GATE Electrical: Power Electronics (devices, rectifiers, power factor), previous-year questions solved

Real Power Electronics questions from the last five GATE Electrical papers, part 1: choosing power devices, diode and thyristor rectifiers (including a mixed bridge worked switch by switch), input power factor with harmonics, triac AC voltage control and a converter-fed DC motor in regenerative braking. Each one has a step-by-step solution that matches the official answer key, the traps that cost marks, and where the idea shows up in real converter work. Commutation, choppers, DC-DC converters and inverters are on the second Power Electronics page (linked on this page).

Questions from official GATE EE papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 16 Nov 2026 · 16 questions

GATE 2022 · EE · Q.22MCQ · 1 markPower semiconductor devices

100 W laptop charger switching at 200 kHz: which power device suits it best?

A charger supplies 100 W at 20 V for charging the battery of a laptop. The power devices, used in the converter inside the charger, operate at a switching frequency of 200 kHz. Which power device is best suited for this purpose?
  1. (A)IGBT
  2. (B)Thyristor
  3. (C)MOSFET
  4. (D)BJT

Answer: (C) Official key: C

  1. Two numbers decide it: low power (100 W, so a few amperes at 20 V) and a high switching frequency (200 kHz, a period).
  2. A thyristor cannot be turned off by its gate and is used at line frequency. A BJT is current-driven with slow storage-time turn-off (tens of kHz at best). An IGBT has a tail current at turn-off that keeps it below roughly 50 kHz in practice.
  3. A power MOSFET is a majority-carrier device: no stored charge, voltage-driven gate, switching in tens of nanoseconds. At low voltage and low power it is the only device here that switches efficiently at 200 kHz.
  4. MOSFET: option (C).

Trap: picking the IGBT because it is the 'modern' device. IGBTs win at high voltage and high current (inverters, traction), not at 20 V and 200 kHz.

Where this shows up in industry

Every USB-C and laptop adapter is a MOSFET flyback or resonant converter switching at 100 kHz to over 1 MHz; GaN transistors are now pushing that higher to shrink the magnetics. IGBTs are used where the voltage is hundreds of volts and the frequency is low, such as EV traction inverters at about 10 kHz.

GATE 2024 · EE · Q.27MCQ · 1 markPower semiconductor devices

SCR, GTO, IGBT or power MOSFET: which is the fastest switch at similar ratings?

If the following switching devices have similar power ratings, which one of them is the fastest?
  1. (A)SCR
  2. (B)GTO
  3. (C)IGBT
  4. (D)Power MOSFET

Answer: (D) Official key: D

  1. Speed is set by how much stored minority charge must be removed at turn-off.
  2. SCR and GTO are four-layer bipolar devices with large stored charge: switching frequencies of the order of 1 kHz. The IGBT is bipolar in its drift region, so its turn-off has a current tail: tens of kHz.
  3. The power MOSFET conducts only with majority carriers: there is no stored charge to sweep out, so it switches in nanoseconds and works at hundreds of kHz.
  4. Power MOSFET: option (D).

Ranking to remember, slowest to fastest: SCR, GTO, BJT, IGBT, MOSFET (and today GaN/SiC above that).

Where this shows up in industry

Device choice is the first decision in converter design: switching frequency sets the size of every inductor and capacitor. That is why data-centre and telecom supplies use MOSFETs (or GaN), while HVDC links still use thyristors switching at 50 Hz.

GATE 2023 · EE · Q.26MSQ · 1 markPower semiconductor devices

Which switch combinations block one voltage polarity but carry current both ways?

A semiconductor switch needs to block voltage of only one polarity () during OFF state as shown in figure (i) and carry current in both directions during ON state as shown in figure (ii). Which of the following switch combination(s) will realize the same?
[Figure (i): an open switch between P and Q with at P. Figure (ii): the closed switch carrying current either way. The options are drawn in the paper; described here, with the IGBT's collector towards P in every option.]
  1. (A)An IGBT with a diode in antiparallel (the diode conducts from Q to P).
  2. (B)The IGBT with its antiparallel diode, in series with a diode that conducts from Q to P.
  3. (C)The IGBT with its antiparallel diode, in series with a diode that conducts from P to Q.
  4. (D)The IGBT with its antiparallel diode in series with a diode that conducts from P to Q, and the whole branch bypassed by a diode that conducts from Q to P.

Answer: (A) and (D) Official key: A, D

  1. OFF, with P positive: no path may conduct from P to Q. ON: there must be a path P to Q and a path Q to P.
  2. (A): P to Q through the IGBT when it is on, Q to P through the diode. With the IGBT off, the diode is reverse biased by , so it blocks. Works.
  3. (B): the series diode only conducts Q to P, so no current can ever flow P to Q. Fails the ON test.
  4. (C): the series diode only conducts P to Q, so the antiparallel diode is useless and Q to P is blocked. Fails.
  5. (D): P to Q through the IGBT and the series diode; Q to P through the outer diode; OFF, the IGBT blocks P to Q. Works.
  6. (A) and (D).

We checked each option as a network of one-way elements: only (A) and (D) give 'no P to Q path when off' and 'both directions when on'.

Where this shows up in industry

This is the 'asymmetric blocking, bidirectional current' switch inside every voltage-source inverter leg: the IGBT plus freewheeling diode lets motor current flow back to the DC link. Option (D) is how matrix converters and current-source converters build switches that also need series blocking.

GATE 2026 · EE · Q.27MCQ · 1 markPower semiconductor devices

Power diode with a straight-line forward characteristic: what is the loss at 15 A?

The figure shows a straight-line approximation for the forward characteristics of a power diode. A continuous on-state current of 15 A is flowing through the diode. What is the power loss in the diode?
Power diode forward characteristic: a straight line starting at 1.0 V and 0 A and passing through 1.8 V at 50 A5001.01.8On-state voltage (V)On-state current (A)
  1. (A)32.8 W
  2. (B)21.2 W
  3. (C)18.6 W
  4. (D)23.1 W

Answer: (C) Official key: C

  1. Read the model off the figure: threshold and slope resistance .
  2. At 15 A: .
  3. .
  4. 18.6 W: option (C).

Trap: using 1.8 V (the voltage at 50 A) gives , and treating 1.0 V as the drop alone gives 15 W. For a current that is not constant, the same model gives .

Where this shows up in industry

This threshold-plus-resistance model is exactly what datasheets give (VT0 and rT) and what engineers use to size heat sinks for rectifiers and freewheeling diodes; conduction loss is usually the larger share of diode loss in line-frequency rectifiers.

GATE 2022 · EE · Q.32NAT · 1 markDiode and thyristor rectifiers

Full-bridge diode rectifier on a 50 Ω resistor from 200 V: how much power does the load take?

A single-phase full-bridge diode rectifier feeds a resistive load of 50 Ω from a 200 V, 50 Hz single phase AC supply. If the diodes are ideal, then the active power, in watts, drawn by the load is _____________. (round off to nearest integer).

Answer: 800 W Official key: 795 to 805

  1. The full bridge only flips the negative half cycles, so the load voltage is .
  2. Squaring removes the sign: the RMS of equals the RMS of , 200 V.
  3. .

Trap: using the average output voltage gives . Power in a resistor always uses RMS. Our numerical integration of over a cycle gives 800.0 W.

Where this shows up in industry

The same RMS-versus-average distinction decides heater and lamp ratings fed from rectifiers, and it is why a DC meter (which reads the average) under-reports the heating effect of rectified waveforms.

GATE 2022 · EE · Q.59NAT · 2 marksDiode and thyristor rectifiers

Half-controlled bridge at 45° with 15 A ripple-free load current: what is the fundamental source current amplitude?

For the ideal AC-DC rectifier circuit shown in the figure below, the load current magnitude is A and is ripple free. The thyristors are fired with a delay angle of 45°. The amplitude of the fundamental component of the source current, in amperes, is __________. (round off to two decimal places)
Single-phase half-controlled bridge: two thyristors in the top (common-cathode) group, two diodes in the bottom group, AC source between the two leg midpoints, a series R-L load carrying a ripple-free current Idc+Idc

Answer: 17.64 A Official key: 17.3 to 18

  1. Thyristors on top, diodes at the bottom: a half-controlled bridge. From to the source supplies ; from to the load freewheels through a thyristor and a diode in the same leg, so the source current is zero; from to it is .
  2. That is a quasi-square wave of width . Its fundamental amplitude is
  3. .

Trap: answering the RMS () when the question asks for the amplitude, or using the full-converter result , which ignores the freewheeling gap. Our numerical Fourier series of the waveform gives 17.645 A.

Where this shows up in industry

Half-controlled bridges are used in DC motor drives and battery chargers because freewheeling improves the input power factor compared with a fully controlled bridge at the same firing angle; the fundamental current calculated here sets that displacement and distortion.

GATE 2023 · EE · Q.58NAT · 2 marksDiode and thyristor rectifiers

Bridge with three thyristors and one diode, fired at 60° and 240°: what is the average load voltage?

The single phase rectifier consisting of three thyristors , , and a diode feed power to a 10 A constant current load. and are fired at and is fired at . The reference for is the positive zero crossing of . The average voltage across the load in volts is _____ (Round off to 2 decimal places).
Single-phase bridge: left leg thyristor T1 (top) and T2 (bottom), right leg diode D1 (top) and thyristor T3 (bottom); source Vin = 100 sin(100 pi t) V between the left and right leg midpoints, plus terminal on the left; a 10 A constant current load across the output VoT₁D₁T₂T₃+10 AVO+−

Answer: 39.79 V Official key: 39 to 40.5

  1. Name the leg midpoints P (left, source +) and Q (right), so . The top group is (from P) and (from Q); the bottom group is (to P) and (to Q). The current-source load always needs one top and one bottom device on.
  2. to : and conduct, .
  3. At Q rises above P, so the diode takes over from naturally. and short the load through the right leg: from to .
  4. At fires (P is now the lowest point) and takes over from : and give . With no thyristor fired at this pair keeps conducting until , fire at , so from to (negative for the last ).
  5. Average over one cycle: and , so .

Trap: assuming and stop at . Nothing commutates them until the next firing, so the output goes negative between and . A switch-by-switch simulation of the bridge over three cycles gives the same 39.79 V.

Where this shows up in industry

Mixed bridges like this are what you get when one device fails or is replaced by a diode for cost; working out which pair conducts in each interval is exactly how fault waveforms on real converters are diagnosed with an oscilloscope.

GATE 2025 · EE · Q.48MCQ · 2 marksDiode and thyristor rectifiers

Converter with Vo = 400(1 + cos α/3) feeding R-L-E: which firing angle gives 64 W in the resistor?

In the following circuit, the average voltage where is the firing angle. If the power dissipated in the resistor is 64 W, then the closest value of in degrees is
Three-phase star-connected source feeding a three-phase thyristor converter whose DC output Vo drives a 1 ohm resistor, a 100 mH inductor and a 500 V battery in series, battery positive towards the converter positive3-phase thyristor converter++−Vo1 Ω100 mH500 V
  1. (A)35.9
  2. (B)46.4
  3. (C)41.4
  4. (D)0

Answer: (A) Official key: A

  1. Resistor power gives the current: , so (the 100 mH inductor keeps it steady).
  2. The inductor has no average voltage, so .
  3. .
  4. : option (A).

Trap: forgetting the 500 V back-EMF and setting , which has no solution. Average voltages balance across R, L and E; only R dissipates.

Where this shows up in industry

A controlled rectifier charging a battery or driving a DC motor is controlled exactly like this: the firing angle sets the average voltage, and the small difference between it and the back-EMF divided by the resistance sets the current. That is why small changes in α make large changes in charging current.

GATE 2026 · EE · Q.34NAT · 1 markDiode and thyristor rectifiers

Diode in series with 500 µH and 10 Ω on a 325 V peak supply: what is the peak diode current?

Consider the circuit shown. Assume that the diode D is ideal. The supply voltage V, H, and . The peak diode current (in amperes) is ______________ (Round off to one decimal place)
Series circuit: source vs = 325 sin(2 pi 50 t) V, an ideal diode D, a 500 microhenry inductor and a 10 ohm resistorDL = 500 µHR = 10 Ωvₛ

Answer: 32.5 A Official key: 32.3 to 32.5

  1. Compare the reactance with the resistance: , tiny next to 10 Ω.
  2. So the load is almost purely resistive: and the load angle is only .
  3. Peak current .

We solved step by step through the conducting interval (diode off when the current returns to zero): the peak is 32.49 A, matching the shortcut. The inductor only delays the peak by about 0.05 ms and stretches conduction a little past .

Where this shows up in industry

Checking whether a reactance actually matters before reaching for the full transient solution is a standard engineering habit: a few hundred microhenries of wiring or filter inductance barely changes a 10 Ω load at 50 Hz, but it dominates at switching frequencies.

GATE 2026 · EE · Q.61NAT · 2 marksDiode and thyristor rectifiers

Diode charging a 50 V battery through 10 Ω from a 100 V peak supply: what is the average current?

Consider the circuit shown. Assume that the diode (D) is ideal. Given V, V, and , the average value of the current through the diode is ___________ A (Round off to two decimal places)
Series circuit: source vs = 100 sin(2 pi 50 t) V, an ideal diode D, a 10 ohm resistor and a 50 V battery whose positive terminal faces the resistorDR = 10 Ω+Vdc = 50 Vvₛ

Answer: 1.09 A Official key: 1.04 to 1.14

  1. The diode conducts only while : , i.e. from to .
  2. In that window .
  3. with
  4. and , so .

Trap: averaging over the conduction window only () instead of the full cycle triples the answer. Numerical averaging of the current over a full cycle gives 1.090 A.

Where this shows up in industry

This is the basic model of a battery charger without current control: current flows only near the voltage peak, so the RMS current (and the I2R heating in the wiring) is much higher than the average suggests. Real chargers add a controlled converter to fix that.

GATE 2022 · EE · Q.33NAT · 1 markInput current, harmonics and power factor

Sinusoidal 230 V supply with a 10 A fundamental and 3rd and 5th harmonics: what is the input power factor?

The voltage at the input of an AC-DC rectifier is given by where rad/s. The input current drawn by the rectifier is given by The input power factor, (rounded off to two decimal places), is, _________________ lag.

Answer: 0.45 lag Official key: 0.43 to 0.47

  1. The voltage is a pure sinusoid, so only the fundamental current carries real power: .
  2. Power factor .
  3. , , .
  4. lag.

The two factors have names: distortion factor 0.894 and displacement factor 0.5. Trap: answering 0.5 (displacement only). Integrating numerically gives 0.447.

Where this shows up in industry

Grid codes and standards such as IEC 61000-3-2 limit harmonic current because it raises RMS current (and losses) without delivering power; this is why every appliance above 75 W in Europe has power-factor correction in its front end.

GATE 2025 · EE · Q.27MCQ · 1 markInput current, harmonics and power factor

300 V sinusoidal supply, current with 3rd and 5th harmonics: which input power factor is closest?

The input voltage and current of a converter are given by, where, rad/s. The input power factor of the converter is closest to
  1. (A)0.845
  2. (B)0.867
  3. (C)0.887
  4. (D)1.0

Answer: (A) Official key: A

  1. Pure sinusoidal voltage: only the fundamental current makes real power, so .
  2. .
  3. .
  4. : option (A).

Trap: option (B) 0.867 is the displacement factor alone. The phase angles of the harmonics do not matter: harmonics at other frequencies average to zero power with a sinusoidal voltage.

Where this shows up in industry

Utilities bill large industrial users for poor power factor, and harmonic distortion counts against it as much as phase lag. Measuring both separately (displacement versus distortion) tells you whether to add capacitors or a harmonic filter.

GATE 2024 · EE · Q.62NAT · 2 marksInput current, harmonics and power factor

Half-controlled bridge at 60°: what is the ratio of fundamental to total RMS input current?

A single-phase half-controlled bridge converter supplies an inductive load with ripple free load current. The triggering angle of the converter is 60°. The ratio of the rms value of the fundamental component of the input current to the rms value of the total input current of the bridge is _________ (rounded off to 3 decimal places).

Answer: 0.955 Official key: 0.940 to 0.970

  1. Input current: from to , from to , zero during freewheeling: a quasi-square wave of width .
  2. Total RMS: .
  3. Fundamental RMS: .
  4. Ratio .

Trap: using the fully controlled bridge (square wave, no gap) gives . A numerical Fourier series of the waveform gives 0.955.

Where this shows up in industry

This ratio is the distortion factor; multiplied by the displacement factor cos(α/2) it gives the input power factor (0.83 here). Freewheeling is the reason half-controlled bridges are preferred in large DC drives that run at reduced voltage for long periods.

GATE 2024 · EE · Q.28MCQ · 1 markAC voltage control and converter-fed DC drives

Triac AC voltage controller on 10 Ω and 18.37 mH: what is the minimum firing angle for control?

A single-phase triac based AC voltage controller feeds a series RL load. The input AC supply is 230 V, 50 Hz. The values of R and L are 10 Ω and 18.37 mH, respectively. The minimum triggering angle of the triac to obtain controllable output voltage is
  1. (A)15°
  2. (B)30°
  3. (C)45°
  4. (D)60°

Answer: (B) Official key: B

  1. With an RL load the current lags the voltage by the load angle .
  2. , so .
  3. For the current from the previous half cycle is still flowing when the next gate pulse arrives, the triac stays on and the load sees the full sine wave: no control. Control starts at .
  4. : option (B).

The 230 V does not enter the answer; it is there to tempt a calculation.

Where this shows up in industry

Light dimmers, fan regulators and soft starters for induction motors are triac or antiparallel-thyristor controllers; with inductive loads they must be fired beyond the load angle, which is why fan regulators have a dead zone at the top of their range.

GATE 2025 · EE · Q.47MCQ · 2 marksAC voltage control and converter-fed DC drives

SCR fired at 0° into a 100 mH inductor from 230 V: what is the peak inductor current?

An ideal sinusoidal voltage source V feeds an ideal inductor through an ideal SCR with firing angle . If mH, then the peak of the inductor current, in ampere, is closest to
  1. (A)20.71
  2. (B)0
  3. (C)10.35
  4. (D)7.32

Answer: (A) Official key: A

  1. Once the SCR is on, , so starting from zero.
  2. The current never goes negative, so the SCR stays on for the whole cycle and the current reaches its peak at :
  3. : option (A).

Trap: option (C) 10.35 A is the steady-state AC amplitude . Starting a pure inductor at a voltage zero gives a fully offset current, twice that peak. Our step-by-step integration gives 20.71 A and the current returns to zero after exactly one cycle (20 ms).

Where this shows up in industry

This is the same doubling that causes transformer inrush current: energising a transformer at a voltage zero drives the core flux to twice its normal peak, saturating it. Controlled switching relays close breakers at the voltage peak to avoid it.

GATE 2024 · EE · Q.65NAT · 2 marksAC voltage control and converter-fed DC drives

Full converter regenerating a DC motor at 600 rpm with rated current: what triggering angle?

A single-phase full-controlled thyristor converter bridge is used for regenerative braking of a separately excited DC motor with the following specifications: rated armature voltage 210 V, rated armature current 10 A, rated speed 1200 rpm, armature resistance 1 Ω, input to the converter bridge 240 V at 50 Hz. The armature of the DC motor is fed from the full-controlled bridge and the field current is kept constant. Assume that the motor is running at 600 rpm and the armature terminals of the motor are suitably reversed for regenerative braking. If the armature current of the motor is to be maintained at the rated value, the triggering angle of the converter bridge in degrees should be ____________ (rounded off to 2 decimal places).

Answer: 114.62° Official key: 113.00 to 116.00

  1. Back EMF at rated speed: at 1200 rpm. Field constant, so at 600 rpm .
  2. Regenerating, the machine is a generator driving 10 A into the bridge: the bridge terminal voltage is , and with the armature reversed the bridge sees it as (inverting).
  3. Full converter: .
  4. .

Trap: adding (110 V) as in motoring gives . In regeneration the armature drop reduces the voltage reaching the converter.

Where this shows up in industry

Regenerative braking through a thyristor bridge running in inversion is how older DC traction, lifts and rolling mills return braking energy to the grid; the same α beyond 90° principle is used by HVDC inverter stations.

From GATE prep to a power electronics career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.