GATE Electrical: Analog Electronics (diodes, Zener, BJT and MOSFET amplifiers, op-amps), previous-year questions solved

Real Analog Electronics questions from the last five GATE Electrical papers: ideal-diode and Zener circuits, a Zener pass-transistor regulator, BJT bias, MOSFET common-source, common-gate, source-follower and cascode stages, and op-amp circuits from integrators and clippers to difference and instrumentation amplifiers. Each solution matches the official answer key, names the trap that costs marks, and shows where the circuit is used in real hardware. Logic, counters, multiplexers and ADCs are on the Digital Electronics page.

Questions from official GATE EE papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 16 Nov 2026 · 16 questions

GATE 2022 · EE · Q.25MCQ · 1 markDiode and Zener circuits

Two ideal diodes in series with R1: when does the output follow the input?

For the circuit shown below with ideal diodes, the output will be
Ideal-diode circuit: the input's + terminal feeds D1, which conducts towards the top of R1 and the output's + terminal; the bottom of R1 returns to the input's minus terminal through D2, which conducts from R1 towards the input+−VinD1D2R1+−Vout
  1. (A) for
  2. (B) for
  3. (C) for
  4. (D) for

Answer: (A) Official key: A

  1. Follow the only loop: input + terminal, (pointing towards ), from top to bottom, (pointing back towards the input's minus terminal). Both diodes point the same way round the loop, so they conduct together or not at all.
  2. : both diodes are forward biased, the current flows down through and, with ideal diodes, .
  3. : both are reverse biased, no current flows, so (not and not ).
  4. Only statement (A) holds: option (A).

Trap: seeing two diodes and assuming a full-wave bridge, which would give option (D) as well. With only two diodes in series it is a half-wave circuit. We checked both diode states at several positive and negative inputs: exactly one state is consistent each time.

Where this shows up in industry

A diode in each leg of a supply line is how equipment is protected against a reversed battery or DC input: for the wrong polarity nothing conducts and the load sees zero volts instead of a negative voltage.

GATE 2024 · EE · Q.60NAT · 2 marksDiode and Zener circuits

+10 V divider, +3 V and two ideal diodes: what current flows through D1?

In the given circuit, the diodes are ideal. The current through the diode in milliamperes is ___________ (rounded off to two decimal places).
Ideal diodes: +10 V feeds a divider of two 1 kilohm resistors to ground; from the divider midpoint, D2 conducts to the right through 1 kilohm into node X; from +3 V, D1 conducts downward into X (current I); X goes to ground through 1 kilohm+10 V+3 VID11 kΩ1 kΩD21 kΩ1 kΩ

Answer: 1.67 mA Official key: 1.64 to 1.70

  1. Replace the 10 V divider by its Thevenin equivalent: behind .
  2. Assume both diodes on. ties the node X to 3 V. Then carries (positive, so is on).
  3. The 1 k from X to ground draws . KCL at X: , positive, so is on too.
  4. .

Trap: assuming is off because the 5 V side looks stronger. With off, the divider and the two 1 k resistors would only lift X to (the divider node sags to 4 V), below 3 V, so must conduct. We tested all four on/off combinations: only 'both on' is consistent.

Where this shows up in industry

This 'diode-OR' of two supplies is how a board picks the higher of two rails, for example USB 5 V and a 3.3 V regulator feeding the same node, and it is the first check in any power-path design.

GATE 2023 · EE · Q.59NAT · 2 marksDiode and Zener circuits

25 V, 7 kΩ base resistor, β = 99, a 5 V Zener: what current flows in the 20 Ω load?

The Zener diode in circuit has a breakdown voltage of 5 V. The current gain of the transistor in the active region in 99. Ignore base-emitter voltage drop . The current through the 20 Ω resistance in milliamperes is ________(Round off to 2 decimal places).
25 V supply. BJT (beta 99) with collector on the +25 V rail; its base is fed from the +25 V rail through 7 kilohm; the emitter goes through 10 ohm to a node N; the 5 V Zener has its cathode at the base and its anode at N; N goes to ground through 20 ohm+25 V7 kΩβ = 9910 Ω5 V Zener20 Ω

Answer: 250.00 mA Official key: 245 to 255

  1. The Zener sits between the base and node N (the top of the 20 ), cathode at the base. It only conducts if reaches 5 V. With ignored, is the drop across the 10 emitter resistor.
  2. Assume the Zener is off. Then all the base current comes through 7 k and the emitter current flows through .
  3. Base loop: , so and .
  4. Check: drop across 10 , so the Zener is indeed off. Current in the 20 .

Trap: assuming the Zener regulates because it is drawn there. If it were in breakdown, would be 0.5 A and the 7 k node balance would need a negative Zener current: impossible. We checked both Zener states; only 'off' is consistent.

Where this shows up in industry

The Zener here is a current limiter that has not tripped: if the load current pushed the drop across the 10 Ω sense resistor to 5 V, the Zener would steal base current and cap the output. The same idea, with a small transistor instead of a Zener, protects linear regulators and LED drivers from short circuits.

GATE 2026 · EE · Q.33NAT · 1 markDiode and Zener circuits

Zener and pass-transistor regulator from 10 V, 5.4 V Zener, 100 mA load: what is the best efficiency?

In the linear regulator circuit shown, the base to emitter voltage of the BJT is 0.6 V. The Zener diode clamps the base voltage to 5.4 V. Ignore the biasing current of the Zener diode and BJT.
The maximum possible efficiency of the regulator circuit is ___________ % (Round off to one decimal place)
Linear regulator: 10 V source; BJT collector on the 10 V rail; 5 kilohm from the rail to the base; a 5.4 V Zener from the base to ground (cathode at the base); the emitter is the output Vout, loaded by a constant current IL = 100 mA; VBE = 0.6 V+−10 V5 kΩ5.4 VIL+−VoutIL = 100 mAVBE = 0.6 V

Answer: 48.0 % Official key: 47.5 to 48.0

  1. Output: .
  2. A series pass regulator draws (almost) the load current from the input: with the bias currents ignored, .
  3. .

The load current cancels: a linear regulator's best efficiency is just . If you do count the through the 5 k resistor, you get 47.6 %, still inside the official range. Trap: using the Zener voltage 5.4 V as the output gives 54 %.

Where this shows up in industry

This is why linear regulators (LDOs) waste half their power when dropping 10 V to 5 V and are used only where the drop is small or noise matters, such as analog and RF rails; bigger drops go to a buck converter at 85 to 95 %.

GATE 2024 · EE · Q.42MCQ · 2 marksBJT and MOSFET amplifiers

Voltage-divider bias, 12 V, 100 kΩ / 50 kΩ, RC 2 kΩ, RE 1 kΩ, β = 100: what is the Q-point?

A BJT biasing circuit is shown in the figure, where V and . The Quiescent Point values of and are respectively
Voltage-divider bias: VCC = +12 V; R1 = 100 kilohm from VCC to the base and R2 = 50 kilohm from the base to ground; RC = 2 kilohm from VCC to the collector; RE = 1 kilohm from the emitter to groundVCC = +12 VIC+VCE−R1 = 100 kΩR2 = 50 kΩRC = 2 kΩRE = 1 kΩ
  1. (A)4.6 V and 2.46 mA
  2. (B)3.5 V and 2.46 mA
  3. (C)2.61 V and 3.13 mA
  4. (D)4.6 V and 3.13 mA

Answer: (A) Official key: A

  1. Thevenin at the base: , .
  2. Base loop: , so .
  3. , .
  4. : option (A).

Trap: ignoring the base current (stiff-divider shortcut) gives , close to the 3.13 mA decoy, and . Here is not small next to , so the shortcut is off by about 30 %. We solved the full nodal equations (no Thevenin step): , .

Where this shows up in industry

Divider bias with an emitter resistor is still how discrete BJT stages in sensor front ends and audio preamps are set up, because makes the Q-point almost independent of β, which varies two to one between transistors of the same part number.

GATE 2022 · EE · Q.12MCQ · 1 markBJT and MOSFET amplifiers

Ideal MOSFET common-drain amplifier: what is its small-signal current gain?

For an ideal MOSFET biased in saturation, the magnitude of the small signal current gain for a common drain amplifier is
  1. (A)0
  2. (B)1
  3. (C)100
  4. (D)infinite

Answer: (D) Official key: D

  1. In a common-drain stage (source follower) the input is the gate and the output current is the source current.
  2. An ideal MOSFET has an insulated gate: the small-signal gate current is zero (no gate leakage, and at low frequency no capacitive current).
  3. The output current is finite, so : option (D).

Trap: answering 1 by mixing it up with the voltage gain of a source follower, which is close to 1. We modelled the gate with a leakage conductance and let it go to zero: the current gain grows without limit.

Where this shows up in industry

Source followers are used as buffers precisely because they draw no input current: a high-impedance sensor, such as a piezo accelerometer or an electret microphone, can drive a long cable or an ADC through one without being loaded.

GATE 2025 · EE · Q.16MCQ · 1 markBJT and MOSFET amplifiers

Common-source and common-gate MOSFET amplifiers: which one inverts?

Which one of the following statements is true about the small signal voltage gain of a MOSFET based single stage amplifier?
  1. (A)Common source and common gate amplifiers are both inverting amplifiers
  2. (B)Common source and common gate amplifiers are both non-inverting amplifiers
  3. (C)Common source amplifier is inverting and common gate amplifier is non-inverting amplifier
  4. (D)Common source amplifier is non-inverting and common gate amplifier is inverting amplifier

Answer: (C) Official key: C

  1. Common source: the input raises , the drain current rises, and the drain falls by . Gain : inverting.
  2. Common gate: the input drives the source with the gate fixed. Raising the source lowers , the drain current falls, so the drain rises. Gain : non-inverting.
  3. Option (C).

Small-signal nodal check with , , : common source , common gate . Trap: assuming every single-transistor gain stage inverts. Only the common-source (and common-emitter) one does; followers and common-gate stages do not.

Where this shows up in industry

Common-gate stages sit at the input of RF low-noise amplifiers and in cascodes because they give voltage gain without the Miller effect that slows a common-source stage; knowing which stages invert is also what keeps a multi-stage feedback loop from turning into an oscillator.

GATE 2025 · EE · Q.38MCQ · 2 marksBJT and MOSFET amplifiers

Cascode M1 and M2 fed by an ideal current source: what is the output impedance?

In the circuit, is an ideal current source. The transistors and are assumed to be biased in saturation, wherein is the input signal and is fixed DC voltage. Both transistors have a small signal resistance of and trans-conductance of . The small signal output impedance of this circuit is
Cascode: ideal current source IDC from VDD into the output node Vout; NMOS M2 (gate at the fixed voltage VDC) from Vout down to the drain of NMOS M1 (gate driven by Vin), whose source is groundedVDDIDCVoutVDCVinM2M1
  1. (A)
  2. (B)
  3. (C)
  4. (D)infinity

Answer: (C) Official key: C

  1. Set the signals to zero: and become AC ground. The ideal current source is an open circuit, so it adds nothing in parallel.
  2. Looking down into 's drain you see (its gate is grounded). This sits in 's source.
  3. Apply at the output, current . The source of rises to , so . : .
  4. Rearranged: , so : option (C).

Trap: (D), because an ideal current source has infinite impedance. That source is in parallel with the transistors, and infinite in parallel with is just . We solved the small-signal nodal equations for three pairs; only (C) matched every time.

Where this shows up in industry

The cascode boosts output resistance by roughly (often 20 to 50 times), which is how op-amp gain stages and precision current mirrors in ICs reach open-loop gains of 80 to 100 dB.

GATE 2022 · EE · Q.16MCQ · 1 markOp-amp and wave-shaping circuits

Op-amp integrator with a 0.1 V DC input: where does the output settle?

The steady state output (), of the circuit shown below, will
Op-amp integrator: a 0.1 V DC source, positive terminal up, feeds R1 into the inverting input; capacitor C1 from the output back to the inverting input; the non-inverting input goes to ground through R2; supplies +VDD and -VEE−++VDD−VEE+−0.1 VVoutR1C1R2
  1. (A)saturate to
  2. (B)saturate to
  3. (C)become equal to 0.1 V
  4. (D)become equal to –0.1 V

Answer: (B) Official key: B

  1. The circuit is an inverting integrator: (no current enters the + input, so just keeps it at 0 V).
  2. A constant input makes the output ramp downward at volts per second, forever.
  3. A real output cannot go below the negative supply, so it ends up saturated at : option (B).

Trap: (D) treats it like a unity inverting amplifier; with a capacitor in feedback there is no DC feedback at all. We time-stepped the circuit with an op-amp of gain and rails (, ): the output ramps at about and sits at after 1.5 s.

Where this shows up in industry

This is integrator wind-up, the same problem that hits the I term of a PI controller: practical analog integrators get a large resistor across the capacitor, or a reset switch, and digital controllers clamp the integral (anti-windup).

GATE 2022 · EE · Q.44MCQ · 2 marksOp-amp and wave-shaping circuits

Ideal current amplifier with feedback Cf and output Cc: what is Iout/Iin?

The current gain in the circuit with an ideal current amplifier given below is
Current amplifier: input current source Iin from the inverting input node down to ground (arrow pointing down); capacitor Cf from the output back to the inverting input; non-inverting input grounded; the output drives capacitor Cc into a short to ground carrying Iout−+∞IinIoutCfCc
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (C) Official key: C

  1. The inverting input is a virtual ground. As drawn, flows out of that node down through the source, so the same current must arrive through from the output: , so .
  2. The output drives into a short to ground: .
  3. : option (C).

Trap: the sign. Reading the source as pushing current into the node gives (D); the arrow in the source points away from the node. The ratio of the two capacitive reactances is frequency-independent, so the gain is a pure number. Checked with a finite-gain model (gain ) at 1 kHz for three capacitor pairs.

Where this shows up in industry

Capacitive feedback around an op-amp is the charge amplifier used with piezoelectric force and vibration sensors: the output depends only on a capacitor ratio, not on cable capacitance or frequency.

GATE 2023 · EE · Q.37MCQ · 2 marksOp-amp and wave-shaping circuits

Inverting op-amp with diode and Zener feedback, 10 sin(1000t) input: what are the output limits?

Consider the OP AMP based circuit shown in the figure. Ignore the conduction drops of diodes and . All the components are ideal and the breakdown voltage of the Zener is 5 V. Which of the following statements is true?
Inverting op-amp stage with plus and minus 15 V supplies: Vin = 10 sin(1000t) V through 1 kilohm into the inverting input, non-inverting input grounded. Feedback branch 1: 1 kilohm in series with D1, D1 conducting from the inverting input towards the output. Feedback branch 2: Zener DZ with its anode at the inverting input, in series with D2, which conducts from the output towards the Zener−++15 V−15 V+Vin = 10 sin(1000t) VVO1 kΩ1 kΩD1DZD2
  1. (A)The maximum and minimum values of the output voltage are +15 V and -10 V, respectively.
  2. (B)The maximum and minimum values of the output voltage are +5 V and -15 V, respectively.
  3. (C)The maximum and minimum values of the output voltage are +10 V and -5 V, respectively.
  4. (D)The maximum and minimum values of the output voltage are +5 V and -10 V, respectively.

Answer: (D) Official key: D

  1. Positive input half: current flows into the virtual-ground node through the input 1 k and must leave towards the output. points that way, so the 1 k + branch conducts: a gain of , so , reaching . (The Zener branch is blocked by .)
  2. Negative input half: current must flow from the output into the node. blocks. The only path is forward and the Zener in reverse breakdown, which needs .
  3. Before the Zener breaks down there is no feedback, so the output jumps straight up to and is clamped there for the whole negative half.
  4. Maximum , minimum : option (D).

Trap: (A), thinking the output rides to the +15 V rail when blocks. The Zener path catches it at 5 V first. We solved the node over a full cycle with the Zener as a very steep conductance: maximum 5.00 V, minimum .

Where this shows up in industry

Op-amp stages with Zener or diode feedback are precision limiters: they protect an ADC input from overvoltage and make a clean, clamped square wave from a sine in signal conditioners.

GATE 2024 · EE · Q.61NAT · 2 marksOp-amp and wave-shaping circuits

Difference amplifier with slightly mismatched resistors: what is the CMRR in dB?

A difference amplifier is shown in the figure. Assume the op-amp to be ideal. The CMRR (in dB) of the difference amplifier is _________ (rounded off to 2 decimal places).
Difference amplifier: vin1 through 10.5 kilohm to the inverting input, 101 kilohm feedback from the output; vin2 through 9.5 kilohm to the non-inverting input, which goes to ground through 101.5 kilohm−++vin1vo+vin210.5 kΩ101 kΩ9.5 kΩ101.5 kΩ

Answer: 40.51 dB Official key: 39.50 to 41.50

  1. By superposition, with and .
  2. Write , . Then and .
  3. .

Trap: taking (without the 1/2) gives 46.53 dB, outside the key. The resistor ratios 101/10.5 and 101.5/9.5 differ by about 10 %, which is what leaks the common-mode signal. Nodal solution with an op-amp gain of gives the same 40.51 dB.

Where this shows up in industry

This is why instrumentation amplifiers for strain gauges, thermocouples and current shunts use laser-trimmed resistor networks matched to 0.01 %: with 1 % resistors a difference amplifier's CMRR falls to about 40 dB and mains hum swamps the millivolt signal.

GATE 2025 · EE · Q.17MCQ · 1 markOp-amp and wave-shaping circuits

Two ideal op-amps, one a follower inside the other's loop: what does the circuit do?

Assuming ideal op-amps, the circuit represents a
Two ideal op-amps: op-amp 1 has Vin on its non-inverting input and drives Vout; op-amp 2 has Vout on its non-inverting input and its output tied to its own inverting input; that same output also drives the inverting input of op-amp 1−+−+op-amp 1op-amp 2VoutVin
  1. (A)summing amplifier.
  2. (B)difference amplifier.
  3. (C)logarithmic amplifier.
  4. (D)buffer.

Answer: (D) Official key: D

  1. Op-amp 2 has its output tied to its own inverting input: it is a voltage follower of whatever is on its + input, which is . So its output equals .
  2. That output goes to the inverting input of op-amp 1, whose + input is . With negative feedback, op-amp 1 forces its two inputs equal: .
  3. Gain of exactly 1 with one input: a buffer, option (D).

There is only one input, so it cannot sum or subtract, and there is no diode or transistor in the loop, so nothing logarithmic. With finite gains the gain is , which tends to 1 (0.9999999 at ).

Where this shows up in industry

Putting a buffer inside the feedback loop is a standard trick for driving heavy or capacitive loads such as cables and ADC inputs: the outer op-amp keeps the accuracy while the inner stage supplies the current.

GATE 2025 · EE · Q.56NAT · 2 marksOp-amp and wave-shaping circuits

Two-op-amp differential amplifier with four 10 kΩ resistors: what is its voltage gain?

The op-amps in the following circuit are ideal. The voltage gain of the circuit is ____ (round off to the nearest integer).
Two op-amps: op-amp 1 is a non-inverting stage on the minus input terminal (10 kilohm from its inverting input to ground, 10 kilohm feedback). Its output feeds 10 kilohm into the inverting input of op-amp 2, which has 10 kilohm feedback and the plus input terminal on its non-inverting input. Vin is applied between the two non-inverting inputs−+−+Vout−+Vin10 kΩ10 kΩ10 kΩ10 kΩ

Answer: 2 Official key: 2 to 2

  1. Call the input terminals (op-amp 1) and (op-amp 2), so .
  2. Op-amp 1 is non-inverting with two equal 10 k resistors: .
  3. Op-amp 2 combines (inverting, gain ) and (non-inverting, gain ): .
  4. Voltage gain 2.

Trap: answering 1 by reading each stage as a unity follower, or 4 by multiplying the two stage gains. Checked by solving all four node equations with op-amp gain for unequal inputs: gain 2.000.

Where this shows up in industry

This two-op-amp topology is a low-cost instrumentation amplifier: both inputs see an op-amp's high input impedance, so a bridge or sensor is not loaded, and the gain is set by resistor ratios.

GATE 2026 · EE · Q.37MCQ · 2 marksOp-amp and wave-shaping circuits

Inverting amplifier 100 kΩ / 5 kΩ with open-loop gain A0 = 105: what is the closed-loop gain?

In the circuit shown, the open loop gain of the operational amplifier is .
What is the voltage gain of the circuit?
(Round off to two decimal places)
Inverting amplifier: Vin = 100 mV through 5 kilohm into the inverting input, 100 kilohm feedback, non-inverting input grounded; op-amp with open-loop gain A0 = 105, infinite input resistance and zero output resistance, supplies plus and minus 15 V−+15 V−15 V+−Vin100 mVVout5 kΩ100 kΩA0 = 105Rin = ∞ ΩRout = 0 Ω
  1. (A)–16.67
  2. (B)–20.00
  3. (C)–21.00
  4. (D)–12.67

Answer: (A) Official key: A

  1. The paper gives a deliberately low open-loop gain, (one hundred and five), so the ideal result is not accurate enough.
  2. Finite-gain formula: .
  3. : option (A).

Trap: (B) is the ideal-op-amp answer, which is what you get if you read the gain as (then ). The circuit was solved node by node with : for the 100 mV input.

Where this shows up in industry

Loop gain matters at high frequency: an op-amp with a 1 MHz gain-bandwidth has only about 100 of open-loop gain at 10 kHz, so a gain-of-20 stage there falls short exactly like this. Designers check , not just the resistor ratio.

GATE 2025 · EE · Q.39MCQ · 2 marksOp-amp and wave-shaping circuits

Large-RC low-pass network driven by a very high frequency square wave: what does the output look like?

In the circuit, shown below, if the values of R and C are very large, the form of the output voltage for a very high frequency square wave input, is best represented by
A square wave Vin between +1 V and -1 V drives a variable resistor R in series; capacitor C across the output terminals (Vout across C)1 V−1 VVinRCVout
  1. (A)Option A: triangle wave swinging the full plus 1 V to minus 1 VtVout1 V−1 V
  2. (B)Option B: square wave between plus 1 V and minus 1 VtVout1 V−1 V
  3. (C)Option C: small triangle wave centred on 0 V, far inside plus and minus 1 VtVout1 V−1 V
  4. (D)Option D: decaying spikes reaching plus and minus 1 V at each edge, as from a differentiatortVout1 V−1 V

Answer: (C) Official key: C

  1. With the output across C this is a low-pass RC network. When is much larger than the half period, the capacitor voltage hardly moves in one half cycle.
  2. Then the current is nearly constant in each half cycle, so changes linearly: up during the +1 V half, down during the −1 V half. That is a triangle wave (the network acts as an integrator).
  3. Its size is tiny: peak , far below 1 V, and centred on 0 V because the input has zero average. Option (C).

Trap: (A) has the right shape but the wrong size; a passive RC network driven by ±1 V cannot swing the full ±1 V at high frequency. (D) is what you see across R (a differentiator). We time-stepped one period from the periodic steady state with half periods: peak 0.5 mV, straight to within 0.1 %.

Where this shows up in industry

This is the RC filter after a PWM output: a microcontroller's PWM pin through an RC low-pass gives a DC level with a small triangular ripple, the cheapest digital-to-analog converter there is, and the same sizing rule (RC much longer than the PWM period) sets the ripple.

From GATE prep to a electronics hardware career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.