN papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 19 Nov 2026 · 7 of 30 questions on this page
Band-pass filter with R0 = 50 ohm, L0 = 1 mH, C0 = 10 nF in series, output across R0: Q factor
Answer: Official key: 6.22 to 6.42
- The inductor, capacitor and resistor are in series, with the output taken across the resistor. That is a series resonant circuit: the output peaks at the resonant frequency , where the inductive and capacitive reactances cancel. The quality factor measures how narrow the peak is: .
- (about ).
- , so .
- Cross-check with the bandwidth: with , giving . Same value.
Trap: the series formula is . Using the parallel-circuit formula gives , which would be a very wide, poor filter. We swept the frequency of , found the two half-power points and divided the centre frequency by the width: .
Series resonant band-pass stages pick out one frequency from a mix, for example a tone in an eddy-current or ultrasonic sensor and tuned receivers in telemetry. A higher Q means a narrower pass band and better rejection of nearby noise, at the cost of a slower response.
R1-L branch in parallel with R2-C branch at 100 pi rad/s: capacitance C for which Y_in is purely real
Answer: Official key: 1.40 to 1.50
- Admittances of parallel branches add. Each branch is a series impedance, so its admittance is the reciprocal of that impedance: , where .
- Reactances: . Rationalise each term: .
- Purely real means the imaginary parts cancel: .
- With this has two solutions: (each branch has the same phase angle with opposite sign) and . Here and , almost the same value because is almost equal to .
- and . Both round to .
Trap: the shortcut (the and reactances cancel) gives the same here only because . With unequal resistors the shortcut fails and the full imaginary-part condition above must be solved. We confirmed the two roots numerically: evaluated at both values of is zero to machine precision, and it changes sign across them on a scan of .
Making an input admittance real is how a reactive sensor or antenna branch is tuned so the source sees a purely resistive load. The same condition is used when a capacitor is added across a coil to bring a bridge or an AC measuring circuit to unity power factor.
4 H and 5 H coupled inductors with k = 0.6 carrying 1 mA and 2 mA sine currents: peak stored energy
mA
as shown in the figure. The coupling coefficient between the inductors is 0.6. The peak energy stored in the circuit is _______J (rounded off to two decimal places).
Answer: Official key: 17.00 to 18.00
- The energy stored in two coupled inductors is the sum of the two self-energies and the mutual energy: . The sign is plus when both currents enter the dotted terminals, as in the figure, because the two fluxes then add.
- Mutual inductance from the coupling coefficient: .
- The two currents are in phase and proportional (), so every term peaks at the same instant, when : , .
- .
Trap: subtracting the mutual term, which gives . That is the answer when one current enters a dotted and the other a non-dotted terminal. The energy must also never be negative for , which the plus sign respects. We evaluated on a dense grid over ten cycles and its maximum was .
Stored energy in coupled coils matters for transformers, linear variable differential transformers and wireless-power or inductive sensing coils. The dot convention tells the designer whether the mutual flux helps or opposes, which fixes both the energy and the sign of the induced voltage.
Source 10 sqrt(2) sin(20000 pi t) V with 50 ohm internal resistance: RMS current in a series R, L, C loop
Answer: Official key: 99.0 to 101.0
- The source, its internal resistance, the resistor, the inductor, the capacitor and all sit in one series loop, so the same current flows through every element, including . Add the impedances in series.
- At : and .
- The inductive and capacitive reactances are equal, so they cancel: the loop is at series resonance and its impedance is the sum of the resistances alone, .
- The RMS source voltage is , so .
Trap: leaving the internal resistance out, which gives , or using the peak voltage , which gives peak rather than the RMS value asked. Complex arithmetic gives and .
A series resonant loop passes the most current at one frequency, set by L and C, and is limited only by the resistance. Resonant sensors, tuned pickups and LC oscillator circuits are set up this way, and the source's own output resistance has to be included in the loop resistance.
Two equal coupled coils: 500 mH series-aiding, 300 mH series-opposing, find the coupling coefficient
Answer: Official key: 0.25 to 0.25
- When the coil currents add their flux (series-aiding) the total inductance is . When they oppose (series-opposing) it is , where is the mutual inductance.
- Subtract: , so .
- Add: , so . The coils are equal, so .
- The coupling coefficient is .
Trap: using by dividing the difference by 2 instead of 4, which would give . The factor of 4 appears because enters the series formula with the factor in each of the two connections. As a check, and , and stays between and as it must.
Measuring the inductance of a pair of windings in series-aiding and series-opposing connection is a standard bench test for finding mutual inductance and coupling in transformers, LVDTs and coupled coils. The coupling coefficient shows how much of the flux of one coil actually links the other.
Coupled inductors 3 H and 2 H with mutual inductance 4 H and given dots: equivalent T-model L1, L2, L3
- (A)
- (B)
- (C)
- (D)
Answer: (A) Official key: A
- Sign of the mutual inductance from the dot convention: when both currents enter the dotted ends of their coils, the mutual flux adds and ; when one current enters a dotted end and the other an undotted end, it subtracts and . Here enters , the dotted top of the 3 H coil, but enters , the top of the 2 H coil, whose dot is at the bottom. So .
- The coupled coils obey and .
- The T-network of Figure (b), with the common bottom wire, gives and . Matching the two sets of equations term by term: .
- and .
- The T-model is . Option (A).
Trap: reading as gives , , , which is the same T-network with the dots the other way round (not one of the options). A negative inductance in the T-model is acceptable, since it is only an equivalent for the coupled pair. We built the inductance matrix and compared it with for each option: only (A) matched.
The T-equivalent removes the magnetic coupling so that ordinary circuit analysis can be used, and it is the standard way to model a transformer or a pair of coupled sensor coils such as an LVDT. Dot positions matter in practice because reversing one winding turns an adding coupling into a subtracting one.
RLC filter with R in series and an L-C series branch across the output: what type of filter is it
- (A)low pass filter
- (B)high pass filter
- (C)band pass filter
- (D)band stop filter
Answer: (D) Official key: D
- Read the circuit as a voltage divider: the resistor is in series with the signal and the output is taken across the series - branch, so with .
- At very low frequency the capacitor is an open circuit, , so : low frequencies pass.
- At very high frequency the inductor is an open circuit, again, so : high frequencies pass.
- At the series resonance the two reactances cancel, , the branch is a short circuit and : one band of frequencies is rejected.
- Passing both ends and rejecting a band in the middle is a band stop (notch) filter. Option (D).
Trap: a band pass filter (option C) uses the series - branch in the signal path, so resonance passes the signal. Here the same branch sits across the output, so resonance shorts the output instead. We evaluated the transfer function for , , : the gain is 1.000 well below resonance, 1.000 well above it, and 0.0e+00 at , so the classification is band stop.
A notch filter built from a series inductor and capacitor across the signal line is the standard way to remove one interfering frequency, such as 50 Hz mains pickup on a low-level sensor signal or a fixed vibration tone on an accelerometer output. The rest of the measurement band is left almost untouched.