GATE Civil: Foundation Engineering (site investigation, stress distribution, earth pressure, slope stability, shallow foundations, piles), previous-year questions solved, part 2

Part 2 of 3 of the Foundation Engineering hub: 16 more official GATE CE questions on stability of slopes and shallow foundations: bearing capacity and settlement, each solved step by step and checked against the official answer key. Part 1 covers site investigation and in-situ tests, stress distribution in soil, earth pressure and retaining walls and deep foundations: piles and pile groups.

Questions from the ten official GATE CE papers, sessions CE1 and CE2 of GATE 2022 (IIT Kharagpur), 2023 (IIT Kanpur), 2024 (IISc Bengaluru), 2025 (IIT Roorkee) and 2026 (IIT Guwahati); solutions by Skill-Lync. · Updated 17 Nov 2026 · 16 of 43 questions on this page

GATE 2023 · CE1 · Q.56NAT · 2 marksStability of slopes

Critical height of a c-phi soil layer forming parallel to a 35 degree rock slope (infinite slope, no water)

A soil having the average properties, bulk unit weight = 19 kN/m3; angle of internal friction = 25° and cohesion = 15 kPa, is being formed on a rock slope existing at an inclination of 35° with the horizontal. The critical height (in m) of the soil formation up to which it would be stable without any failure is ________ (round off to one decimal place).

[Assume the soil is being formed parallel to the rock bedding plane and there is no ground water effect.]

Answer: Official key: 4.8 to 5.2

  1. A soil layer parallel to a long rock slope fails by sliding on the soil-rock interface: an infinite slope with vertical depth and slope angle .
  2. On that plane: and . At failure , so .
  3. , , ; denominator kPa/m.
  4. m. Check: at this depth .
  5. m

Trap: dropping the (writing ) gives m. The weight of a vertical slice must be resolved twice, once onto the sloping plane and once per unit plane area.

Where this shows up in industry

Residual soil and colluvium over inclined rock bedding along hill roads in the Western Ghats and the Himalaya fail as shallow translational slides; highway engineers use this infinite-slope check to judge the safe thickness of the soil cover before deciding on drainage, soil nailing or removal.

GATE 2024 · CE1 · Q.54NAT · 2 marksStability of slopes

Minimum friction angle for a 30 degree infinite cohesionless slope with seepage parallel to the surface

An infinite slope is made up of cohesionless soil with seepage parallel to and up to the sloping surface. The angle of slope is with respect to horizontal ground surface. The unit weights of the saturated soil and water are and , respectively.

The minimum angle of shearing resistance of the soil (in degrees) for the critically stable condition of the slope is ____________ (rounded off to the nearest integer).

Answer: Official key: 48 to 50

  1. Take a plane parallel to the surface at depth , with . Normal stress , shear stress .
  2. Flow parallel to the slope with the water table at the surface gives , so with .
  3. For : .
  4. Critically stable, : , so .
  5. Answer: (key 48 to 50).

Trap: using the dry-slope result . Seepage parallel to the slope halves the effective normal stress here (), so the soil needs a much larger . Inverting the ratio gives , which is unsafe too.

Where this shows up in industry

Monsoon failures of residual-soil and colluvium slopes along hill roads in the Western Ghats and the Himalaya are screened with exactly this infinite-slope expression: a slope that stands at 30 degrees when dry can fail once a perched water table rises to the surface, which is why horizontal drains and surface drainage are specified for such cuts.

GATE 2025 · CE1 · Q.55NAT · 2 marksStability of slopes

Road cut in silty clay, point A 6.5 m below the GWT, shear stress 60 kPa: long-term factor of safety at A

A cut slope is made in a silty clay soil for a new road project, as shown in the figure. The locations of ground water table (GWT) and potential failure surface are shown in the figure. After the cut is made, the excess pore water pressure is fully dissipated, and the shear stress at the point A is 60 kN/m2. The factor of safety at the point A for long-term stability is ___________________ (rounded off to 2 decimal places).

Note:

Shear strength properties of silty clay: , , and

Unit weight of soil above the GWT () = 19 kN/m3

Unit weight of soil below the GWT () = 20 kN/m3

Unit weight of water () = 9.81 kN/m3

Cut slope for a road in silty clay: the hatched wedge between the existing ground surface and the steep cut is removed, a curved potential failure surface starts at the toe of the cut, and the ground water table is a dashed curve; point A on the failure surface lies 6.5 m below the water table, which in turn is 5 m below the cut face vertically above AGWT5 m6.5 mAExisting groundsurfacePotential failuresurfaceProposed road

Answer: Official key: 0.96 to 0.98

  1. Long-term stability with excess pore pressure dissipated is a drained (effective stress) problem: use and , not .
  2. Soil above A (figure): 5 m above the GWT and 6.5 m below it. Taking the normal stress on the failure surface at A as the vertical overburden (the surface is flat near A, as the question intends): .
  3. Steady pore pressure: , so .
  4. Shear strength: .
  5. , i.e. (key 0.96 to 0.98). Below 1: in the long term the soil at A is overstressed.

Trap: using gives , the short-term (end of cut) value; it hides the loss of strength as the clay swells and drains. Using for the whole 11.5 m gives , also outside the key.

Where this shows up in industry

Cuts for widening hill roads (IRC:SP:48 Hill Road Manual) and highway cuttings in clay are checked for long-term stability with drained c' and phi' and the steady water table, because a cut that stands on its undrained strength at the end of construction can fail years later as the clay drains; the same point check of shear strength against mobilised shear stress sits inside every slip-circle program.

GATE 2025 · CE2 · Q.55NAT · 2 marksStability of slopes

Canal bank in clay, cu = 30 kPa, R = 14 m, 80 degree arc, water-filled 2.5 m tension crack: factor of safety

The bank of a canal has the profile shown in the figure. The material is a homogeneous clay with a bulk unit weight of 20 kN/m3, undrained cohesion of 30 kPa and it is fully saturated (). For the trial slip circle shown, the area ABCDEA is 150 m2 and the centroid is at P. A tension crack (DE) of 2.5 m deep was also observed. Assume unit weight of water is 9.81 kN/m3 and consider 1 m run of the bank for the analysis.

Considering the canal is empty and tension crack is completely filled with water, the factor of safety against slope failure of the bank is ______ (round off to two decimal places).

Canal bank in clay: canal bed A to B, slope B to C rising 7.5 m to the crest C D, which is 5.5 m below the slip-circle centre O. The trial circle of radius 14 m runs from A under the bank to E at the bottom of a 2.5 m deep vertical tension crack D E filled with water; the arc subtends 80 degrees at O. The sliding mass ABCDEA has its centroid P 2.5 m horizontally from the vertical through O and B80°OR = 14 m5.5 m2.5 m7.5 m2.5 mPABCDENot to scale

Answer: Official key: 1.00 to 1.10

  1. slip circle: take moments about the centre O for 1 m run.
  2. Weight of ABCDEA: , acting through P at 2.5 m from the vertical through O: . The canal is empty, so no water pushes back on the face and the full bulk weight drives.
  3. Water in the crack: , horizontal, at below D, i.e. below O: .
  4. Resistance acts only along arc AE (none across the crack): , .
  5. , so (key 1.00 to 1.10). Without the crack water it would be .

Trap: reading fully saturated as submerged and using for the weight gives . Submerged weight applies only when water stands against the slope; an empty canal is the critical case.

Where this shows up in industry

Banks of irrigation canals and embankments on soft clay are checked by this Swedish circle (phi_u = 0) for the canal-empty and sudden-drawdown cases, following the slip circle procedures of IS 7894; a water-filled tension crack is included because rain or canal seepage readily fills the cracks that open at the crest.

GATE 2026 · CE1 · Q.56NAT · 2 marksStability of slopes

Critical height of an infinite slope at 22 degrees in a c-phi soil with c' = 12 kPa and phi' = 15 degrees

An infinite slope with slope angle consists of soil with the following properties:

Unit weight
Cohesion
Angle of internal friction

The critical height of the slope (in m) is ______ (rounded off to two decimal places).

Answer: Official key: 6.40 to 6.80

  1. Infinite slope, dry, depth measured vertically: . Setting gives .
  2. , , , so .
  3. Denominator: .
  4. . Since , a finite critical depth exists (for the slope would be stable at any depth). Answer: (key range 6.40 to 6.80).

Trap: leaving out and using gives 5.61 m, outside the key. The comes from resolving the weight of a vertical slice normal to the slope.

Where this shows up in industry

The infinite-slope check is used for long, shallow residual-soil cuttings and hill-road side slopes in the Western Ghats and the Himalaya, where the slip surface runs parallel to the ground at the soil-rock contact; it tells the engineer the soil thickness beyond which the cover will slide and needs benching, nailing or drainage.

GATE 2022 · CE2 · Q.17MCQ · 1 markShallow foundations: bearing capacity and settlement

True or false: monsoon footing design, sudden drawdown, quicksand and active thrust when the water table drops

Read the following statements:

(P) While designing a shallow footing in sandy soil, monsoon season is considered for critical design in terms of bearing capacity.

(Q) For slope stability of an earthen dam, sudden drawdown is never a critical condition.

(R) In a sandy sea beach, quicksand condition can arise only if the critical hydraulic gradient exceeds the existing hydraulic gradient.

(S) The active earth thrust on a rigid retaining wall supporting homogeneous cohesionless backfill will reduce with the lowering of water table in the backfill.

Which one of the following combinations is correct?

  1. (A)(P)-True, (Q)-False, (R)-False, (S)-False
  2. (B)(P)-False, (Q)-True, (R)-True, (S)-True
  3. (C)(P)-True, (Q)-False, (R)-True, (S)-True
  4. (D)(P)-False, (Q)-True, (R)-False, (S)-False

Answer: (A) (P)-True, (Q)-False, (R)-False, (S)-False Official key: A

  1. (P) True. A high water table replaces by in the and terms. Illustration: strip footing, m, m, (IS 6403: , ), , ; with the monsoon water table at ground level drops from 900 to 509 kPa (43 % less).
  2. (Q) False. Sudden drawdown removes the water's support while the slope stays saturated. Infinite slope, , : FS falls from 1.92 (submerged) to 0.98.
  3. (R) False. Quicksand needs the existing upward gradient to exceed the critical one, (about 1.0); the statement is reversed.
  4. (S) False. The active earth thrust is times the effective vertical stress. Lowering the water table changes to , so for m and it rises from 61 to 108 kN/m. Only the total thrust including water (238 kN/m) falls.
  5. Q and R false already leave only (A). Answer: (A).

Trap: (C) takes S as true by counting the vanished water pressure as part of the earth thrust, and also reverses R.

Where this shows up in industry

Footing designers apply the IS 6403 water-table correction for the highest level expected in the monsoon, not the level seen in a dry-season borehole, and IS 7894 lists sudden drawdown as a design case for the upstream slope of earth dams.

GATE 2023 · CE1 · Q.42MCQ · 2 marksShallow foundations: bearing capacity and settlement

Ultimate bearing capacity of a 30 cm circular plate back-calculated from a footing's 1706 kPa net capacity

A square footing of size 2.5 m × 2.5 m is placed 1.0 m below the ground surface on a cohesionless homogeneous soil stratum. Considering that the groundwater table is located at the base of the footing, the unit weights of soil above and below the groundwater table are 18 kN/m3 and 20 kN/m3, respectively, and the bearing capacity factor is 58, the net ultimate bearing capacity of the soil is estimated as 1706 kPa (unit weight of water = 10 kN/m3).

Earlier, a plate load test was carried out with a circular plate of 30 cm diameter in the same foundation pit during a dry season, when the water table was located beyond the plate influence zone. Using Terzaghi’s bearing capacity formulation, what is the ultimate bearing capacity (in kPa) of the plate?

  1. (A)110.16
  2. (B)61.20
  3. (C)204.00
  4. (D)163.20

Answer: (A) 110.16 kPa Official key: A

  1. Terzaghi, square footing, : . Below the base the soil is submerged: .
  2. kPa, so and .
  3. Plate: same soil, same . It bears at the bottom of the pit (no surcharge, ), the soil is dry (), and Terzaghi's circular footing uses .
  4. kPa
  5. Answer: (A) 110.16 kPa

Trap: reusing the square-footing factor and the saturated weight, kPa, gives (D); keeping the submerged weight of the footing case gives (B) 61.20 kPa. The plate was tested dry and is circular.

Where this shows up in industry

Plate load tests to IS 1888 are run in trial pits to confirm the allowable pressure for isolated footings; because a 300 mm plate stresses only a shallow zone, its result has to be scaled to the real footing size and corrected for the water-table position, exactly as in this back-calculation.

GATE 2023 · CE2 · Q.28MSQ · 1 markShallow foundations: bearing capacity and settlement

Reason for the non-uniform elastic settlement profile below a uniformly loaded flexible footing on sand

The reason(s) of the nonuniform elastic settlement profile below a flexible footing, resting on a cohesionless soil while subjected to uniform loading, is/are:

  1. (A)Variation of friction angle along the width of the footing
  2. (B)Variation of soil stiffness along the width of the footing
  3. (C)Variation of friction angle along the depth of the footing
  4. (D)Variation of soil stiffness along the depth of the footing

Answer: (B) Variation of soil stiffness along the width of the footing Official key: B

  1. A flexible footing transmits a uniform contact pressure, so any non-uniform settlement must come from the soil's response. Elastic settlement depends on the soil's stiffness (modulus), not on its strength.
  2. (B) True. The modulus of sand increases with confining stress. Below the centre the sand is confined by the loaded soil around it; at the edges it has little lateral confinement, so it is softer and the edges settle more than the centre, the reverse of the dish shape on clay.
  3. (A) and (C) False. The friction angle is a strength parameter; it governs bearing capacity, not the elastic settlement profile.
  4. (D) False. A modulus rising with depth changes the magnitude of settlement. In the limiting Gibson soil (modulus zero at the surface, increasing linearly, Poisson's ratio 0.5) a flexible uniform load settles uniformly, so variation with depth is not what makes the profile non-uniform across the width.
  5. Answer: (B) only

Trap: also ticking (D). Stiffness does increase with depth in sand, but that alone cannot make one point of the width settle more than another.

Where this shows up in industry

Flexible foundations on sand such as the floors of oil and water storage tanks and embankment bases are checked for edge-to-centre differential settlement; designers often place a stiffer granular ring beam or compacted pad under the edge because the unconfined edge is the soft spot.

GATE 2023 · CE2 · Q.58NAT · 2 marksShallow foundations: bearing capacity and settlement

Width of a square footing for a 500 kN column on clay with cohesion 25 kPa by Meyerhof's theory, FS = 3

A square footing is to be designed to carry a column load of 500 kN which is resting on a soil stratum having the following average properties: bulk unit weight = 19 kN/m3; angle of internal friction = 0° and cohesion = 25 kPa. Considering the depth of the footing as 1 m and adopting Meyerhof’s bearing capacity theory with a factor of safety of 3, the width of the footing (in m) is ________ (round off to one decimal place)

[Assume the applicable shape and depth factor values as unity; ground water level at greater depth.]

Answer: Official key: 3.0 to 3.5

  1. Meyerhof (as in IS 6403) for : , , ; shape and depth factors 1.
  2. kPa, so kPa.
  3. Net safe capacity kPa. The footing plus backfill weighs about as much as the soil removed, so the 500 kN column load is the net load: .
  4. m. The gross convention, , gives 3.19 m; the key range accepts both.
  5. m

Trap: adding to the safe capacity ( kPa) but comparing it with the column load alone gives 2.84 m. A gross capacity must be compared with the gross load, column plus footing and backfill.

Where this shows up in industry

Isolated footings for low-rise buildings on soft to medium clay are sized this way from the undrained cohesion in the soil report using the IS 6403 factors, and then checked for consolidation settlement, which often governs on clay.

GATE 2024 · CE1 · Q.18MCQ · 1 markShallow foundations: bearing capacity and settlement

Effect of a seasonal water-table rise on the Terzaghi net ultimate bearing capacity of a footing on clay

A 2 m wide strip footing is founded at a depth of 1.5 m below the ground level in a homogeneous pure clay bed. The clay bed has unit cohesion of 40 kPa. Due to seasonal fluctuations of water table from peak summer to peak monsoon period, the net ultimate bearing capacity of the footing, as per Terzaghi’s theory, will

  1. (A)remain the same
  2. (B)decrease
  3. (C)increase
  4. (D)become zero

Answer: (A) remain the same Official key: A

  1. Terzaghi, strip footing: , with the overburden at founding level.
  2. Pure clay analysed undrained: , so Terzaghi's factors are , , .
  3. Net capacity: .
  4. The water table changes only (bulk to submerged), which appears in the and terms, and both are zero. So in summer and in the monsoon. The gross does change, by , but that part is cancelled in the net value.
  5. The IS 6403 value with () is equally independent of the water table. Answer: (A) remain the same.

Trap: (B) decrease. A rising water table roughly halves the terms for a footing on sand, but for clay those terms carry no weight in the net capacity.

Where this shows up in industry

IS 6403 asks the designer to take the highest seasonal water table; on the soft marine and alluvial clays of coastal cities such as Mumbai and Kochi, footings checked with undrained cohesion from IS 2720 (Part 11) tests keep the same net capacity, so the monsoon check shifts to settlement and buoyancy rather than bearing.

GATE 2024 · CE2 · Q.22MCQ · 1 markShallow foundations: bearing capacity and settlement

Footing and soil type for a contact pressure distribution that peaks at the edges and dips at the centre

The contact pressure distribution shown in the figure belongs to a

Column on a footing resting on the ground; upward contact pressure arrows under the footing base are longest at the two edges and shortest at the centreFooting
  1. (A)rigid footing resting on a cohesionless soil.
  2. (B)rigid footing resting on a cohesive soil.
  3. (C)flexible footing resting on a cohesionless soil.
  4. (D)flexible footing resting on a cohesive soil.

Answer: (B) rigid footing resting on a cohesive soil. Official key: B

  1. The figure shows contact pressure smallest at the centre and rising sharply towards both edges.
  2. Flexible footing (either soil): it cannot redistribute load, so the contact pressure equals the applied uniform pressure. Only the settlement profile changes (dish-shaped on clay, larger at the edges on sand). That rules out (C) and (D).
  3. Rigid footing on clay: it forces uniform settlement. An elastic, cohesive medium can only settle uniformly if pressure is concentrated at the edges; the elastic solution for a rigid strip is , which is at the centre and very large at the edges (limited in practice by local yielding).
  4. Rigid footing on sand: the edge soil has no confinement and little strength, so pressure is near zero at the edges and maximum at the centre, the opposite shape.
  5. Answer: (B) rigid footing resting on a cohesive soil.

Trap: (A). Edge peaks belong to clay; on cohesionless soil a rigid footing's pressure is highest at the centre.

Where this shows up in industry

Footing and raft design in India (IS 456 clause 34 for footings, IS 2950 for rafts) normally assumes a uniform or linearly varying soil pressure; knowing that a stiff footing on clay really carries edge peaks explains why rafts on clay are often analysed as plates on springs and why edge reinforcement is not skimped.

GATE 2025 · CE1 · Q.56NAT · 2 marksShallow foundations: bearing capacity and settlement

6 m square footing, 2 m deep and 2 m thick, 2500 kN, clay c = 50 kPa: Terzaghi factor of safety

A 6 m 6 m square footing constructed in clay is subjected to a vertical load of 2500 kN at its centre. The base of the footing is 2 m below the ground surface, as shown in the figure. The footing is made of 2 m thick concrete. The ground water table is at a great depth. Considering Terzaghi's bearing capacity theory, the factor of safety of footing against the bearing capacity failure is ____________ (rounded off to 2 decimal places).

Note:

Unit weight of concrete = 24 kN/m3

Properties of clay: , , and

For : , ,

Square footing 6 m wide whose 2 m thick concrete block is cast with its top at the ground surface and its base 2 m below it; a vertical load of 2500 kN acts at the centreGround surfaceFooting2500 kN2 m6 m

Answer: Official key: 4.62 to 4.70

  1. Terzaghi, square footing: , with and .
  2. ; net ultimate .
  3. Load at the base: column load plus the concrete, . Gross pressure ; net pressure (the soil removed for the footing is deducted).
  4. , so (key 4.62 to 4.70). Net values are used because the overburden was there before the footing and cannot cause failure (IS 6403 convention).

Trap: dividing gross by gross, , or forgetting the 1728 kN of concrete, ; both fall outside the key.

Where this shows up in industry

IS 6403:1981 works with net ultimate bearing capacity divided by a factor of safety (commonly 2.5 to 3) and compares it with the net pressure under the footing, which is how the self-weight of thick footing blocks for water tanks, chimneys and transmission towers on clay is accounted for in design.

GATE 2025 · CE2 · Q.56NAT · 2 marksShallow foundations: bearing capacity and settlement

1 m circular plate on dry sand (16.66 kN/m3) fails at 1500 kPa: Terzaghi bearing capacity factor N-gamma

A designer used plate load test to obtain the value of the bearing capacity factor . A circular plate of 1 m diameter was placed on the surface of a dry sand layer extending very deep beneath the ground. The unit weight of the sand is 16.66 kN/m3. The plate is loaded to failure at a pressure of 1500 kPa.

Considering Terzaghi's bearing capacity theory, the bearing capacity factor is ______ (round off to the nearest integer).

Answer: Official key: 300 to 300

  1. Terzaghi for a circular footing of diameter : .
  2. Dry sand: . The plate sits on the surface: . Only the self-weight term remains: .
  3. per unit .
  4. , so (key 300 to 300). Such a high is reached only at friction angles in the mid-40s, i.e. a very dense sand.

Trap: using the strip-footing coefficient gives ; the plate is circular, so Terzaghi's shape coefficient 0.3 (0.4 for a square) applies.

Where this shows up in industry

Plate load tests to IS 1888:1982 are run at founding level on sand and gravel sites to back-figure bearing capacity and settlement for footings and machine foundations; because a plate stresses only a shallow zone (roughly twice its width), engineers scale the result to the real footing size with care.

GATE 2026 · CE1 · Q.59NAT · 2 marksShallow foundations: bearing capacity and settlement

Change in Terzaghi net ultimate bearing capacity of a strip on pure clay when the water table rises to ground

A shallow strip footing of width 2 m is embedded at a depth of 1.5 m below the ground surface in a homogeneous pure clay with an angle of internal friction zero. Consider unit weight of soil as 20 kN/m3 and undrained cohesion of soil as 20 kN/m2.

Due to rise of ground water table from far below the founding depth to the ground surface in monsoon season, the magnitude of percentage change in the net ultimate bearing capacity as per Terzaghi’s theory is _________________ (rounded off to two decimal places).

Answer: Official key: 0.00 to 0.00

  1. Terzaghi, strip: . For : , , .
  2. Net ultimate capacity: , because and .
  3. Water table deep: . Water table at ground: becomes and becomes , but both multiply zero factors, so .
  4. Change . The undrained strength is a total-stress parameter and does not change with the water table. Answer: (key range 0.00 to 0.00).

Trap: working with the gross capacity, dry and submerged (), gives a change of 10.22 %. The question asks for the net capacity, in which the overburden term cancels for .

Where this shows up in industry

IS 6403 has the designer apply a water-table reduction to the overburden and width terms; on saturated clays in flood plains and coastal sites, engineers know the short-term net capacity is governed by the undrained cohesion alone, so a seasonal rise of the water table does not reduce it, while footings on sands need the full correction.

GATE 2026 · CE2 · Q.44MSQ · 2 marksShallow foundations: bearing capacity and settlement

Rigid and flexible footings on clay and sand: true statements on settlement and contact pressure

A shallow footing is subjected to a vertical load. Within the elastic limit of the underlying soil, the TRUE statement(s) is/are:

  1. (A)Vertical displacement below a rigid shallow footing is uniform in clay as well as sand.
  2. (B)Vertical contact pressure below a rigid shallow footing is uniform in clay as well as sand.
  3. (C)Vertical displacement below a flexible shallow footing is uniform in clay as well as sand.
  4. (D)Vertical contact pressure below a flexible shallow footing is uniform in clay as well as sand.

Answer: (A) and (D) Official key: A;D

  1. A rigid footing cannot bend, so under a central vertical load it settles by the same amount everywhere, on clay or sand. (A) is true.
  2. To force that uniform settlement, the contact pressure must redistribute: on clay (elastic half-space) it is highest at the edges; on sand, where the edge soil has no confinement and little stiffness, it is highest at the centre. It is not uniform in either. (B) is false.
  3. A flexible footing simply passes the applied uniform load to the soil, so the contact pressure is uniform in both soils. (D) is true.
  4. Under that uniform pressure the settlement is not uniform: dish-shaped on clay (largest at the centre) and largest at the edges on sand. (C) is false.
  5. Answer: (A) and (D) (official key: A;D).

Trap: assuming a rigid footing also has uniform contact pressure, and marking (A), (B) and (D). Uniform pressure and uniform settlement cannot both hold: rigidity fixes the settlement, flexibility fixes the pressure.

Where this shows up in industry

The non-uniform contact pressure under rigid footings is why IS 2950 raft design and pile-cap or combined-footing design on clay use subgrade-reaction or soil-structure interaction models rather than a uniform pressure when computing bending moments, and why flexible tank bases on sand are checked for differential settlement between centre and edge.

GATE 2026 · CE2 · Q.57NAT · 2 marksShallow foundations: bearing capacity and settlement

Bearing capacity factor Nq from ultimate capacities 532.80 kPa and 864 kPa of a 1 m strip at 1 m and 2 m depth

The ultimate bearing capacity of a 1 m wide strip footing is 532.80 kPa, when it is embedded at 1 m depth in dry cohesionless soil. The soil has a unit weight of 18 kN/m3. The ultimate bearing capacity is 864 kPa when the depth of embedment becomes 2 m.

Neglecting the effect of the depth factor, the bearing capacity factor Nq is ______ (rounded off to one decimal place).

Answer: Official key: 18.2 to 18.6

  1. Cohesionless, strip, no depth factors: .
  2. The width term is the same at both depths (same soil, same ), so subtracting the two equations removes it: .
  3. .
  4. Check: gives , a consistent pair for near . Answer: (key range 18.2 to 18.6).

Trap: ignoring the term and dividing one capacity by its overburden, , which is outside the key. Two capacities are given precisely so the width term can be eliminated.

Where this shows up in industry

When plate load or footing load tests are run at two embedment depths on a sand site, engineers back-calculate the IS 6403 bearing capacity factors this way, which gives a field-calibrated to use for the remaining footings instead of a value guessed from SPT correlations.

From GATE prep to a geotechnical and foundation design career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.