GATE Civil: Fluid Mechanics and Hydraulics (fluid statics, Bernoulli, pipe flow, dimensional analysis, critical flow, hydraulic jump, GVF), previous-year questions solved, part 2
Part 2 of 2 of the Fluid Mechanics and Hydraulics hub: 21 more official GATE CE questions on specific energy and critical flow, hydraulic jump and uniform and gradually varied flow, each solved step by step and checked against the official answer key. Part 1 covers fluid properties and hydrostatics, kinematics, Bernoulli and momentum, pipe flow, boundary layer and drag and dimensional analysis and flow measurement.
Questions from the ten official GATE CE papers, sessions CE1 and CE2 of GATE 2022 (IIT Kharagpur), 2023 (IIT Kanpur), 2024 (IISc Bengaluru), 2025 (IIT Roorkee) and 2026 (IIT Guwahati); solutions by Skill-Lync. · Updated 17 Nov 2026 · 21 of 44 questions on this page
Bed width at a contraction that just causes critical flow: 3 m channel, 12 cumec, 2 m deep
Depth of water flowing in a 3 m wide rectangular channel is 2 m. The channel carries a discharge of 12 m3/s. Take g = 9.8 m/s2.
The bed width (in m) at contraction, which just causes the critical flow, is _________ without changing the upstream water level. (round off to two decimal places)
Answer: m Official key: 2.05 to 2.35
- Upstream: m/s and , so the flow is subcritical. Specific energy m.
- With no loss and the upstream level unchanged, is the same at the contraction. The narrowest width that can still pass 12 with this is the one with critical flow, where .
- m.
- Discharge per metre at critical flow: .
- Width: m. Answer: m.
Trap: dropping the velocity head and taking m gives m and m, outside the key. Any width narrower than 2.15 m chokes the channel and raises the upstream level.
Bridge piers and canal flumes narrow the waterway on purpose to save cost, and designers check exactly this critical width so that the contraction does not choke the flow and cause afflux upstream.
Smooth hump raised to choking in a frictionless rectangular channel: depths over and upstream of it
Water is flowing in a horizontal, frictionless, rectangular channel. A smooth hump is built on the channel floor at a section and its height is gradually increased to reach choked condition in the channel. The depth of water at this section is and that at its upstream section is . The correct statement(s) for the choked and unchoked conditions in the channel is/are
- (A)In choked condition, decreases if the flow is supercritical and increases if the flow is subcritical.
- (B)In choked condition, is equal to the critical depth if the flow is supercritical or subcritical.
- (C)In unchoked condition, remains unaffected when the flow is supercritical or subcritical.
- (D)In choked condition, increases if the flow is supercritical and decreases if the flow is subcritical.
Answer: (A, B, C) Official key: A, B, C
- Over a hump of height with no loss, . While the flow passes with the channel's own , so does not change in either regime: (C) is true.
- At the critical height the crest depth reaches . A higher hump cannot pass the flow with less than , so stays at (B true) and the upstream energy rises to .
- More energy at the same means a deeper subcritical flow but a shallower supercritical flow: increases if subcritical and decreases if supercritical. (A) true, (D) false.
- Example, : m. Subcritical m: m; at , rises to 2.196 m. Supercritical m: m; at , falls to 0.381 m.
- Answer: (A, B, C).
Trap: picking (D) by assuming any obstruction heads the water up. That holds only on the subcritical branch of the specific energy curve.
Weirs, raised sills and broad-crested flumes are humps used deliberately: once the crest is high enough to force critical depth, the upstream level fixes the discharge, which is how canal flow meters and Parshall-type flumes work.
Maximum number of critical depths in a compound symmetrical channel with flood plains
A compound symmetrical open channel section as shown in the figure has a maximum of ________ critical depth(s).
Bm: bottom width of main channel; Bf: bottom width of flood channel; ym: depth of main channel; y: total depth of the channel; nm: Manning's roughness of the main channel; nf: Manning's roughness of the flood channel.
- (A)3
- (B)2
- (C)1
- (D)4
Answer: (A) 3 Official key: A
- Critical depths are the stationary points of the specific energy curve, .
- Below the section is the main channel alone, so can have one minimum there.
- As the water spills onto the flood plains, the top width jumps from to , so jumps up. If it rises above 1, reaches a local maximum near , and then a second minimum on the flood plains.
- Example: m, m, m, m³/s. Minima at m and 2.14 m, a maximum at 2.00 m: three critical depths. A sweep of from 5 to 400 m³/s never gives more than 3, as found in compound-channel studies (Blalock and Sturm, 1981).
- Answer: (A) 3
Trap: a prismatic simple section has exactly one critical depth for a given ; the extra two come only from the sudden widening at the flood-plain level, not from the two roughness values.
River engineers meet this in flood studies of rivers with wide flood plains: HEC-RAS can report more than one critical depth at such cross-sections and lets the modeller choose the search method.
Condition for critical flow in a channel of any shape, with the kinetic energy correction factor
The critical flow condition in a channel is given by ________.
[Note: α: kinetic energy correction factor; Q: discharge; Ac: cross-sectional area of flow at critical flow condition; Tc: top width of flow at critical flow condition; g: acceleration due to gravity]
- (A)
- (B)
- (C)
- (D)
Answer: (A) Official key: A
- Critical flow is the depth of minimum specific energy for the given discharge: .
- Differentiate with (a thin strip of width is added at the surface): .
- Set it to zero: .
- Check: for a trapezoid ( m, side slope 1.5:1, m³/s, ) a numerical search for minimum gives m, where option A balances to within 4e-08 and B, C, D miss by 8 % or more.
- Answer: (A)
Trap: option C, with , is dimensionally wrong (m⁵ on the left, m⁴ on the right); the rectangular special case follows from A with and .
This condition is what every open-channel solver iterates on to find critical depth in irregular natural sections, the boundary condition at weirs, falls and channel transitions.
Critical depth in a 2 m wide rectangular channel carrying 30 m3/s with energy correction factor 1.1
A 2 m wide rectangular channel is carrying a discharge of 30 m³/s at a bed slope of 1 in 300. Assuming the energy correction factor as 1.1 and acceleration due to gravity as 10 m/s², the critical depth of flow (in meters) is ____________ (rounded off to 2 decimal places).
Answer: Official key: 2.88 to 2.94
- Discharge per metre width: .
- With an energy correction factor , ; setting gives , so .
- , so m.
- Check: m. The bed slope plays no part; critical depth depends only on discharge and shape.
- Answer: (key 2.88 to 2.94).
Trap: leaving out gives m, outside the key; and the slope of 1 in 300 is a distractor (it would matter for the normal depth).
Critical depth fixes the control points in every open-channel model: at a free overfall, a weir crest or a sudden steepening, HEC-RAS starts its backwater computation from critical depth, and flumes such as the Parshall flume measure discharge by forcing flow through it.
Narrowest width a 4 m channel carrying 2 m3/s at 0.4 m depth can contract to without choking
A rectangular channel is 4.0 m wide and carries a discharge of 2.0 m³/s with a depth of 0.4 m. The channel transitions to a maximum width contraction at a downstream location, without influencing the upstream flow conditions. The width (in meters) at the maximum contraction is ____________ (rounded off to 2 decimal places).
Answer: Official key: 3.30 to 3.70
- Upstream: m/s, (subcritical), m.
- A frictionless, level contraction keeps constant. As the width shrinks, rises; the narrowest width that still passes the flow without changing the upstream depth is the one where is just the minimum specific energy, i.e. flow is critical at the throat.
- Critical flow: , so m and .
- m.
- Answer: (key 3.30 to 3.70; gives 3.51 m).
Trap: calling the 0.4 m depth critical at the throat gives m; the depth falls through a subcritical contraction. Any width below chokes the flow and raises the upstream depth.
Bridge openings, flumes and canal falls are checked this way: if piers or abutments narrow a channel below this critical width the flow chokes, the upstream water level rises (afflux) and embankments can overtop, so IRC and canal design codes limit the contraction.
5 m rectangular channel, 10 m3/s at 1.5 m uniform depth: raise of the bed that just makes the flow critical
A 5.0 m wide rectangular channel carries a discharge of 10 m3/s at a depth of 1.5 m under uniform flow. To produce critical flow conditions without affecting the upstream conditions, the channel bottom elevation should be raised (in m) by ________ (rounded off to 2 decimal places).
Assume that there is no loss of head at the raise, kinetic energy correction factor is 1.0, and acceleration due to gravity is 9.81 m/s2.
Answer: Official key: 0.45 to 0.51
- ; m/s, , so the approach flow is subcritical.
- Upstream specific energy: m.
- Critical depth: m and minimum specific energy m.
- Without head loss, over the raise. The highest raise that keeps the upstream flow unchanged makes : m, so m (key 0.45 to 0.51). A higher raise would choke the channel and back the water up.
Trap: forgetting the velocity head gives m, and taking the drop in depth m as the raise also misses the key; the hump is a difference of energies, not of depths.
Broad-crested weirs and flumes used to measure canal flows work on this principle: the raised crest forces critical depth, so a single water level reading upstream gives the discharge, as in the Parshall and long-throated flumes used by irrigation departments.
Very wide channel, uniform depth 1 m, slope 0.0001, Manning n 0.02: critical depth for that discharge
Consider flow in a long and very wide rectangular open channel. Width of the channel can be considered as infinity compared to the depth of flow. Uniform flow depth is 1.0 m. The bed slope of the channel is 0.0001. The Manning roughness coefficient value is 0.02. Acceleration due to gravity, g can be taken as 9.81 m/s2.
The critical depth (in m) corresponding to the flow rate resulting from the above conditions is ______ (round off to one decimal place).
- (A)0.4
- (B)0.3
- (C)0.6
- (D)0.1
Answer: (B) 0.3 Official key: B
- In a very wide channel the hydraulic radius equals the depth, .
- Manning per metre width: , so .
- Critical depth of a rectangular section: m.
- Rounded: 0.3 m, option (B). The uniform depth (1 m) is above and the uniform-flow Froude number is , so this is a mild channel.
Trap: writing without squaring gives m, which rounds to 0.4, option (A); the critical depth comes from , i.e. .
Comparing normal and critical depth is the first step in any HEC-RAS or hand backwater study: it classifies each reach as mild or steep and tells the engineer whether to start the profile computation from the downstream or the upstream end.
Width of a rectangular channel that carries 96 m3/s at a critical depth of 9.8 m
Width (in m) of a rectangular channel required to carry a discharge of 96 m3/s at a critical depth of 9.8 m is _____ (rounded off to two decimal places).
Use acceleration due to gravity = 9.8 m/s2
Answer: Official key: 0.90 to 1.10
- For a rectangular channel the critical depth depends only on the discharge per unit width: .
- So .
- Width .
- Check: at critical flow , and , which gives the same width.
- Answer: (key range 0.90 to 1.10).
Trap: taking 9.8 m as the specific energy and gives , outside the key. Forgetting the square root, , gives .
Critical depth is the control used to rate flumes and to set the crest of a broad-crested weir or a canal fall: a Parshall or throated flume is narrowed until the flow passes through critical depth, so one depth reading gives the discharge.
Froude number after a hydraulic jump: 6 m channel, 30 cumec, 0.5 m upstream depth, 1.6 m loss
A hydraulic jump takes place in a 6 m wide rectangular channel at a point where the upstream depth is 0.5 m (just before the jump). If the discharge in the channel is 30 m3/s and the energy loss in the jump is 1.6 m, then the Froude number computed at the end of the jump is ___________. (round off to two decimal places)
(Consider the acceleration due to gravity as 10 m/s2.)
Answer: (key 0.20 to 0.41) Official key: 0.20 to 0.41
- and .
- Energy loss in a jump in a rectangular channel: .
- , solved by m ().
- m/s and . Answer: .
- Why the key is 0.20 to 0.41: the data over-specify the jump. The momentum equation alone gives m, and a loss of 2.43 m, not 1.6 m. Writing directly ( m) gives m and . All three fall in the key.
Trap: reporting the upstream Froude number, 4.47, which is far outside the key. After a jump the flow is always subcritical, so .
Stilling basins below spillways and canal falls are sized from these jump relations; IS 4997 picks the basin type from the incoming Froude number, and the tail-water must match the sequent depth or the jump sweeps out of the basin.
Specific force at the pre-jump and post-jump sections of a jump from 0.2 m to 1.0 m in a 1 m wide channel
A hydraulic jump occurs in a 1.0 m wide horizontal, frictionless, rectangular channel, with a pre-jump depth of 0.2 m and a post-jump depth of 1.0 m. The value of g may be taken as 10 m/s2. The values of the specific force at the pre-jump and post-jump sections are same and are equal to (in m3, rounded off to two decimal places) ________.
Answer: 0.62 Official key: 0.60 to 0.64
- Specific force of a rectangular section of width : , or per unit width .
- The discharge is not given, so get it from the jump equation: .
- , so m²/s.
- Pre-jump: m³.
- Post-jump: m³, the same, as momentum conservation requires.
- Answer: 0.62 m³
Trap: specific energy is not conserved across a jump. m and m; the difference m is the head lost in the roller.
Stilling basin design works with the specific force curve: the tailwater depth must match the sequent depth from equal specific force, or the jump sweeps out of the basin and scours the river bed.
Tail-water depth needed to form a hydraulic jump on a spillway apron, q = 7.5 m2/s, depth 0.5 m
A spillway has unit discharge of 7.5 m³/s/m. The flow depth at the downstream horizontal apron is 0.5 m. The tail water depth (in meters) required to form a hydraulic jump is ____________ (rounded off to 2 decimal places).
Answer: (sequent depth ) Official key: 4.40 to 4.70
- Supercritical flow on the apron: m/s.
- , so .
- The jump forms where the tail water equals the sequent depth (momentum balance in a horizontal rectangular channel): .
- , so m.
- Answer: (key 4.40 to 4.70; with it is 4.50 m). The jump dissipates m of head.
Trap: forgetting to square gives m, and quoting the critical depth m is not the sequent depth either.
Stilling basins below dam spillways are sized from this sequent depth: IS 4997 basin types are chosen by the incoming Froude number, and the apron level is set so the river's tail-water rating curve supplies at least y2 at every design flood, or the jump is swept downstream.
Jump in a 5 m wide horizontal rectangular channel, 15 m3/s, upstream depth 0.5 m: power dissipated
A hydraulic jump is formed in a 5 m wide rectangular channel, which has a horizontal bed and is carrying a discharge of 15 m3/s. The depth of water upstream of the jump is 0.5 m. The power dissipated by the jump (in kW) is ________ (rounded off to the nearest integer).
Note:
Acceleration due to gravity = 9.81 m/s2
Density of water = 1000 kg/m3
Kinetic energy correction factor = 1.0
Answer: Official key: 69 to 75
- Discharge per metre width , so m/s and .
- Sequent depth (Belanger): .
- Head loss in the jump: . Check with specific energies: m, m, difference the same.
- Power lost: kW, so kW (key 69 to 75).
Trap: using the discharge per metre instead of gives kW, and taking the rise in depth as the head loss gives kW; both are outside the key.
Stilling basins below spillways and barrage gates are designed to force a hydraulic jump on a concrete apron so that this energy is destroyed in the basin rather than by scouring the riverbed; IS 4997 sizes the basin from the upstream Froude number.
Hydraulic jump in a horizontal rectangular channel with a sequent depth ratio of 2: upstream Froude number
For a hydraulic jump formed in a rectangular horizontal channel, the sequent depth ratio is 2. The Froude number of supercritical stream is
- (A)
- (B)
- (C)
- (D)
Answer: (A) Official key: A
- Belanger's momentum equation for a jump in a horizontal rectangular channel: .
- With : , so .
- , which is the same as with .
- . Answer: (A) (official key: A).
Trap: dropping the half in gives , option (C). Check by substitution: , and , the given ratio.
Stilling basins below spillways and canal falls are proportioned from this relation: the incoming Froude number fixes the sequent depth the tail water must supply and the basin type (USBR or IS 4997), and a weak jump with F1 below about 2.5 needs little more than a plain apron.
GVF profile formed where a rectangular channel's bed slope changes from steeper to steep
A rectangular channel with Gradually Varied Flow (GVF) has a changing bed slope. If the change is from a steeper slope to a steep slope, the resulting GVF profile is
- (A)S3
- (B)S1
- (C)S2
- (D)either S1 or S2, depending on the magnitude of the slopes
Answer: (A) S3 Official key: A
- On both slopes the normal depth is below the critical depth, so the flow is supercritical and is controlled from upstream.
- The milder (second) steep slope has the larger normal depth: .
- The flow arrives at and must rise to . Being supercritical, it does this in the downstream channel, where its depth is below both and : zone 3 of a steep slope.
- Example (wide channel, , , slopes 0.02 to 0.008): m, m, m. Between them , a rising curve towards .
- Answer: (A) S3.
Trap: S2 forms in the opposite case, steep to steeper, where the depth falls from to the smaller in the upstream reach.
Chutes and spillway channels often change slope along their length, and water surface profile programs such as HEC-RAS march supercritical S-curves downstream from the upstream control to set wall heights.
Type of flow profile when a supercritical stream enters a mild-sloped channel
When a supercritical stream enters a mild-sloped (M) channel section, the type of flow profile would become ________.
- (A)M1
- (B)M2
- (C)M3
- (D)M1 and M2
Answer: (C) M3 Official key: C
- On a mild slope the normal depth is above the critical depth: . The space above the bed splits into three zones: zone 1 above , zone 2 between and , zone 3 below .
- A supercritical stream has , so on entering the mild reach its depth lies below both and : zone 3.
- In zone 3 of a mild channel the depth rises in the flow direction (the bed slope cannot sustain the high velocity), giving the M3 curve, which ends in a hydraulic jump to the subcritical normal depth further on.
- Answer: (C) M3
Trap: M2 is the drawdown curve between and (for example upstream of a free overfall); it needs a subcritical depth to start from, which a supercritical inflow does not have.
This is the classic flow below a sluice gate or spillway onto a gentle canal: the M3 curve and the jump that ends it decide where the stilling basin and the bed protection must go.
Water surface profiles near a bed slope change from 0.0001 to 0.0009 in a very wide channel (q = 70 m³/s/m)
A very wide rectangular channel carries a discharge (Q) of 70 m3/s per meter width. Its bed slope changes from 0.0001 to 0.0009 at a point P, as shown in the figure (not to scale). The Manning's roughness coefficient of the channel is 0.01. What water surface profile(s) exist(s) near the point P?
- (A)M2 and S2
- (B)M2 only
- (C)S2 only
- (D)S2 and hydraulic jump
Answer: (A) M2 and S2 Official key: A
- Critical depth: m.
- Normal depth of a very wide channel from Manning, : .
- Upstream, : m , a mild slope.
- Downstream, : m , a steep slope.
- Going from mild to steep, the flow passes through critical depth at P. Upstream the surface draws down from 12.80 m towards (zone 2 of the mild reach: M2); downstream it keeps falling from to 6.62 m (zone 2 of the steep reach: S2).
- Answer: (A) M2 and S2
Trap: a hydraulic jump needs supercritical flow running into subcritical flow, as at a steep-to-mild break. Here the flow goes from subcritical to supercritical smoothly, so there is no jump.
A break from a gentle to a steep slope is a natural control section: designers use the critical depth there as the starting point of backwater computations in HEC-RAS for canals, chutes and spillway approaches.
Number of degrees of freedom of a natural open channel flow with a mobile bed
The number of degrees of freedom for a natural open channel flow with a mobile bed is
- (A)2
- (B)3
- (C)4
- (D)5
Answer: (C) 4 Official key: C
- A degree of freedom here is a channel variable that can adjust itself to carry the flow and sediment it is given.
- Rigid boundary (lined canal, flume): width, slope and shape are fixed, so only the flow depth can change: 1 degree of freedom.
- Mobile boundary (alluvial river): the bed and banks are made of the sediment being carried, so the flow depth, the channel width, the longitudinal bed slope and the plan form (straight, meandering or braided) can all change with the discharge and the sediment load: 4 degrees of freedom.
- This is why alluvial channel design (Lacey's regime equations, for example) needs extra relations for width and slope that a rigid canal never needs.
- Answer: (C) 4.
Trap: counting only depth, width and slope gives 3, option (B); the plan form of a natural river adjusts too, through meandering and braiding.
River engineers on alluvial rivers such as the Ganga and Brahmaputra deal with all four at once: a bridge or barrage narrows the width, the bed scours or silts to a new slope and the channel can shift its course, which is why guide bunds and river training works are designed alongside.
Change of channel slope that produces a hydraulic jump
A hydraulic jump occurs in an open channel when the slope of the channel changes from ______.
- (A)MILD slope to STEEP slope
- (B)STEEP slope to MILD slope
- (C)MILD slope to ZERO slope
- (D)STEEP slope to a STEEPER slope
Answer: (B) STEEP slope to MILD slope Official key: B
- A jump is the only way flow can change from supercritical to subcritical. So it needs supercritical flow arriving and a subcritical state downstream.
- On a steep slope the normal depth is below critical (supercritical); on a mild slope it is above critical (subcritical). Example, , : m, m at (mild) and m at (steep).
- Steep to mild: supercritical flow meets subcritical flow, so a jump forms, option (B), on the steep reach or on the mild reach depending on the sequent depth.
- Mild to steep: subcritical to supercritical, a smooth drop through critical depth at the break. Mild to zero slope: flow stays subcritical (H2 profile). Steep to steeper: supercritical stays supercritical.
Trap: (A) also has a change of regime, but in the other direction; going from subcritical to supercritical passes smoothly through critical depth with no jump, which is why the break is used as a control section.
The same regime change is engineered at the toe of every ogee spillway: the steep chute delivers supercritical flow to a nearly flat stilling basin, and the basin floor level is set so the jump forms inside it at all discharges.
Match M1, M2 and M3 gradually varied flow profiles with a positive, negative or zero water surface slope
Gradually Varied Flow (GVF) profiles in open channels given in Column 1 are to be matched with the water surface slopes in Column 2 in the table below.
| Column 1: GVF Profile | Column 2: Water Surface Slope |
|---|---|
| (P) M1 | (I) Positive |
| (Q) M2 | (II) Negative |
| (R) M3 | (III) Zero |
Which of the following options is/are NOT correct?
- (A)(P) – (I) ; (Q) – (II) ; (R) – (I)
- (B)(P) – (I) ; (Q) – (II) ; (R) – (III)
- (C)(P) – (II) ; (Q) – (I) ; (R) – (I)
- (D)(P) – (I) ; (Q) – (III) ; (R) – (II)
Answer: (B), (C) and (D) Official key: B;C;D
- On a mild slope , and the GVF equation for a wide channel is .
- M1 (): numerator and denominator both positive, so , a backwater curve rising downstream: (P) – (I).
- M2 (): numerator negative, denominator positive, so , a drawdown curve: (Q) – (II).
- M3 (): both negative, so , the depth rises downstream towards a jump: (R) – (I).
- Only (A) has this match; the question asks for the options that are NOT correct. Answer: (B), (C) and (D) (official key: B;C;D).
Trap: marking (A) because it is the true match, missing the NOT in the stem. Another slip is giving M3 a zero slope; a zero slope means uniform flow at , which no M profile reaches except as an asymptote.
HEC-RAS steady-flow runs compute exactly these profiles by the standard step method; recognising an M1 backwater upstream of a weir or bridge, or an M2 drawdown before a fall, is how engineers sanity-check a flood level model before using it for embankment heights.
Uniform flow in a wide rectangular channel, 10 m3/s at 2.0 m deep: depth when the discharge doubles
The flow depth for a discharge of 10 m3/s in a wide rectangular channel is 2.0 m. Assume that the flow is uniform.
If the discharge is doubled, the flow depth (in m) in this channel is _________ (rounded off to two decimal places).
Answer: Official key: 3.00 to 3.20
- In a wide rectangular channel the hydraulic radius equals the depth, , and the area is .
- Manning: , so with the same channel (, , fixed) , that is .
- .
- Answer: (key range 3.00 to 3.20). With Chezy () the result is , also inside the key.
Trap: assuming depth doubles with discharge gives , and gives ; both are outside the key. Depth rises more slowly than discharge because velocity rises with depth too.
Canal engineers use this scaling to estimate how far the water level in a channel will rise when releases are increased, for example to check freeboard on an irrigation canal or the stage of a drain carrying twice its design storm flow.