1. Image of the complete Draft analysis  Class A Surface Final Plastic Component Color code of the Draft Angle in various orientations (Front, Side, Top and Isometric View)  

1. Publications: 2. Draft Analysis of Class A Surface Draft Analysis of Final Plastic Component   Step:1 Intial chech of draft analysis   Step:2 Final check of draft analysis while changing the refrence tooling axis position from 3 to 5 degree.       Isometric, Front, Side, and Top View…

#22 - Week 8 - Challenge 2 - Switch Bezel Design In this challenge kindly give a short note on Tooling axis and class C surface incorrection. I need suggestions to rectify it.   Coin Holder Design Tooling Axis creation Draft Analysis on Class A Surface  Creation of Class B Surface Creation of Class C Surface…

1. Benchmark with presently available cars in the market for the following case. Renault Kiger  The price of Renault Kiger starts at Rs. 5.99 Lakh and goes upto Rs. 10.62 Lakh. Renault Kiger is offered in 20 variants - the base model of Kiger is RXE and the top variant Renault Kiger RXZ Turbo CVT DT which comes at a price…

What is under Body Coating: Underbody coating is a thick cladding (typically made of rubber) that is placed uniformly to the car’s underside. When the automobile is fresh off the lot and spotless, it is usually sprayed or painted on. But it’s acceptable if you apply the undercoating after a couple of years.…

CLASS-A SURFACE:  The class-A surface is used in the automotive design industry. it describes the final production surface data for the aesthetic parts. CLASS-B SURFACE: The class-B surface is the second surface that has a specific thickness from the class-A surface. this surface contains engineering aspects of a…

CAR HOOD DESIGN OBJECTIVE: Design hood outer panel, inner panel and reinforcements with the given outer hood skin, master section and design parameters. INTRODUCTION :  This project will make you understand about the hood of a car, explain some sheet metal operations that are commonly used in designing and take…

                                                     CORE AND CAVITY DESIGN   1. CREATING TOOLING AXIS -                       The Tooling Direction is basically the direction that the mold pulls a part. The mold is built in two separate pieces, basically. You have a Cavity side and you have the Core side. The Core pulls…

                                                      Attachment Feature Creation (Ribs & Screw Boss) in Door Handle Tooling Axis creation: It is defined as the direction in which…

                                                                           Door Handle Attachment Feature Creation CLASS A SURFACE To Create the door Trim Component from the given Class-A surface. To Create the Tooling axis for the given Class-A Surface meeting the requirements of the draft angle. To perform the Draft…

                                                                         Door Trim Lower with Engineering Features CLASS A  SURFACE…

                                                A pillar Design with Master Section CLASS A SURFACE: check the surface quality and boundary of the given class A surface.   MASTER SECTION: Master…

01 QUICK RETURN MOTION MECHANISM:  Body-01 Sloted Lever   Drawing Body-02 Base   Drawing Body-03 Rectangular Slider    Drawing Body-04 Connecting Rod    Drawing Body-05 Circular Rod   Drawing   QUICK RETURN MOTION MECHANISM: Final Assembly Drawing CV JOINT: Body-01   Drawing…

                                                                          Development of a Door Trim panel AIM To create a door interior…

        Section Modulus calculation and optimization Use the Section from your Hood design and calculate the section modulus using the formula S = I/y S = Section Modulus I = Moment of Inertia y = distance between the neutral axis and the extreme end of the object Come up with a new section that has improved the section…

Fender Design - Wheel Arch FENDER:- Fender is the US English term for the part of an automobile (vehicle body) that frames a wheel well (the fender underside). Its primary purpose is to prevent sand, mud, rocks, liquids, and other road sprays from being thrown into the air by the rotating tire. When a vehicle is moving,…

DESIGN OF CAR FENDER Fender is  the part of an automobile, motor cycle or other vehicle body that frames a wheel well (the fender underside). Its primary purpose is to prevent sand, mud, rocks, liquids, and other road spray from being thrown into the air by the rotating tire. Fenders are typically rigid and can…

 AUTOMOTIVE SHEETMETAL ROOF DESIGN USING NX CAD Objective: The main objective of this project is to develop the car roof design and its reinforcements from the given styling surface. And to prepare a detailed report about the engineering standards for roof design, its design procedure, Draft analysis and manufacturing…

Design of backdoor Backdoor/Trunk:      A Door is a hinged part which is used for entry and exit of the vehicles. Backdoor are one of the type of door of the vehicle which are located next to the passanger seat which provides access to the luggage compartment. In the most of the cars, these back door are…

 Assemble and apply GD&T to the butterfly valve assembly drawing Butterfly valve A Butterfly valve is a quarter-turn rotational motion valve, that is used to stop, regulate, and start flow.Butterfly valves are easy and fast to open. A 90° rotation of the handle provides a complete closure or opening of the…

                                                             Wiring harness design in CATIA V5  Download following connectors & Connector clip cad data from…

Q1. Download following cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. P clamp   Create entry and exit points & planes of P clamp. Defined as the electrical part design. Entry point Exit Point     Q2. Download following Back…