GATE Electrical: Electric Circuits (DC networks, dependent sources, Thevenin and Norton, RC, RL and RLC transients), previous-year questions solved

Every DC-network and switching-transient question from the last five GATE Electrical papers: counting junctions, dependent sources, Thevenin and Norton equivalents, which sources can sit in a loop, linear elements, and capacitor and inductor circuits just after a switch moves. Each solution matches the official answer key, was recomputed by a nodal solve or a time-step simulation of the switched circuit, names the trap that costs marks, and shows where the idea is used in real hardware.

Questions from official GATE EE papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 16 Nov 2026 · 16 questions

GATE 2024 · EE · Q.12MCQ · 1 markNetwork basics, sources and theorems

How many junctions does this 13-element network have?

The number of junctions in the circuit is
Network on a 3 by 3 grid: resistors along the top, a battery and an inductor on the left side, a capacitor in series with a resistor and a resistor below the centre dot in the middle column, a capacitor on the middle-left row, a wire from the centre to two inductors on the right column, a capacitor on the far right, a battery and a resistor along the bottom
  1. (A)6
  2. (B)7
  3. (C)8
  4. (D)9

Answer: (A) Official key: A

  1. A junction (principal node) is a point where three or more elements meet. Every point joined by plain wire is one and the same junction, however far apart it is drawn.
  2. Merge the wired points first: the top-right corner with the top of the right inductor, the bottom-right corner with the bottom of the lower inductor, and the centre dot with the right end of its horizontal wire.
  3. Now count the meeting points of three or more elements: top middle (two resistors and a capacitor), top right (resistor, inductor, far-right capacitor), left middle (battery, capacitor, inductor), the centre node (capacitor, two resistors, two inductors: five elements), bottom middle (battery, two resistors) and bottom right (resistor, inductor, far-right capacitor).
  4. That is 6 junctions: option (A).

Trap: counting the centre dot and the right end of the wire leaving it as two junctions, which gives 7 (option B). They are one node. Our check stores the 13 elements and 3 wires as a graph, merges the wired points and counts 9 nodes, of which 6 have three or more elements; counting drawn points without merging gives 7.

Where this shows up in industry

Node counting sizes the problem before you solve it: a circuit with nodes needs nodal equations, and SPICE builds exactly one matrix row per node after merging every wire in the netlist into a single net.

GATE 2024 · EE · Q.13MCQ · 1 markNetwork basics, sources and theorems

10 V source, α Ω, 1 Ω, 2 Ω and a 10 A source: how much power does the 10 V source deliver?

All the elements in the circuit are ideal. The power delivered by the source in watts is
10 V source (+ on top) feeding alpha ohm to a middle node; 1 ohm from the middle node to the bottom rail; 2 ohm from the middle node to a 10 A current source pointing up+−10 Vα Ω1 Ω2 Ω10 A
  1. (A)0
  2. (B)50
  3. (C)100
  4. (D)dependent on the value of

Answer: (A) Official key: A

  1. Call the middle node voltage . All 10 A of the current source flows through the into this node (a resistor in series with a current source does not change the current).
  2. KCL at the middle node: .
  3. satisfies it for every : the first term is 0 and the second is 10. So the middle node sits at exactly the source voltage.
  4. Current through : , so the power delivered by the 10 V source is : option (A).

Trap: option (D). is in the circuit, but the 10 A source and the resistor already hold the middle node at , the same as the source, so no current flows through whatever its value. Our nodal solve for and gives 0 W every time.

Where this shows up in industry

Driving a node to the same potential as its neighbour so that no current flows through the impedance between them is the 'guard' technique used in electrometers and high-impedance measurements, where a driven guard ring stops leakage current reaching the input.

GATE 2025 · EE · Q.18MCQ · 1 markNetwork basics, sources and theorems

1 A current source in parallel with 1 kΩ between X and Y: which I-V graph is right?

The I-V characteristics of the element between the nodes X and Y is best depicted by
Between terminal X (current I XY flowing in) and terminal Y: a 1 A current source pointing down (from X toward Y) in parallel with 1 kilo-ohmXIXY1 A1 kΩY
  1. (A)Option A: horizontal line at 1 AIXYVXY01 A
  2. (B)Option B: line starting at 1 A and rising with V XYIXYVXY01 A
  3. (C)Option C: line through the origin rising with V XYIXYVXY01 A
  4. (D)Option D: line starting at 1 A and falling with V XYIXYVXY01 A

Answer: (B) Official key: B

  1. enters at X and . Inside, the current source carries 1 A from X to Y whatever the voltage, and the resistor carries from X to Y.
  2. KCL at X: .
  3. A straight line with intercept 1 A at and a positive slope of 1 mS: option (B).

Trap: (A) forgets the resistor (an ideal current source alone), (C) forgets the source (a resistor alone), and (D) would need a negative resistance. Check the source direction against : the source arrow points from X to Y, the same way as , so it adds +1 A. Our solve drives from −10 V to +10 V and reads an intercept of 1.000 A and a slope of +1 mS.

Where this shows up in industry

A current source with a parallel resistance is the Norton model of a transistor's output (the current in parallel with ). The slope of the measured output I-V line on a curve tracer gives , which sets the gain of every amplifier stage built on it.

GATE 2025 · EE · Q.19MCQ · 1 markNetwork basics, sources and theorems

A nullator in series with a resistor R behaves as what?

A nullator is defined as a circuit element where the voltage across the device and the current through the device are both zero. A series combination of a nullator and a resistor of value, R, will behave as a
  1. (A)resistor of value R.
  2. (B)nullator.
  3. (C)open circuit.
  4. (D)short circuit.

Answer: (B) Official key: B

  1. Elements in series carry the same current, and their voltages add.
  2. The nullator forces , so the resistor also carries 0 A and drops .
  3. Total: and . Both are zero, which is the definition of a nullator: option (B).

Trap: option (C). An open circuit also has , but it allows any voltage across it. Here the voltage is forced to zero too. Our check lists every pair each combination allows on a grid and compares the set with each option: only the nullator's set matches.

Where this shows up in industry

The nullator is how an ideal op-amp's input is modelled in nodal analysis: its two inputs carry no current and have no voltage between them, which is the 'virtual short' rule used to analyse every op-amp amplifier and active filter.

GATE 2026 · EE · Q.23MCQ · 1 markNetwork basics, sources and theorems

A DC source with a diode, R, L and C in series: which elements are linear?

A circuit with ideal elements is shown. Which one of the following options correctly identifies all the linear elements in the circuit?
A DC source V DC (+ on top) in series with a diode D (anode toward the source), a resistor R, an inductor L and a capacitor C+−VDCDRLC
  1. (A)R only
  2. (B)R, L, and C only
  3. (C)D only
  4. (D)L, C, and D only

Answer: (B) Official key: B

  1. An element is linear when its voltage-current relation obeys superposition: scaling and adding inputs scales and adds the response.
  2. : . : . : . Multiplying by a constant and differentiating are both linear operations, so R, L and C are all linear.
  3. The ideal diode conducts only forward current at zero voltage and blocks reverse voltage at zero current. is allowed but is not, so scaling by −1 fails: the diode is nonlinear.
  4. Answer: R, L and C only, option (B).

Trap: thinking L and C are nonlinear because they store energy or involve derivatives. Linearity is about superposition, not about being memoryless. Our check feeds two random waveforms and their weighted sum into each element law: R, L and C give identical results both ways; the diode fails the sign test.

Where this shows up in industry

Linearity is what allows AC (phasor) and Laplace analysis of RLC filters. Diodes and transistors are handled by linearising them around a DC operating point (small-signal models), which is exactly what SPICE's .AC analysis does.

GATE 2026 · EE · Q.24MCQ · 1 markNetwork basics, sources and theorems

Three ideal voltage sources pin nodes X, Y and Z: what is the Thevenin equivalent between Y and Z?

For the circuit shown, which one of the following options correctly identifies the Thevenin’s equivalent parameters between nodes Y and Z?
Nodes X, Y, Z and W: 20 V source from X (-) to Y (+) above a 10 kilo-ohm X to Y; 10 kilo-ohm Y to Z (+ at Y, - at Z); 2 kilo-ohm Y to W; 100 V source from X (+) to W (-); 20 V source from W (+) to Z (-); 1 kilo-ohm Z to W−+20 V10 kΩ10 kΩ+−2 kΩ+−100 V−+20 V1 kΩXYZW
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (B) Official key: B

  1. Take W as the reference. The 100 V source runs from W to X with + at X: .
  2. The top 20 V source has − at X and + at Y: .
  3. The diagonal 20 V source has + at W and − at Z: .
  4. .
  5. For , replace every ideal voltage source by a short: Y and Z are then both tied straight to W, so . Answer: option (B).

Trap: working the 10 kΩ divider. Every node here is pinned by an ideal voltage source, so no resistor affects or , and the 10 kΩ between Y and Z is shorted out when the sources are killed. Read the turned + and − marks on the diagonal sources carefully: getting the 20 V source backwards gives 100 V (options A and C). Our nodal solve gives 140 V, and a 1 A test current between Y and Z with the sources zeroed gives 0 V.

Where this shows up in industry

A node fed by a stiff source has almost zero Thevenin resistance, which is why a regulated supply rail or a strong grid bus barely changes voltage when a load is connected. Short-circuit studies therefore use the real source impedance, not the ideal 0 Ω, to find fault currents.

GATE 2026 · EE · Q.25MCQ · 1 markNetwork basics, sources and theorems

Four loops of two sources each: which values of k1 to k4 make all of them realizable?

Refer to the four circuits shown. Which one of the following options for , , , and makes all of them realizable?
Four circuits, each a single loop of two sources: (1) independent source V D (+ top) in parallel with a dependent voltage source V X = k1 V D (+ top); (2) V D in parallel with a dependent current source I X = 0.5 k2 V D pointing up; (3) independent current source I D pointing up in parallel with a dependent voltage source V X = k3 I D (+ top); (4) I D pointing up in parallel with a dependent current source I X = 3 k4 I D pointing up+−VD+−VX = k1 VD+−VDIX = 0.5 k2 VDID+−VX = k3 IDIDIX = 3 k4 ID
  1. (A), , for all values of and
  2. (B), , for all values of and
  3. (C), , ,
  4. (D), , ,

Answer: (A) Official key: A

  1. Circuit 1: two voltage sources in parallel (both + on top). KVL round the loop needs , so : .
  2. Circuit 2: a current source across a voltage source. The voltage source fixes the voltage and absorbs any current, so it works for every .
  3. Circuit 3: a voltage source across a current source. Again any value works, so every is fine.
  4. Circuit 4: two current sources in one loop, both arrows up. Going round the loop, the left source pushes current clockwise and the right one anticlockwise, so KCL needs : , .
  5. Answer: option (A).

Trap: thinking circuits 2 and 3 restrict and . Only a loop made purely of voltage sources (KVL) or a node fed purely by current sources (KCL) constrains the values. Our check writes the nodal equations of each circuit and calls it realizable when they have a solution (rank of the matrix equals the rank of the augmented matrix): only option (A) passes for all tested , .

Where this shows up in industry

SPICE rejects the same topologies: a loop of ideal voltage sources or a node fed only by current sources gives a 'singular matrix' error. Engineers fix it by adding a small series resistance (for example the ESR of a capacitor) or a large parallel resistance.

GATE 2026 · EE · Q.44MCQ · 2 marksNetwork basics, sources and theorems

Terminal readings 18 V at −0.5 A, 30 V at 0.5 A, 36 V at 1 A: what are the Norton current and resistance?

The terminal voltage and current of a linear electrical network shown in Figure (a) are given in the table.
Terminal voltage ()Terminal current ()
18 V–0.5 A
30 V0.5 A
36 V1.0 A
The correct choice for the parameters (, ) of the Norton equivalent circuit shown in Figure (b) is:
(a) a linear electrical network with terminals X (+) and Y (-), terminal voltage v t and terminal current i t flowing into the network at X; (b) its Norton equivalent: current source I N pointing up toward X in parallel with R NElectricalNetworkitX+vt−Y(a)INRNX+Y−(b)
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (C) Official key: C

  1. flows into the network at X. In the Norton circuit both and then flow down through : , a straight line in .
  2. Slope from the first two rows: .
  3. At (open circuit): , so .
  4. Check row 3: . Answer: , , option (C).

Trap: taking the 24 V open-circuit voltage as the resistance (option D), or reading as current coming out of the network, which flips the slope sign. With the network would push 2 A out of X into a short, which is . All three table rows lie exactly on our fitted line.

Where this shows up in industry

This is how you characterise a battery, a solar module or a sensor output you cannot open: measure terminal voltage at two or three load currents, fit the line, and read off the source and internal resistance. Battery internal-resistance testers use exactly this two-load method.

GATE 2022 · EE · Q.55NAT · 2 marksNetwork basics, sources and theorems

75 V source with a 0.5 V1 dependent source and a current-controlled source I: what is V1 across 8 kΩ?

In the circuit shown below, the magnitude of the voltage in volts, across the resistor is ______________. (round off to nearest integer)
75 V battery, 2 kilo-ohm carrying current I to the right, a dependent voltage source 0.5 V1 (+ on the left), a node wired straight to the bottom rail, a dependent current source I pointing right, and 8 kilo-ohm with voltage V1 (+ at the top) back to the bottom rail75 V+2 kΩI+−0.5 V1I+−8 kΩV1

Answer: Official key: 98 to 102

  1. The vertical wire in the middle joins the node after the dependent voltage source straight to the bottom rail, so that node is at 0 V.
  2. KVL round the left loop: .
  3. The current-controlled current source pushes the same current down through the resistor: .
  4. Substitute: , so and .

Trap: thinking the middle short stops anything reaching the right half. The short only fixes a node voltage; the dependent current source still forces through the 8 kΩ. (100 V) is larger than the 75 V source because the dependent sources supply power. Our modified-nodal solve gives and .

Where this shows up in industry

Dependent sources are how transistor models are written: a BJT's collector current is a current-controlled source . An output voltage larger than the input source is exactly the gain those models predict, with the extra power coming from the supply.

GATE 2023 · EE · Q.32NAT · 1 markNetwork basics, sources and theorems

V1 = 8 V and I1 = 8 A with 0.5 Ω, two 3 Ω and two 2 Ω resistors: what is Vab?

For the circuit shown in the figure, , DC and , DC. The voltage in Volts is _________ (Round off to 1 decimal place).
I1 current source pointing up from the bottom-left node to the top-left node; 0.5 ohm from top-left to a; 3 ohm from a to b; 3 ohm from a down to a node M that is wired to b; source V1 on the diagonal from top-left (+) to M; 2 ohm from bottom-left to M; 2 ohm from bottom-left round to b. V ab is measured + at a, - at bI10.5 Ω3 Ωab+−Vab3 ΩV12 Ω2 Ω

Answer: Official key: 5.9 to 6.1

  1. Node b is wired to the node below the vertical , so both resistors run from a to b: . Both resistors run from the bottom-left node to b.
  2. Take b as reference. The source sits directly between the top-left node and b, with + at the top left, so that node is at whatever does.
  3. The and the form a divider across those 8 V: .
  4. . only sets the bottom-left node (−8 V) and the current in .

Trap: missing the wire that makes b and the lower node one node, then writing four or five node equations with in them. Spot shorted nodes and sources that pin a node first. Our nodal solve gives 6.0 V, and changing to 0, 3 or 50 A leaves unchanged.

Where this shows up in industry

Merging wired nodes is the first thing a circuit simulator does with a netlist. On a board, a regulator output fixes a rail the same way fixes this node, so a load hanging elsewhere (like ) does not change it.

GATE 2022 · EE · Q.31NAT · 1 markTransients: switching RC, RL and RLC circuits

Switch closes on 10 V with 6 Ω ∥ 3 Ω, a 1 µF + 10 Ω branch and 2 Ω: what is the steady voltage on 6 Ω?

In the circuit shown below, the switch is closed at . The magnitude of the steady state voltage, in volts, across the resistor is _________. (round off to two decimal places).
Between a left and a right rail: 6 ohm in parallel with 3 ohm; a 1 microfarad capacitor in series with 10 ohm; and a 10 V battery (+ toward the switch), an open switch S and 2 ohm in series6 Ω3 Ω1 μF10 Ω10 V+−S2 Ω

Answer: Official key: 4.95 to 5.05

  1. In DC steady state a capacitor carries no current, so the branch is an open circuit.
  2. .
  3. The 10 V source, its series and this form a divider: .
  4. The resistor is part of that parallel pair, so it sees 5.00 V.

Trap: keeping the in the steady-state calculation. It carries current only while the capacitor charges, for a few time constants of . Our time-step simulation of the switched circuit settles at 5.000 V, the same as the DC solve with the capacitor removed.

Where this shows up in industry

For a DC operating point (bias point), SPICE and hand analysis delete every capacitor and short every inductor before solving, which is why decoupling capacitors on a supply rail do not change its steady voltage.

GATE 2023 · EE · Q.29NAT · 1 markTransients: switching RC, RL and RLC circuits

10 A source, switch K opens at t = 0: what is the inductor voltage at t = 0+?

The value of parameters of the circuit shown in the figure are , , , , . For time , the circuit is at steady state with the switch ‘K’ in closed condition. If the switch is opened at , the value of the voltage across the inductor () at in Volts is ____________ (Round off to 1 decimal place).
Node X on top: switch K (closed, shown opening) in series with R3 to the bottom rail, a 10 A DC current source pointing up into X, and a block of R1 in series with L (V L, + on the left) in parallel with R2 in series with C, whose right side returns to the bottom railKR310 A,DCR1L+VL−R2C

Answer: Official key: 7.9 to 8.1

  1. For (DC steady state) the inductor is a short and the capacitor an open. The 10 A splits between and the – branch (): .
  2. So and, with no current in , .
  3. At , and cannot jump. K is open, so all 10 A enters the block: 6 A through and through –.
  4. , and .

Trap: assuming stays 0 because the inductor current is continuous. Its current is continuous; its voltage jumps. The 4 A that used to flow through is forced into the – branch and lifts node X from 12 V to 20 V. A backward-Euler simulation with a 10 ns step reads just after K opens.

Where this shows up in industry

Working out the circuit at is how engineers size snubbers and freewheeling paths: when a switch interrupts a path, the stored inductor current must go somewhere, and the circuit gives the voltage step the components will see.

GATE 2023 · EE · Q.54NAT · 2 marksTransients: switching RC, RL and RLC circuits

AC source i = sin 1000t, switch K closes and K-bar opens at t1: smallest t1 with no capacitor transient?

The circuit shown in the figure is initially in the steady state with the switch K in open condition and in closed condition. The switch K is closed and is opened simultaneously at the instant , where . The minimum value of in milliseconds, such that there is no transient in the voltage across the capacitor, is ____________ (Round off to 2 decimal places).
Top rail and bottom node B: 10 ohm, current source i(t) = sin 1000t pointing up, and switch K (open) all between them; a 100 microfarad capacitor from the top rail to node C; switch K-bar (closed) between B and C; and below, 10 ohm and a 5 V battery (+ toward the 10 ohm) in series between B and C10 Ωi(t) =sin 1000tK100 μFK10 Ω+5 V

Answer: Official key: 1.56 to 1.58

  1. Before : shorts the 10 Ω–5 V branch, so the capacitor sits directly across the and the current source. At : .
  2. , so .
  3. After : K shorts the source and the , and the capacitor is left in series with and the 5 V battery, so its final value is (same polarity).
  4. No transient means already equals 5 V: , .
  5. Smallest positive solution: , so .

Trap: ignoring the −45° phase of the capacitor voltage, which gives . The other root, , gives 3.14 ms, but the question asks for the minimum. We simulated both: switching at 1.5708 ms the capacitor voltage stays within V of 5 V; switching at 1.00 ms it is 3.49 V off and has to settle.

Where this shows up in industry

Point-on-wave (controlled) switching relays close capacitor-bank and transformer breakers at the instant the source voltage matches the trapped voltage. That avoids the inrush currents and overvoltages a random closing instant causes, and utilities fit them on most large capacitor banks.

GATE 2024 · EE · Q.14MCQ · 1 markTransients: switching RC, RL and RLC circuits

1 A source, three 1 H inductors and two 1 Ω resistors: what is the time constant after S closes?

The circuit shown in the figure with the switch open, is in steady state. After the switch is closed, the time constant of the circuit in seconds is
1 A current source pointing up; branch of 1 ohm and 1 H to the bottom rail; open switch S then 1 ohm and 1 H along the top to a node with two 1 H inductors in parallel to the bottom rail1 A1 Ω1 HS1 Ω1 H1 H1 H
  1. (A)1.25
  2. (B)0
  3. (C)1
  4. (D)1.5

Answer: (A) Official key: A

  1. The time constant comes from the circuit with the independent source turned off. A current source turned off is an open circuit.
  2. The two parallel 1 H inductors act as .
  3. With the source open, the left branch () and the right branch () form one loop: and .
  4. : option (A).

Trap: shorting the current source instead of opening it (that leaves two separate RL loops), or adding the two parallel inductors as 2 H. Our simulation starts from the open-switch state (1 A in the left inductor, 0 elsewhere) and the right-branch current rises towards 0.5 A, reaching 63.2% of the way at .

Where this shows up in industry

The time constant decides how quickly a relay or contactor coil, a solenoid valve or a motor winding builds up current after switch-on, and therefore how long a driver must hold the switch before the actuator responds.

GATE 2025 · EE · Q.57NAT · 2 marksTransients: switching RC, RL and RLC circuits

5 F capacitor, 100 V source, 2 Ω, 25 Ω and 3 A: how long after S closes does the capacitor reach 50 V?

The switch (S) closes at sec. The time, in sec, the capacitor takes to charge to 50 V is _____ (round off to one decimal place).
100 V source (+ on top) in series with a 5 farad capacitor along the top and 2 ohm along the bottom; across the right-hand top and bottom nodes: switch S (open, closes at t = 0), 25 ohm, and a 3 A current source pointing up+−100 V5 FS25 Ω3 A2 Ω

Answer: Official key: 4.0 to 4.2

  1. Before (S open, steady state) no current flows in the capacitor branch, so none flows in the either. The 3 A source drives the alone: the top-right node sits at .
  2. The capacitor's left plate is at the source's 100 V, so .
  3. When S closes it shorts the and the 3 A source. The capacitor then charges from 100 V through : and .
  4. . Setting 50 V: , , which rounds to 4.1 s.

Trap: starting from an uncharged capacitor, which gives , outside the key. The question does not say the circuit was in steady state before S closed, but the official key (4.0 to 4.2) only fits a capacitor that starts at the open-switch steady-state 25 V. Our simulation reaches 50 V at 4.05 s from 25 V and at 6.93 s from 0 V.

Where this shows up in industry

EV battery packs and inverter DC links use pre-charge circuits that charge the bus capacitor through a resistor exactly like this. The battery management system checks that the bus has reached a set fraction of pack voltage before it closes the main contactor.

GATE 2026 · EE · Q.43MCQ · 2 marksTransients: switching RC, RL and RLC circuits

10 V through 25 kΩ, 10 µF, 100 kΩ and a 1 mA step: capacitor voltage at 0+, 0.5 s and infinity?

The electrical network shown has an independent voltage source (10 V) and a current source ( mA). The voltage across the capacitor at time instants (in seconds) , , and , respectively, is:
10 V source (+ on top) through 25 kilo-ohm to a top node; from the top node to the bottom rail: a 10 microfarad capacitor, a current source pointing up that steps from 0 to 1 mA at t = 0 s, and 100 kilo-ohm+−10 V25 kΩ10 μF01 mAt = 0 s100 kΩ
  1. (A)8.00 V, 28.00 V, 26.36 V
  2. (B)8.00 V, 26.36 V, 28.00 V
  3. (C)10.00 V, 26.36 V, 28.00 V
  4. (D)10.00 V, 28.00 V, 26.36 V

Answer: (B) Official key: B

  1. Before the step the current source is 0 and the capacitor is open: . It cannot jump, so .
  2. Final value (capacitor open): source transformation, , plus 1 mA, into : .
  3. .
  4. . Answer: 8.00 V, 26.36 V, 28.00 V, option (B).

Trap: (options C and D) assumes the capacitor had charged to the full source voltage, ignoring the 100 kΩ divider. Option (A) swaps the 0.5 s and final values: an RC response never overshoots. A time-step simulation gives 8.00 V just after the step, 26.36 V at 0.5 s and 28.00 V at the end.

Where this shows up in industry

An RC filter in front of an ADC or a sensor input behaves this way: after a step the reading needs about to come within 1% of the final value (here ), which sets how fast the system can sample after a change.

From GATE prep to a electrical modelling and simulation career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.