1. Aim:- To write a code in matlab to simulate the forword kinematics of 2R Robotic Arm. 2. Theory:- Forword Kinematics, Forword kinematics is the process of calculating the frames of robotic links, given a configuration and robot's kinematic structure as input. It is generally refers to the use of kinematics equations…

Aim:- To solve an ordinary differential equation(ODE) and use calculated information to simulate motion of pendulum. Objectives:- 1. To solve an ordinary differential equation. 2. Generate a video which simulates the motion of pendulum. Introduction:- A pendulum is weight suspended from pivot so that it can swing…

1. Aim :- To optimize the stalagmite function and find global maxima using in build command in matlab called "Genetic Algorithm". And plot graphs for different studies such as, unbounded inputs, bounded inputs and bounded inputs with modified population size. 2. Objectives :- a. To optimize the given stalagmite function.…

Title :- Parsing NASA Thermodynamic data. Aim :- Write a code to open and read file called "Thermo.dat", extract all the required data i.e. temperatures, coefficients for different gases. Calculate specific heat, Entropy and Enthalpy for each gas with corresponding values of temperature and coefficients. Plot Specific…

Title :- "Structural Analysis of Jet Engine Blade".   Aim :- To generate a code for structural analysis of Jet Engine Blade and plot results of overall analysis.   Objective :- 1. Generate a code for structural Analysis. 2. Import the Blade geometry. 3. Generate an appropriate mesh for geometry. 4. Applying proper…

Title :- Rankine Cycle Simulator. Aim :- Create a Rankine cycle Simulator from a data given in standard thermodynamic library of steam table. Objectives :- 1. To create a Rankine cycle simulator. 2. To calculate state point of Rankine Cycle. 3.To plot the T-S and H-S curve for given input in Rankine Cycle. 4. To get output…

Titile :- Modeling, Assembling and Photorealistic Rendering of an American Chopper. Aim :- Aim of this project is to model, Assemble and render an American Chopper using SolidWorks. Objectives :- 1. To create a part drawing for each component required for Chopper bike. 2. Convert them into 3D model. 3. Make an assembly…

Aim - To Design Base Bracket from a given class-A surface and perform draft analysis on both, class-A surface as well as on final part model. Image of given class-A surface. Extracted surface from given class-A surface and give a offset of desired thickness. Final surface output after trim operation. Operations Used to…

Aim- To Create the Switch Bezel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Given class-A surface. Creating Tooling Axis. Creating…

Aim - Create the Coin Holder Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Given Class-A Surface. 1. Generation of Tooling…

 AIM: To Create the Door Handle Component from the given Class-A surface. To Create the tooling axis for the given Class-A Surface meeting the requirements of the draft angle. To Attach B side Features in the component. To perform the Draft analysis on the model.  TOOLS USED: Boundary Join Multiple extract Bisecting…

AIM: To Create the Core and cavity blocks for the switch bezel component. DESCRIPTION:   1. CREATING TOOLING AXIS - The Tooling Direction is basically the direction that the mold pulls a part. The mold is built in two separate pieces, basically. You have a Cavity side and you have the Core side. The Core…

 AIM Create the Bumper Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. OBJECTIVE To design Bumper as per automotive industry Standard.…

AIM Create the Dog House for the Door Trim considering the design rules and perform Draft analysis.  THEORY CLASS A SURFACE: Class A surface is a surface made by the designer specially in automotive design which is the aesthetic part of a body and is given as an input to the plastic designer to work on it. CLASS B…

AIM Create the Door Trim Lower Plastic component through the given Class-A surface with Heat Stakes and the locators considering the design rules and perform Draft analysis.  THEORY CLASS A SURFACE: Class A surface is a surface made by the designer specially in automotive design which is the aesthetic part of a body…

 Model 1: The parts for the assembly were separately created and then assembeled in the assembly workbench and the product file was attached to this challenge. Model 1 sketches: PART - 1 PART - 2 PART - 3 PART - 4 PART - 5 Part Creation from the created sketch: PART - 1 PART -2 PART -3 PART -4 PART -5 ASSEMBLY OF…

AIM Create the A Pillar Plastic component through the given Class-A surface and master section and perform Draft analysis.  THEORY CLASS A SURFACE: Class A surface is a surface made by the designer specially in automotive design which is the aesthetic part of a body and is given as an input to the plastic designer…

Objective: To make a solid body of a side door trim of a vehicle from the given class As of 4 parts of the door trim which are Lower Substrate, Bottle Holder, Map Pocket, and Door Armrest. Also, B side features like doghouse, heat stake and locator should be added, all obeying the design rules and guidelines.  Theory:…

Aim :- To  Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors & Clip. Typical design flow of EDS System.   Defining the connector  We need to define…

Wiring harness routing & packaging Rules Week 3 Challenge Q1. Download following clip cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. P-Clamp Process: Create two points one as entry and another as exit point. create planes at two points and…

Aim:  1) To Route the following harness layout in the Electrical workbench. 2) Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Given: CAD data of the following Connectors:  DT06-4S DT06-6S DT06-2S DT06-08SA Connectors Layout Design: Steps to be followed: 1. Download…

AIM-  Route two electrical harnesses as per the given layout and interconnect them as a single harness assembly and then check for bundle continuity, bundle warnings, and then give annotations to the final harness assembly. OBJECTIVE-   The objective of this project is to first route the two Harness…

AIM:  To flatten the wire harness assembly completed in week 4 assignment and place the flattened view on a drawing sheet.  OBJECTIVE:  To flatten the wire harness assembly completed in week 4 assignment. To orient the wire bundle as shown in the layout.     To place the flattened view on a drawing…

AIM:  To flatten the wire harness assembly completed in week 4 assignment and place the flattened view on a drawing sheet.  OBJECTIVE:  To flatten the wire harness assembly completed in week 4 assignment. To orient the wire bundle as shown in the layout.   To place the flattened view on a drawing sheet.…

Aim- To route the wiring harness on given Engine and flatten view drawing in CATIA V5. Objective- The objective of the project is to route the wiring harness on given Engine and prepare flatten view drawing in CATIA V5. All types of packaging rules have to be considered while routing the harness. Also, Industry best practices…

Problem Statement :- 1. Route the Wiring harness on Given car body and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. 2. Available connector 3D data can be used,…

Automotive benchmarking :- Automotive benchmarking refers to systamatic comparison of processes, services and products in automotive industry. This basically involves intensive research and even collabration with companies to improve there products, services and processes being offered to company. The purpose of benchmarking…

UNDERBODY COATING :- Underbody coating is thick cladding (Typically made up of rubber) that is placed unifromly to the car's underside. When the automobile is fresh off the lot and spotless. It is usually sprayed or painted on underbody of vehicle. But it is acceptable if you apply the undercpoating after couple of years.…

AIM: Our aim for this project is to create a hood assembly from the hood outer panel which is provided as input surface to us according to the master section sketch. INTRODUCTION The hood is the hinged cover over the engine of motor vehicles. Hoods can open to allow access to the engine compartment (or trunk on rear-engine…

AIM :- To calculate the section modulus of the previously designed hood for analyzing its strength and also optimizing the design to see the difference in the bending strength of the hood. Higher the section modulus of a structure, the more the resistive it becomes to bending. SECTION MODULUS Section modulus is a geometric…

Aim :      To calculate the wheel arch gap at required points and check whether the car passes the European standard. Objective : Study about the different wheel arch gap standards. Draw the lines at the required angle and points for the European standard. Measure the distance at each angles and mention…

AIM : From the given CLASS A SURFACE of the FENDER we have to made changes in the design and develop the model with some extra features that are : Mounting Area Bumper Drip A Pillar Sill Baffel Introduction: Fender: Fender is a part of the vehicle that frames the wheel . The primary purpose of the fender is to prevent…

OBJECTIVE: 1.Main objective of the project is to create the Roof Sheetmetal design in NX cad, and also designing Front roof rail, rear roof rail, bow roof front, bow roof rear, center roof rail and Reinforcement are creating to build the strong roof. 2.Do curvature study on Roof and performance calculations for…

Aim :         To develop the car Backdoor(Tail gate) with the reference of given skin data as per engineering standared by using NX12 Back Door :          The Back door is typically hinged, but sometimes attached by other mechanisms such as tracks, in front of an opening…