AIM: Create the Base Bracket Plastic component through the given Class-A surface Objectives: Create Tooling Axis. Create Class B and Class C surface. Create a solid part out of surface modelling. Draft Analysis of Class A surface and final plastic component. METHODOLOGY :  Check Class A surface for gaps using…

Firstly Check the continuity of surface Checking the connectivity of the Class A Surface if there is no gap between the components using the Join command or by using the Boundary Command. Tooling Axis The Tooling Axis is created using Bisecting Line Method. Bisecting Line Method: Base is extracted from class A surface…

AIM : Create the Coin Holder Plastic component through the given Class-A surface. INTRODUCTION : CLASS A: Class A surface which is made by a Class A designer mostly made in Autodesk Alias. Through which a plastic modelor makes the component. It is the aesthetic surface which is scene by the custromer. CLASS B:…

AIM : Create the Bumper Plastic component through the given Class-A surface. METHODOLOGY : Surafce A is made by class A designer and then it is given to the Plastic modellor to proceed further with Class B and Class C surface. SOLUTION :  First check the continuity of the component using the BOUNDRY command and use…

AIM : Create the Core and Cavity blocks for the switch bezel designed in the earlier challenge.  METHODOLOGY : TOOLING AXIS : Creation of Tooling Axis is necessary as it specifies the direction in which the Core and Cavity will be open. Also it directly affects the component and result in defects if the direction…

AIM : Create the rib for the Drill Handle considering the design rules and create the Screw boss for the Drill Handle and also perform draft analysis. OBJECTIVES : Create the Tooling axis by using the bisecting method. Design the class-B and class-C surface and join them. Create the solid feature by surfaces we create.…

AIM : Create the Door Trim Lower Plastic component through the given Class-A surface. Create the Heat Stakes and the locators considering the design rules mentioned in the video for the door applique.   OBJECTIVES :  To check continuity of Class A surface. To create a tooling direction. To perform draft…

AIM : To create A pillar plastic component using Class A surface. OBJECTIVES : To check continuity of Class A surface. To create a tooling direction. To perform draft analysis of the plastic component. To create Class B and Class C surface using Class A surface and make a closed Body.  To create Dog House considering…

AIM : TO MAKE THE PARTS FROM THE GIVEN 2D DIAGRAMS AND DO THE ASSEMBLY FOR QUICK RETURN MECHANISM. SOLUTION : QUICK RETURN MECHANISM  BODY 1 BODY 2 BODY 3 BODY 4 BODY 5 RENDERED ASSEMBLY : CV JOINT ASSEMBLY : BODY 1 BODY 2 BODY 3 RENDERED ASSEMBLY :  

AIM : Create solid part with Class A surface and create the Dog House for the Door Trim considering the design rules. OBJECTIVES : To check continuity of Class A surface. To create a tooling direction. To perform draft analysis of the plastic component. To create Class B and Class C surface using Class A surface and…

AIM : Create a door trim component through the given Class-A surface. Create the Heat Stakes, locators and Dog house considering the design rules. And do the Draft analysis. OBJECTIVES :  1.To check the boundries of Class A surface. 2. To create a tooling axis. 3. To perform draft analysis  4. To create…

BENCHMARKING : Benchmarking in an automobile industry involves a structural comparision between similar products,services (or) processes on some dimension of performance. It can be used to compare the availability and delivery of features in a product and in this form often provides the basis of consumer tests and reviews.…

UNDERBODY COATING : Undercoating is the sprayed application of a wax or rubber-based composite onto the entire underside of the vehicle. It's designed to create a rust-proof layer between the underside of the vehicle and the water, ice, and salt of the road. Undercoating provides a more comprehensive protective layer for…

AIM : Design Hood Outer Panel, Inner Panel and the necessary reinforcements by following the Master Section mentioned with the Design parameters.   Introduction :   A car hood, also referred to as a bonnet in some other countries, is the hinged cover that rests over the engine of a front-engine…

AIM : Calculate the Wheel Arch gap at required points and check whether the car passes the European standard.Objective:           Create the intersection point according to given degree angle.           Follow the European standards to prove the…

AIM: To design a  front fender of a car by following the given master section as per the design considerations of OEM. FENDER It is an aesthetic component/part of a car that frames the wheels. Prevention of sand,  mud particles, and other road contaminants from being thrown into the engine compartment and also…

AIM : For the Given Roof styling, create an ASSEMBLY by developing the essential flanges for the outer roof and creating the reinforcements. OBJECTIVE : 1.The main goal of the project is to design the roof sheetmetal in NX cad, as well as the front roof rail, rear roof rail, bow roof front, bow roof rear,…

INTRODUCTION           To generate the report on finding the section modulus for the hood design and improving it by based on the input and increasing the strength of the hood by using the software NX-CAD.   OBJECTIVES          …

Aim: To design the Back door (Tail gate) of a car from the styling surface provided using NX CAD. The ultimate aim is to design the Back Door by following the Industrial Standards. INTRODUCTION:                              A back door…

Aim: To design the Back door (Tail gate) of a car from the styling surface provided using NX CAD. The ultimate aim is to design the Back Door by following the Industrial Standards. INTRODUCTION:                              A back door is a BIW component found in all Automotive car generally used for opening and closing…

AIM: The aim of this project is to model a butterfly valve and to apply GD&T to the different parts of the butterfly valve and the assembly. INRODUCTION TO BUTTERFLY VALVE: A butterfly valve is from a family of valves called Quarter turn-valves. In operation, the valve is fully open or closed when the disc is…

  Wiring harness design in CATIA V5 - 3D modeling Week 2 Challlenge AIM:  Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors & Clip. Deutsch DT06 –…

Q1 The given clip was downloaded and opened as a part file. I have to define two points that will be used as entry and exit points. Then a plane has to be defined at the points. A base plane has to be defined at a distance of 2 to 3 mm from the clip. again we define the exit point at the first definition as the entry point.…