GATE Electrical: Signals and Systems (signal operations, system properties, convolution), previous-year questions solved

Real Signals and Systems questions from the last five GATE Electrical papers, part 1 (the time domain): the sifting property, energy and periodicity, linearity, time invariance, causality, BIBO stability, impulse responses and convolution. Each solution matches the official answer key, names the trap that costs marks, and shows where the idea is used in real engineering. Fourier series, Fourier, Laplace and Z-transforms and sampling are on part 2.

Questions from official GATE EE papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 16 Nov 2026 · 13 questions

GATE 2025 · EE · Q.21MCQ · 1 markSignal operations, energy and periodicity

x(t) = −t² on (−4, 4): what is the integral of x(t) δ(t + 3)?

Consider a continuous-time signal where is the continuous-time unit step function. Let be the continuous-time unit impulse function. The value of is
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. Sifting property: . Here sits at .
  2. lies inside the window , so the step bracket equals 1 there.
  3. : option (A).

Two traps: reading as an impulse at (same answer here only by luck, because is even), and dropping the minus sign in front of , which gives (B). Checked numerically with a narrow unit-area pulse in place of .

Where this shows up in industry

The impulse is how instruments and models are characterised: hammer-tap tests on a structure, a step or pulse injected into a motor drive, or a unit-impulse block in Simulink. Sampling a signal at one instant, which is what an ADC does, is the sifting property in hardware.

GATE 2024 · EE · Q.53NAT · 2 marksSignal operations, energy and periodicity

x(t) has energy E. What multiple of E is the energy of 2x(2t − 1)?

If the energy of a continuous-time signal is and the energy of the signal is , then is _____ (rounded off to 1 decimal place).

Answer: Official key: 2.0 to 2.0

  1. Energy of : .
  2. Substitute , so : the integral becomes .

Rule to remember: amplitude multiplies energy by ; compressing time by divides it by ; a time shift changes nothing. So . We confirmed it by integrating a test signal and its transformed copy numerically (ratio 2.000).

Where this shows up in industry

Energy and power bookkeeping under time scaling matters whenever a recorded signal is replayed faster or resampled: vibration and audio data, test-rig recordings sped up for analysis, or sensor logs decimated before storage.

GATE 2023 · EE · Q.49NAT · 2 marksSignal operations, energy and periodicity

x[n] = 1 + 3 sin(15πn/8 + 3π/4) − 5 sin(πn/3 − π/4): what is the period N?

The period of the discrete-time signal described by the equation below is _____ (Round off to the nearest integer).

Answer: Official key: 48 to 48

  1. A discrete sinusoid repeats after samples when for an integer , so must be an integer.
  2. First term: , : smallest integer is (with ).
  3. Second term: , : smallest is .
  4. The sum repeats when both do: .

Trap: computing and treating it as the period. In discrete time the period must be a whole number of samples. A brute-force search over also stops first at 48.

Where this shows up in industry

When a controller or DSP samples several tones at once (mains harmonics, gear-mesh and shaft frequencies), the combined sample pattern only repeats after the LCM of the individual periods. That is why FFT frame lengths are chosen to hold whole periods, otherwise the spectrum leaks.

GATE 2022 · EE · Q.48MCQ · 2 marksSystem properties

y(t) = x(eᵗ): is the system linear? Is it causal?

Consider the system as shown below (a block with input and output ) where . The system is
  1. (A)linear and causal.
  2. (B)linear and non-causal.
  3. (C)non-linear and causal.
  4. (D)non-linear and non-causal.

Answer: (B) Official key: B

  1. Linear: the input gives . The system only reads the input at another instant, so superposition holds.
  2. Causal? The output at time uses the input at time . Since for every real (for example reads ), the output always depends on a future input.
  3. So the system is linear and non-causal: option (B).

Trap: thinking that only negative times look ahead. Even at the system reads , a later instant. Our check fed two inputs that agree up to and differ after it: the outputs differed at for every tried.

Where this shows up in industry

Non-causal operations are fine offline: post-processing a recorded crash test or flight log can look ahead (zero-phase filtering in MATLAB's filtfilt does exactly this). A real-time controller cannot, which is why control filters always add delay.

GATE 2024 · EE · Q.37MCQ · 2 marksSystem properties

y(t) = e^(−t) ∫ from −∞ to t of e^τ x(τ) dτ: linear, time-invariant, causal?

The input and the output of a system are related as . The system is
  1. (A)nonlinear.
  2. (B)linear and time-invariant.
  3. (C)linear but not time-invariant.
  4. (D)noncausal.

Answer: (B) Official key: B

  1. Move inside: .
  2. That is a convolution with : the weight depends only on .
  3. Every convolution is linear and time-invariant, and for makes it causal too. Option (B).

Trap: seeing the factor outside the integral and calling the system time-varying (option C). A time-varying gain outside is cancelled here by the inside. We checked it numerically: shifting the input by 1.5 s shifted the output by exactly 1.5 s, and the output matched a direct convolution with .

Where this shows up in industry

This is the first-order low-pass filter written in the time domain: an RC filter on a sensor line, or the exponential moving average used to smooth current and temperature readings in battery management and motor-control firmware.

GATE 2024 · EE · Q.38MCQ · 2 marksSystem properties

T₁ sums x[0..n]; T₂ sums x[k]/2ᵏ. Which is BIBO stable?

Consider the discrete-time systems and defined as follows: Which one of the following statements is true?
  1. (A) and are BIBO stable.
  2. (B) and are not BIBO stable.
  3. (C) is BIBO stable but is not BIBO stable.
  4. (D) is not BIBO stable but is BIBO stable.

Answer: (D) Official key: D

  1. is an accumulator. The bounded input gives , which grows without limit, so is not BIBO stable.
  2. For , let . Then for every : bounded, so is BIBO stable.
  3. Option (D).

Note that is not time-invariant (the weight depends on the absolute index ), so you cannot use the LTI test directly. Bound the output itself, as above. With 200 random inputs bounded by 1, the output of never exceeded 2.

Where this shows up in industry

A pure accumulator is the integrator in every PI controller, and it is exactly why integrator wind-up happens: a sustained error makes the sum grow without bound. Drive and process controllers clamp or bleed the integrator for this reason.

GATE 2025 · EE · Q.42MCQ · 2 marksSystem properties

An LTI system's impulse response is u(t). Is every bounded input safe?

The continuous-time unit impulse signal is applied as an input to a continuous-time linear time-invariant system . The output is observed to be the continuous-time unit step signal . Which one of the following statements is true?
  1. (A)Every bounded input signal applied to results in a bounded output signal.
  2. (B)It is possible to find a bounded input signal which when applied to results in an unbounded output signal.
  3. (C)On applying any input signal to , the output signal is always bounded.
  4. (D)On applying any input signal to the output signal is always unbounded.

Answer: (B) Official key: B

  1. The impulse response is , so the system is an integrator: .
  2. BIBO stability needs . Here diverges, so the system is not BIBO stable.
  3. A concrete bounded input that breaks it: gives , which grows without limit (our numerical convolution gives ). Option (B).

(D) is too strong: a zero input or a short pulse gives a bounded output. Unstable means some bounded input blows up, not every input.

Where this shows up in industry

Integrators appear wherever position is obtained from velocity or charge from current: an IMU integrating gyro rate drifts without bound from a tiny constant bias, and coulomb counting in a battery pack drifts the same way, which is why both are periodically re-referenced.

GATE 2022 · EE · Q.46MCQ · 2 marksImpulse response and convolution

y(t) + (1/4) dy/dt = 2x(t): what is the impulse response?

Let a causal LTI system be governed by the following differential equation , where and are the input and output respectively. Its impulse response is
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (D) Official key: D

  1. Laplace transform with zero initial conditions: .
  2. .
  3. Causal inverse transform: : option (D).

Trap: reading the as the decay rate, which gives (A) or (C). Normalise the derivative coefficient to 1 first: . Time-stepping the equation for a unit step and differentiating the result gives , matching .

Where this shows up in industry

First-order models like this describe an RC sensor filter, a thermocouple's lag or a motor's electrical time constant. Engineers identify from a measured step or pulse response and then tune the controller around it.

GATE 2023 · EE · Q.17MCQ · 1 markImpulse response and convolution

dy/dt + 3y = 2x, initially at rest: what is the impulse response?

A continuous-time system that is initially at rest is described by where is the input voltage and is the output voltage. The impulse response of the system is
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (C) Official key: C

  1. (zero initial conditions, since the system starts at rest).
  2. : option (C).

Option (D) has the right shape but no : it would be non-zero before the impulse arrives, which a system initially at rest cannot do. Options (A) and (B) swap the gain and the pole. Numerical check: .

Where this shows up in industry

An RC low-pass on an ADC input is exactly this equation. Its impulse response tells the firmware engineer how long a spike on the sensor line takes to die out, which sets how soon after a disturbance a reading can be trusted.

GATE 2025 · EE · Q.20MCQ · 1 markImpulse response and convolution

h[n] = 1 for n = 0, 1, 2 and 0 otherwise: what is y[n] for an input x[n]?

Consider a discrete-time linear time-invariant (LTI) system , where . Let where is the discrete-time unit impulse function. For an input signal , the output is
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. For an LTI system, .
  2. Only are non-zero, so : option (A).

Trap: writing instead of , which gives (C), a non-causal system. Since for the system must be causal, so any option using is out. Checked by convolving a random input with .

Where this shows up in industry

This is a 3-tap moving-sum (moving-average) FIR filter, the simplest digital filter there is. Embedded firmware uses it to smooth ADC readings from current, temperature and position sensors.

GATE 2023 · EE · Q.31NAT · 1 markImpulse response and convolution

A unit pulse on (−1, 1) convolved with a ramp from −2 to 2 on (1, 5): when is the output largest?

For the signals and shown in the figure, is maximum at . Then in seconds is _____ (Round off to the nearest integer).
Two plots. Top: y(t) is zero up to t = 1 s, jumps to minus 2 at t = 1, rises in a straight line through zero at t = 3 to plus 2 at t = 5, and is zero after t = 5. Bottom: x(t) is a rectangular pulse of height 1 from t = minus 1 to t = plus 1 and zero elsewherety(t)-2-1123456-22tx(t)-2-11234561

Answer: s Official key: 4 to 4

  1. is a unit pulse on , so : the area of inside a 2 s window centred at .
  2. On , : negative on , positive on , zero outside.
  3. The area is largest when the window covers only the positive part, , i.e. centred at s, where .

Check with the derivative: . Just before it is ; just after, the window's front edge passes where drops to 0, so turns negative. Our numerical convolution on a 0.01 s grid peaks at with .

Where this shows up in industry

A sliding window sum like this is a matched filter or moving integrator: radar and ultrasonic sensors find an echo by sliding a template over the received signal and looking for the peak of the convolution. The window position at the peak is the time of arrival.

GATE 2024 · EE · Q.15MCQ · 1 markImpulse response and convolution

y(t) = x(−t). What is always true of x(t) * y(t)?

Suppose signal is obtained by the time-reversal of signal , i.e., , . Which one of the following options is always true for the convolution of and ?
  1. (A)It is an even signal.
  2. (B)It is an odd signal.
  3. (C)It is a causal signal.
  4. (D)It is an anti-causal signal.

Answer: (A) Official key: A

  1. . This is the autocorrelation of .
  2. Replace by and substitute : .
  3. So the result is always even: option (A).

It cannot be odd, because for any non-zero signal. Causality depends on , so (C) and (D) are not always true. We checked with a deliberately lopsided test signal: to within .

Where this shows up in industry

Autocorrelation is how engineers find hidden periodicity in noisy data: bearing-fault detection in vibration signals, pitch detection in audio, and GPS receivers locking onto a satellite's code all look for peaks in this even function.

GATE 2025 · EE · Q.40MCQ · 2 marksImpulse response and convolution

x₁ has area 1.5 and x₂ has area 1: what is the area under x₁ * x₂?

Let continuous-time signals and be and Consider the convolution . Then is
  1. (A)1.5
  2. (B)2.5
  3. (C)3.5
  4. (D)4

Answer: (A) Official key: A

  1. Area property of convolution: . (In transform terms: .)
  2. Area of : a unit square plus a triangle, .
  3. Area of : a triangle of base 2 and height 1, .
  4. : option (A).

No need to compute the convolution itself, which is the trap that eats time in the exam. We computed it anyway, numerically: the area under comes out as 1.500.

Where this shows up in industry

The same rule says a filter's DC gain multiplies the area of whatever passes through it. Engineers use it to check a smoothing filter is normalised (taps summing to 1) so a sensor reading is not scaled up or down by the filtering.

From GATE prep to a controls and signal-processing career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.