Answers  are  submitted in word file attached below  

Aim: Implement control logic of a “washing machine” using Stateflow as per given sequence:  If the power supply is available, the system gets activated  If the Water supply is not available, stop the process & indicate through LED Soaking time should be 200s followed by Washing time of 100s. Then…

I’m student of live batch-16 What is the difference between mapped and dynamic model of engine, motor and generator? How can you change model type? Solution: Mapped model- The map model is one type where the data points are pre assigned into look up tables Mapped module are useful for understanding the behaviour…

I AM A STUDENT OF LIVE BATCH-16      1.  Which types of power converter circuits are employed in electric and hybrid electric vehicle?   SOLUTION: The function of converter More properly called a voltage converter, this electrical device actually changes the voltage (either AC or DC) of an…

I AM A STUDENT OF LIVE BATCH-16   1.   For EV_defaults_in file, if cargo mass is 500 kg with all other default conditions, can the vehicle travel for 45 km with FTP drive cycle? Conclude your observations. SOLUTION: select EV_defaults_in  load file and change the cargo mass to 500kg  by keeping…

 I AM STUDENT OF LIVE BATCH-16   1. A. Explain a MATLAB demo model named ‘Speed control of a DC motor using BJT H-bridge’.         C. Refer to the help section of ‘The Four-Quadrant Chopper DC Drive (DC7) block’. Compare it with the H-bridge model.   SOLUTION:…

  I AM A STUDENT OF LIVE BATCH-16   For a defined driving cycle, calculate the energy required for braking. SOLUTION: .m file _https://drive.google.com/file/d/1Wp_ueDNY9DPdVMCrYFa85SEOAFGoHZf1/view?usp=sharing clear all clc close all m=1000; %xlsread (drivecycle.xlsx); t=drivecycle(:,1); v=drivecycle(:,3); for…

I AN A STUDENT OF LIVE BATCH -16   Part A: 1. Search and list out the total weight of various types of aircrafts.   SOLUTION: the total weight of various types of aircrafts are Type Maximum take-off weight [kg] Maximum landing weight [tonnes] Take-off run [m] Landing run [m]     Antonov An-225…

  I AM STUDENT OF LIVE BATCH-16   Create a MATLAB model of electric car which uses a battery and a DC motor. Choose suitable blocks from Powertrain block set. Prepare a report about your model including following: Objectives:         1. System level configurations      …

  I AM A STUDENT OF LIVE BATCH-16   1.Prepare a table which includes materials & chemical reactions occurring at the anode and cathode of LCO, LMO, NCA, NMC, LFP and LTO type of lithium ion cells.Give your detailed explanation on it   SOLUTION: Type of Lithium-ion Battery Cathode Material Anode Material…

  I AM A STUDENT OF LIVE BATCH-16   AIM: Battery pack capacity: 18 kWh Cell: ANR26650M1-B  Prepare a detailed battery pack drawing along with its enclosure. State your assumptions.   SOLUTION: Nanophosphate® High Power Lithium Ion Cell ANR26650M1-B Lithium Werks’ 26650 cells are capable…

  I AM A STUDENT  OF LIVE BATCH-16   AIM: For a 10 cell series lithium ion battery model, simulate the thermal effects and compare life cycle performance at various temperatures, charge & discharge rates using MATLAB. SOLUTION: PARAMETER: CYCLIC CHARGE/DISCHARGE PROFILE:   PARAMETERS:   CELL 5 FAULT: AMBIENT PARAMETER:…

  I AM A STUDENT OF LIVE  BATCH-16   AIM: Carry out a system-level simulation of an An all-terrain vehicle (ATV) is defined as a motorized off-highway vehicle designed to travel on four low-pressure or non-pneumatic tires, having a seat designed to be straddled by the operator and handlebars for steering…

I AM A STUDENT OF LIVE BATCH-16   Mini Project - Vehicle Direction Determination Aim/Objective of Mini Project: Development of MATLAB Simulink model for Vehicle Direction Detection as per requirement specified. Tag the requirements to the simulink model; tagging requirement 1 & requirement 2 to their corresponding…

I AM A STUDENT OF LIVE BATCH-16   Adaptive Cruise Control:   Objective of Main Project: Developing Adaptive Cruise Control feature as per the Requirement Document using MATLAB Simulink. Follow all the MBD related processes: Requirement Tagging & Traceability, SLDD creation, Configuration Parameter changes,…

I AM LIVE BATCH-16 STUDENT   1.Simulate the 3 test cases from harness dashboard and write a detailed report on the results SOLUTION: The Closed Loop Harness Dashboard model by Mathworks is as shown below: To select one of the 3 test conditions, it can be selected via the Test Sequence Variant block which allows you…