GATE Civil: Soil Mechanics (phase relations, classification, permeability and seepage, effective stress, compaction, consolidation, shear strength), previous-year questions solved, part 3
Part 3 of 3 of the Soil Mechanics hub: 13 more official GATE CE questions on shear strength and stress paths, each solved step by step and checked against the official answer key. Part 1 covers phase relations, index properties and classification, compaction, permeability, seepage and effective stress and consolidation.
Questions from the ten official GATE CE papers, sessions CE1 and CE2 of GATE 2022 (IIT Kharagpur), 2023 (IIT Kanpur), 2024 (IISc Bengaluru), 2025 (IIT Roorkee) and 2026 (IIT Guwahati); solutions by Skill-Lync. · Updated 17 Nov 2026 · 13 of 45 questions on this page
Angle between the major principal stress plane and the horizontal for a soil element with shear stress
Stresses acting on an infinitesimal soil element are shown in the figure (with ). The major and minor principal stresses are and , respectively. Considering the compressive stresses as positive, which one of the following expressions correctly represents the angle between the major principal stress plane and the horizontal plane?
- (A)
- (B)
- (C)
- (D)
Answer: (A) Official key: A
- Let the major principal plane make angle with the horizontal plane, so its normal makes with the axis: in .
- On a principal plane the traction is parallel to the normal: .
- The first row gives , so .
- Check with , , kPa: kPa and , the same as from the Mohr circle.
- Answer: (A)
Trap: (B) uses ; it gives the minor principal plane (69.70 degrees from the horizontal, i.e. 90 degrees away). (C) and (D) add stresses and have no basis in equilibrium.
The same principal-stress rotation is used to read triaxial and direct simple shear results and to interpret PLAXIS or FLAC output for embankments and excavations, where the rotation of principal planes tells you the likely failure surface.
Undrained shear strength of saturated clay in a UU test: cell pressure 100 kPa, deviator stress 150 kPa
In a triaxial unconsolidated undrained (UU) test on a saturated clay sample, the cell pressure was 100 kPa. If the deviatoric stress at failure was 150 kPa, then the undrained shear strength of the soil is _________ kPa. (in integer)
Answer: Official key: 75 to 75
- At failure: kPa and kPa.
- For a saturated clay in a UU test, raising the cell pressure only raises the pore pressure by the same amount (). The effective stresses at failure, and hence the strength, are the same at any cell pressure, so the total-stress envelope is horizontal: .
- A horizontal envelope touches the Mohr circle at its top, so the strength equals the circle radius: .
- Answer:
Trap: 150 kPa is the deviator stress (the circle's diameter), and 125 kPa is the centre of the circle; neither is the shear strength.
UU triaxial tests to IS 2720 (Part 11) on Shelby-tube samples give the used for the short-term (end-of-construction) stability of embankments on soft clay and for the skin friction of bored piles in clay.
Match loose sand volume change and pore pressure in triaxial shear, B for saturated soil and Nq for clay
Match the following in Column X with Column Y:
| Column X | Column Y |
|---|---|
| (P) In a triaxial compression test, with increase of axial strain in loose sand under drained shear condition, the volumetric strain | (I) decreases. |
| (Q) In a triaxial compression test, with increase of axial strain in loose sand under undrained shear condition, the excess pore water pressure | (II) increases. |
| (R) In a triaxial compression test, the pore pressure parameter “B” for a saturated soil | (III) remains same. |
| (S) For shallow strip footing in pure saturated clay, Terzaghi’s bearing capacity factor () due to surcharge | (IV) is always 0.0. |
| (V) is always 1.0. | |
| (VI) is always 0.5. |
Which one of the following combinations is correct?
- (A)(P)-(I), (Q)-(II), (R)-(V), (S)-(V)
- (B)(P)-(II), (Q)-(I), (R)-(IV), (S)-(V)
- (C)(P)-(I), (Q)-(III), (R)-(VI), (S)-(IV)
- (D)(P)-(I), (Q)-(II), (R)-(V), (S)-(VI)
Answer: (A) (P)-(I), (Q)-(II), (R)-(V), (S)-(V) Official key: A
- (P) Loose sand contracts as it is sheared: grains roll into the voids, so the volume keeps falling (, taken positive for expansion, decreases). (I).
- (Q) Undrained, the same contraction tendency cannot happen, so the load is passed to the pore water and the excess pore pressure keeps rising. In very loose sand this is what leads to static liquefaction. (II).
- (R) . Water is far stiffer than the skeleton: with , , , i.e. 1.0 for a saturated soil. (V).
- (S) Pure saturated clay is analysed with . Terzaghi's with gives and . (V).
- Answer: (A)
Trap: (D) sets , confusing it with . At the surcharge term is simply , so .
Geotechnical labs back-pressure saturate triaxial samples and check that is about 0.95 or more before shearing, and pore-pressure build-up in loose saturated sand is the basis of the liquefaction checks done for sites in seismic zones IV and V under IS 1893.
Matching triaxial compression, triaxial extension and direct shear tests to three points on a slip surface
A possible slope failure is shown in the figure. Three soil samples are taken from different locations (I, II and III) of the potential failure plane. Which is the most appropriate shear strength test for each of the sample to identify the failure mechanism? Identify the correct combination from the following options:
P: Triaxial compression test
Q: Triaxial extension test
R: Direct shear or shear box test
S: Vane shear test
- (A)I-Q, II-R, III-P
- (B)I-R, II-P, III-Q
- (C)I-S, II-Q, III-R
- (D)I-P, II-R, III-Q
Answer: (A) I-Q, II-R, III-P Official key: A
- A laboratory test is chosen so that its stress path matches the field stress path at that point of the slip surface.
- III, below the crest: the slip surface is steep and the weight of the soil above drives the failure. The vertical stress is the major principal stress and grows relative to the horizontal one (, active-type loading). That is a triaxial compression test (P).
- II, at the bottom: the slip surface is nearly horizontal and the soil is sheared along that plane, exactly what a direct shear (shear box) test imposes (R).
- I, at the toe: the sliding mass pushes the soil up and out, so the horizontal stress becomes the major principal stress (, passive-type loading). That is a triaxial extension test (Q).
- Answer: (A) I-Q, II-R, III-P
Trap: (D) swaps the crest and toe. Compression at the toe looks natural because the toe is loaded, but there the vertical stress is not the major principal stress. The vane shear test (S) gives only the undrained strength of soft clay and does not model the stress path at all.
For cut slopes, embankments and tailings dams, consultants order triaxial compression and extension tests and direct shear tests on samples from different parts of the likely slip surface, because the strength of an anisotropic clay differs between these loading modes and using compression strength everywhere can overestimate the factor of safety.
Angle of internal friction of sand failing at 35 kPa shear stress under 50 kPa normal stress in direct shear
A drained direct shear test was carried out on a sandy soil. Under a normal stress of 50 kPa, the test specimen failed at a shear stress of 35 kPa. The angle of internal friction of the sample is ________ degree (round off to the nearest integer).
Answer: Official key: 35 to 35
- In a direct shear box the failure plane is forced to be the horizontal plane, so the measured normal and shear stresses act on the failure plane itself.
- Sand in a drained test has , so Mohr-Coulomb gives .
- , so .
Trap: using gives . The sine form, , belongs to a Mohr circle from a triaxial test, not to stresses measured on the failure plane in a shear box.
Direct shear tests to IS 2720 Part 13 on sand fill and granular backfill give the used for retaining-wall pressures and bearing capacity checks; testing three or more normal stresses on the same sand confirms that is effectively zero.
Undrained cohesion of a cohesive soil that fails at 76 kPa axial stress in an unconfined compression test
An unconfined compression strength test was conducted on a cohesive soil. The test specimen failed at an axial stress of 76 kPa. The undrained cohesion (in kPa, in integer) of the soil is ________ .
Answer: Official key: 38 to 38
- In an unconfined compression test the cell pressure is zero: and .
- For a saturated cohesive soil tested undrained, , so the Mohr-Coulomb envelope is horizontal and the shear strength equals the radius of the Mohr circle.
Trap: reporting the failure stress itself, , as the cohesion. That is the diameter of the Mohr circle, twice the shear strength.
The UCS test (IS 2720 Part 10) is the quickest strength test in a soil investigation report; its for soft to stiff clays goes straight into short-term bearing capacity, pile shaft adhesion and excavation stability checks.
Loading that gives a stress path OP rising at 1 in 1 on a p-q plot from a non-hydrostatic initial state
In the given figure, Point O indicates the stress point of a soil element at initial non-hydrostatic stress condition. For the stress path (OP), which of the following loading conditions is correct?
- (A) is increasing and is constant
- (B) is constant and is increasing
- (C) is increasing and is decreasing
- (D) is decreasing and is increasing
Answer: (A) increasing, constant Official key: A
- With and : and .
- OP rises 1 for 1 towards larger : . Subtracting, ; adding, .
- Check the others: (B) gives (slope ); (C) gives , steeper than 1:1 (vertical if the changes are equal); (D) makes fall.
- Answer: (A) is increasing and is constant
Trap: (C). Both changes raise , so it looks like a stronger version of the same path, but they cancel in and the path tilts steeper than 45°. Only a standard triaxial compression test (constant cell pressure) gives exactly 1:1.
Stress-path triaxial testing is used for metro tunnels, deep basements and embankments on soft clay, where loading (embankment) and unloading (excavation) follow different paths; the 45° path of conventional triaxial compression matches only the vertical loading case.
Deviator stress in a correct CD test on sand after a faulty undrained run gave 360 kPa at 70 kPa pore pressure
A consolidated drained (CD) triaxial test was carried out on a sand sample with the known effective shear strength parameters, and . In the test, prior to the failure, when the sample was undergoing axial compression under constant cell pressure, the drainage valve was accidentally closed. At the failure, 360 kPa deviatoric stress was recorded along with 70 kPa pore water pressure. If the test is repeated without such error, and no back pressure is applied in either of the tests, what is the deviatoric stress (in kPa, in integer) at the failure? ________
Answer: Official key: 500 to 500
- With , failure in effective stresses: , so the deviator at failure is .
- Faulty test: gives . With and no back pressure, the cell pressure was .
- Correct CD test at the same cell pressure: , so .
- Deviator stress at failure
Trap: adding the pore pressure once, . The 70 kPa lowers , and the deviator scales with by a factor , so it adds , not 70.
Commercial triaxial labs run CD and CU tests to IS 2720 Part 11/12 for foundation and slope design; a pore-pressure reading during a test meant to be drained is a standard check that flags exactly this kind of valve or drainage-line fault before the results are reported.
Skempton's B from a 10 kPa cell pressure increase that produced 1 kPa pore pressure in a CU test
A soil sample was consolidated at a cell pressure of 20 kPa and a back pressure of 10 kPa for 24 hours during a consolidated undrained (CU) triaxial test. The cell pressure was increased to 30 kPa on the next day and it resulted in the development of pore water pressure of 1 kPa. The soil sample failed when the axial stress was gradually increased to 50 kPa. The pore water pressure at failure was recorded as 21 kPa. The value of Skempton's pore pressure parameter B for the soil sample is ________ (rounded off to 2 decimal places).
Answer: Official key: 0.09 to 0.11 OR 0.55 to 0.65
- Skempton: . Under an all-round (isotropic) stress change , so .
- The B-step here is the undrained increase in cell pressure from 20 to 30 kPa: .
- The pore pressure it produced: .
- .
- The failure data (axial stress and the 21 kPa pore pressure) belong to the shearing stage and are used for , not for .
Answer: . A value this far below 1 says the sample was not saturated.
Trap: dividing by the new cell pressure, . is a ratio of increments, so only the change goes in the denominator.
Commercial triaxial labs following IS 2720 Part 12 apply back pressure and run exactly this B-check before shearing; a CU test is normally not started until B reaches about 0.95, because an unsaturated sample gives misleading pore pressures and effective strength parameters.
Which saturated fine-grained soil can have a negative Skempton pore pressure coefficient A?
Which one of the following saturated fine-grained soils can attain a negative Skempton's pore pressure coefficient (A)?
- (A)Quick clays
- (B)Normally-consolidated clays
- (C)Lightly-consolidated clays
- (D)Over-consolidated clays
Answer: (D) Over-consolidated clays Official key: D
- In undrained shear with for saturated soil. carries the sign of the pore pressure generated by shearing.
- A soil that tends to contract when sheared drained develops positive when sheared undrained (). A soil that tends to dilate develops negative ().
- Typical : quick (highly sensitive) clays 1 to 3, as the structure collapses; normally consolidated clays 0.5 to 1; lightly over-consolidated clays 0 to 0.5.
- Heavily over-consolidated clays are dense relative to their current stress and dilate, so is about to 0.
Answer: (D) Over-consolidated clays.
Trap: (C). Lightly over-consolidated clay still contracts on shearing, so its stays positive; only heavily over-consolidated clay goes negative.
Negative pore pressure in stiff over-consolidated clay makes its short-term undrained strength higher than its long-term drained strength, which is why cut slopes and basement excavations in such clay are checked with effective-stress parameters from CU tests with pore pressure measurement.
Sand failing when axial stress drops to 100 kPa at 300 kPa cell pressure: failure plane angle
A drained triaxial test was conducted on a saturated sand specimen using a stress-path triaxial testing system. The specimen failed when the axial stress reached a value of from an initial confining pressure of .
The angle of shearing plane (in degrees) with respect to horizontal is ________ (rounded off to the nearest integer).
Answer: Official key: 30 to 30
- The specimen starts isotropic at 300 kPa and the axial stress is reduced to 100 kPa at constant cell pressure (axial unloading). So at failure acts horizontally and acts vertically.
- Drained test on sand, : , so .
- The failure plane makes with the major principal plane.
- is horizontal, so the major principal plane is vertical. A plane at to the vertical is at to the horizontal.
Answer: with the horizontal.
Trap: writing . That is the angle to the major principal plane, which is horizontal only in ordinary compression tests. In this extension-type stress path the major principal stress is the horizontal cell pressure.
Stress-path triaxial tests with axial unloading are run for deep excavations and metro station boxes, where the soil in front of the wall loses vertical stress while the horizontal stress stays high, so the strength measured in ordinary compression can be unconservative.
CD triaxial test on a normally consolidated clay, Mohr circle from 50 to 100 kPa: what is the friction angle?
The results of a consolidated drained triaxial test on a normally consolidated clay are shown in the figure. The angle of internal friction is
- (A)
- (B)
- (C)
- (D)
Answer: (B) Official key: B
- In a drained test the pore pressure is zero at failure, so the circle is already in effective stresses: , .
- A normally consolidated clay has : its failure envelope passes through the origin O and touches the circle.
- Centre , radius . The tangent from O makes .
- , so : option (B).
Trap: dividing the deviator stress by alone gives , option (A), that is . The tangent is drawn from the origin to the circle, so the hypotenuse is the distance to the centre, 75 kPa, not 100 kPa.
Consolidated drained and consolidated undrained triaxial tests to IS 2720 (Part 12) give the effective friction angle used for long-term stability of cuttings, embankments and retaining walls in clay; for soft normally consolidated clays the lab report usually gives c' close to zero, exactly as here.
UCS as a UU test, CD parameters for rapid construction, vane shear, phi in UU tests: which are correct?
In the context of shear strength of soil, which of the following statements is/are CORRECT?
- (A)The unconfined compression test is a special case of the unconsolidated-undrained (UU) triaxial tests.
- (B)The shear strength parameters obtained from the consolidated-drained (CD) triaxial tests should be used to analyse rapid construction in clay.
- (C)Vane shear test is commonly used for determining in situ undrained strength of saturated clay soils.
- (D)In an unconsolidated-undrained (UU) triaxial tests, the angle of internal friction () is equal to zero.
Answer: (A), (C) and (D) Official key: A;C;D
- (A) correct. The unconfined compression test is a UU test with cell pressure ; it gives .
- (B) wrong. Rapid construction on a clay of low permeability loads it with no time for drainage, so the undrained (UU) strength governs (end-of-construction case). CD parameters , are for long-term, fully drained conditions.
- (C) correct. The field vane is pushed into soft saturated clay and rotated; the torque gives the in situ undrained strength without sampling disturbance.
- (D) correct for saturated soil, which the statement assumes: extra cell pressure goes entirely into pore pressure, every Mohr circle has the same diameter, the envelope is horizontal and .
- Correct statements: (A), (C) and (D).
Trap: rejecting (D) because a partially saturated soil shows some in a UU test. The textbook UU result (and the key) refers to saturated clay, where . Picking (B) is the bigger error: drained parameters would overestimate the short-term strength of a fast-loaded clay.
Embankments on soft clay, such as coastal highways and port reclamations, are checked for end-of-construction stability with undrained strength from field vane tests (IS 4434) and UU or unconfined tests (IS 2720 Parts 11 and 10), while long-term slopes and retaining structures use CD or CU effective parameters.