GATE Electronics (EC): Networks (nodal and mesh analysis, Thevenin and Norton, AC phasors and power, resonance, RL, RC and RLC transients, Laplace, two-port parameters), previous-year questions solved

Every networks question from the last five GATE Electronics and Communication papers, solved: nodal and mesh analysis, superposition, Thevenin and Norton with dependent sources, maximum power transfer, AC phasors, complex power and resonance, RL, RC and RLC switching transients, Laplace-domain analysis and two-port parameters. Each answer matches the official key and was recomputed by code from a numeric model of the network.

Questions from official GATE EC papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 17 Nov 2026 · 7 of 24 questions on this page

GATE 2022 · EC · Q.13MCQ · 1 markDC circuit analysis: nodal, mesh, superposition, Thevenin and Norton

5 V battery and 2 kOhm in the left branch, 2 kOhm to ground, 1 mA source with 2 kOhm: current I?

The current in the circuit shown is ________.
Resistive network. A 5 volt battery, plus terminal up, is in the left branch, and current I flows from it to the right through a 2 kilo-ohm resistor into the middle node. A 2 kilo-ohm resistor connects the middle node to ground. A 2 kilo-ohm resistor in series with a 10 to the minus 3 ampere current source, arrow pointing up, connects the middle node to ground on the right. The bottom wire is groundI2 kΩ2 kΩ2 kΩ5 V10−3 A
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (B) Official key: B

  1. Take the bottom wire as ground and let be the voltage at the middle node, where the three branches meet.
  2. The right branch is a resistor in series with an ideal current source. A current source fixes the branch current whatever the resistor is, so this branch simply pushes into node (the arrow points up, then the current turns left into ). The there does not change anything.
  3. KCL at , with resistances in and currents in : current in from the battery branch plus the source current equals the current down the middle resistor . So and .
  4. : option (B).
  5. Check by superposition. alone (current source open): . Current source alone (battery shorted): the splits equally between the middle resistor and the left branch, so flows leftwards through the , which is in the direction of . Sum: .

Trap: each of the other two answers is half of the superposition. Option (A), , is what the battery gives if you forget the current source. Option (C), , is what the current source gives if you forget the battery. The code solved the node equation with numpy and both partial cases: V, mA, battery alone 1.25 mA, source alone -0.50 mA. With the battery turned round the current would be -1.75 mA, which is not an option.

Where this shows up in industry

Superposition is how designers split a node's behaviour into a supply contribution and a load or bias-current contribution, for example a regulator's output set by its reference and a sink current from the load. Always checking each source alone catches a missing term.

GATE 2022 · EC · Q.14MCQ · 1 markDC circuit analysis: nodal, mesh, superposition, Thevenin and Norton

Two halves with 3 V sources joined only by a 10 Ohm resistor, ground on the left half only: current I?

Consider the circuit shown in the figure. The current flowing through the resistor is _________.
Two resistive halves joined only by a 10 ohm resistor with current I flowing left to right. Left half: a 3 volt battery, plus up, a 1 ohm resistor to the top node, a 2 ohm resistor from that node to the bottom wire, and the bottom wire is grounded. Right half: the 10 ohm resistor meets a node with a 1 ohm resistor to the right bottom wire and a 2 ohm resistor to a 3 volt battery, plus up, whose negative end joins the right bottom wire. The two bottom wires are not connected to each otherI10 Ω1 Ω2 Ω2 Ω1 Ω3 V3 V+−+−
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (B) Official key: B

  1. Look at how the circuit is wired. The left half (3 V battery, , ) has its bottom wire grounded. The right half (3 V battery, , ) has its own bottom wire, and the drawing leaves a gap: the two bottom wires are not connected. The ground symbol belongs to the left half only.
  2. So the only link between the two halves is the resistor. Draw a closed surface around the right half. The only wire crossing it is the resistor, and by KCL the net current entering the surface must be zero. Therefore .
  3. Each half then works as an isolated loop. The left half sits with at the end of the resistor (a divider ). The right half circulates its own current, , around its loop. Neither can push current through the resistor, because it has no return path.
  4. : option (B).

Trap: reading the figure as if the two bottom wires were joined (a common ground) and doing the usual two-source analysis. Then each half is a Thevenin source: behind on the left and behind on the right, so . That is about and the nearest option is (C), . The code solved the nodal equations both ways: with the gap in the bottom wire A, with the wires joined A.

Where this shows up in industry

Galvanic isolation works because two circuits with no shared return path cannot exchange current. Floating sensor grounds, isolated gate drivers and optocoupled signals all rely on this, and an accidental ground path between them is what creates a ground loop.

GATE 2023 · EC · Q.32NAT · 1 markDC circuit analysis: nodal, mesh, superposition, Thevenin and Norton

DC circuit with a 2 V source, two 1 mA current sources and kOhm resistors: current in the 200 Ohm resistor?

In the circuit shown below, the current flowing through resistor is ______ mA (rounded off to two decimal places).
Circuit with a 2 volt source and three current sources. The top-left node connects, going right, to the plus terminal of a 2 volt source whose minus terminal goes through a 2 kilo-ohm resistor to the bottom wire, to a 2 kilo-ohm resistor to the bottom wire, and to a 1 milliampere current source pointing up from the bottom wire into this node. From this node a 1 kilo-ohm resistor, in parallel with a 1 milliampere current source pointing right, leads to a second node. That node connects to the bottom wire through a 200 ohm resistor. The current i flows down through the 200 ohm resistor+−2 V2 kΩ2 kΩ1 mA1 kΩ1 mA200 Ωi

Answer: Official key: 1.30 to 1.40

  1. Use nodal analysis in units of , and . Take the bottom wire as ground. Let be the top-left node and the top of the resistor. The resistor is .
  2. Node . Leaving : the middle takes , the branch with the source and its series takes , the takes , and the top current source takes . Entering : the upward source. So , which simplifies to .
  3. Node . The top source delivers into , and the delivers . They leave through the : , so .
  4. Substitute: , so and (and ).
  5. , which is .

Trap: the series and the source form one branch to ground, and the source in parallel with the is a current source that pushes into . Leaving out the branch gives , and reversing the top source gives . Both are outside the official range to . The code solved the two nodal equations with numpy and again by superposition (each source on its own) with sympy: both give 1.3636 mA.

Where this shows up in industry

Nodal analysis with current sources and series resistors is how bias networks and sensor front ends are checked by hand before SPICE. A current source feeding a resistor ladder, as here, is the core of a DAC output stage or an LED driver.

GATE 2024 · EC · Q.31NAT · 1 markDC circuit analysis: nodal, mesh, superposition, Thevenin and Norton

5 mA and 2 mA sources, 1000 I0 controlled voltage source, three 1 kOhm resistors: Ix in mA?

In the given circuit, the current (in mA) is ______.
DC circuit with a controlled source. Along the top rail from left to right: a 5 mA current source pointing up at the far left, then node A with a 1 kilo-ohm resistor down to the bottom rail carrying current I0 downward, then a current-controlled voltage source 1000 times I0 with its minus terminal on the left and plus on the right, then node B. From node B a 1 kilo-ohm resistor in series with a 2 mA current source pointing down goes to the bottom rail, and a second 1 kilo-ohm resistor carries current Ix downward to the bottom rail−+1000 I0 5 mA1 kΩI01 kΩ2 mA1 kΩIx

Answer: Official key: 2 to 2

  1. Work in and so that voltages come out in volts. Call the top of the source and of the first resistor node A, and the node joining the other two resistors node B. The controlled source has its plus terminal towards B, so . With in mA this is volts.
  2. The first resistor gives . So .
  3. The right-hand resistor gives .
  4. The middle branch is a resistor in series with a source, so it carries exactly down, whatever is. KCL at B: the current coming through the controlled source is .
  5. KCL at A: the from the source splits into and . , so and .
  6. . Check: , , , and at A, at B.

Trap: assuming all flows through the first resistor, so , gives and . That forgets that the controlled source also carries part of the to the right. The code solved the three node equations with numpy and with sympy. Both give , and the wrong path lands outside the key.

Where this shows up in industry

A voltage that depends on a current in another branch is the transresistance model of a transimpedance amplifier or of a current-sense stage. Writing the node equations by hand, with the controlled source as an extra equation, is how engineers sanity-check a SPICE result before trusting it.

GATE 2024 · EC · Q.62NAT · 2 marksDC circuit analysis: nodal, mesh, superposition, Thevenin and Norton

50 V source, 2 and 3 Ohm branch, controlled source Vx with 2 Ohm: RL for maximum power in Ohm?

In the network shown below, maximum power is to be transferred to the load . The value of (in ) is ________ .
DC network with a controlled source. A 50 volt source has its plus terminal at the top left. From the top left node, a 2 ohm and a 3 ohm resistor in series run to the top right node (Vx is the voltage across the 3 ohm resistor, plus on the right). A second branch from the same node has a controlled voltage source Vx (minus on the left, plus on the right) in series with a 2 ohm resistor to the same top right node. The load RL connects from the top right node to the bottom wire, which returns to the minus of the source2 Ω3 Ω−Vx+−+Vx2 Ω+−50 VRL

Answer: Official key: 2.5 to 2.5

  1. Maximum power goes to the load when equals the Thevenin resistance seen at the load terminals, . So find the Thevenin equivalent of everything except .
  2. Let be the voltage at the top of and . The first branch ( in series) carries from left to right. The current enters the resistor at its minus end, so .
  3. The second branch starts at , the controlled source adds , so the right end of the source is at . Through the resistor: .
  4. The load receives . Rearranged: . That is a Thevenin source of in series with .
  5. The load for maximum power is . At that value the power is .

Trap: switching off the controlled source along with the independent one. Treating it as a short gives , and treating it as an open circuit gives . A controlled source must stay in the circuit when is found, so a test source is used instead. Both wrong values are outside the key. The code found with a test current and the source killed, from the open circuit, and the load power peaks at in a sweep.

Where this shows up in industry

Matching the load to the source resistance for maximum power is the idea behind 50 ohm RF chains and antenna matching networks. In power supplies and batteries the matched point is avoided, because half of the power is then lost inside the source resistance.

GATE 2025 · EC · Q.19MCQ · 1 markDC circuit analysis: nodal, mesh, superposition, Thevenin and Norton

Resistive network: 8 V terminal, 2 and 1 ohm to a node fed by 1 A through 3 ohm from 9 V. Voltage at node X?

Consider a part of an electrical network as shown below. Some node voltages, and the current flowing through the resistor are as indicated.

The voltage (in Volts) at node is ______.
Part of a resistive network. A left terminal at 8 V connects through 2 ohm to node X, then 1 ohm to a junction. A terminal at 9 V connects through a 3 ohm resistor, with 1 A flowing down from the 9 V terminal, to the same junction. From the junction, a 2 ohm resistor leads to a delta of three 2 ohm resistors that continues to the right.8 VX2 Ω1 Ω9 V3 Ω1 A2 Ω2 Ω2 Ω2 Ω
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. Call the junction where the , and right-hand resistors meet node . The terminal is at the top end of the resistor, and flows down through it into .
  2. KVL across the resistor: the drop is , so .
  3. The and resistors on the left are in series, in all, between the terminal and . Their current is , towards . Nothing else is connected at , so this is also the current in the resistor.
  4. KVL across the resistor: , option (A). The same value follows from KCL at : gives .
  5. The delta of resistors on the right never enters the answer. KCL at says the right-hand network simply takes .

Trap: reading the as flowing up the resistor, which puts and gives , option (B). The arrow in the figure points down, away from the terminal. Option (D), , is the branch current in amperes, not a voltage. The code solved KCL at with numpy for and got , cross-checked it by the series-chain current, and confirmed that the reversed-current reading lands exactly on (B).

Where this shows up in industry

Working back from one known branch current to a node voltage is how a bench engineer checks a power rail: measure the drop across a sense or series resistor, then add it to the voltage at the other end. The same KCL and KVL bookkeeping is used on resistor networks in supply distribution and in sensor bias chains.

GATE 2026 · EC · Q.30NAT · 1 markDC circuit analysis: nodal, mesh, superposition, Thevenin and Norton

1 mA source into two 1 kOhm dividers with a 6 V battery between the middle nodes: output voltage Vo?

The output voltage (in Volt) for the network given in the Figure is __. (rounded off to two decimal places)
Resistor network. A 1 mA current source drives its upward arrow into the top wire. Two 1 kilo-ohm resistors hang from the top wire, each in series with another 1 kilo-ohm resistor to the bottom wire. A 6 volt battery, positive on the left, joins the two middle nodes. The output voltage V_o is taken from the top wire (plus) to the bottom wire (minus)1 mA1 kΩ1 kΩ1 kΩ1 kΩ6 V+−Vo

Answer: Official key: 0.95 to 1.05

  1. Call the top wire (this is , since the bottom wire is the reference) and the two middle nodes and . Currents in mA, resistances in , so voltages come out in volts.
  2. KCL at : the source pushes in and it leaves through the two upper resistors: .
  3. The battery forces but carries an unknown current from to . Add the KCL equations of and and the battery current cancels: , that is , so .
  4. Put this in the first equation: , so .
  5. The battery only fixes with : and . It pushes the two middle nodes apart by equal and opposite amounts, so it does not change the top-rail voltage. By superposition the source alone gives (four in a bridge, battery replaced by a short, ), and the battery alone gives at .

Trap: reading off a middle node (3.5 V or -2.5 V) or adding the battery (). All are outside the official range 0.95 to 1.05. The code solved the modified nodal equations with the battery as an extra unknown for both polarities: = 1.000 V either way. Superposition gave 1.000 V from the source and 0.000 V from the battery.

Where this shows up in industry

A floating bias source between two nodes of a symmetric network shifts them in opposite directions and leaves the common-mode level alone. Analysts use this symmetry for bridge sensors, differential pairs with a floating bias and isolated supplies, to find which voltages the bias does and does not move.

From GATE prep to a power electronics or hardware design career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.