GATE Electrical: AC circuits (phasors, power factor, three-phase loads, wattmeters, two-port networks, coupled coils), previous-year questions solved

Every AC-circuit question from the last five GATE Electrical papers that is not on another page: an AC Thevenin equivalent with a controlled source, true power factor with a harmonic, half-cycle average power, neutral shift in an unbalanced star, mixed delta and star loads, a capacitive load behind line inductance, two wattmeters on an unbalanced load, cascaded and paralleled two-ports, reflected impedance of coupled coils and maximum power transfer. Each answer matches the official key and was recomputed by a full circuit solve.

Questions from official GATE EE papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 16 Nov 2026 · 11 questions

GATE 2023 · EE · Q.51NAT · 2 marksAC steady state, power and power factor

Dependent source 4i_x and i = sin 1000t: what is the Thevenin voltage across a-b at t = 5 ms?

For the circuit shown, if , the instantaneous value of the Thevenin's equivalent voltage (in Volts) across the terminals a-b at time is __________ (Round off to 2 decimal places).
Terminal a: 10 ohm in series with minus j10 ohm down to terminal b carrying i x; dependent voltage source 4 i x (plus at a) to a node with 10 ohm plus j10 ohm down to b and a current source i = sin 1000 t from b up into that nodeab+−4ix10 Ωix−j10 Ω10 Ωj10 Ωi = sin 1000t

Answer: Official key: -12.1 to -11.9

  1. Work in phasors with the sine as reference: . Call the left branch and the middle branch ; let be the node right of the controlled source.
  2. With a-b open, all of flows down : , so .
  3. The controlled source sets , so .
  4. KCL at : the source current splits into and the controlled-source branch (which carries on to node a): , so .
  5. . It is purely real, so .
  6. At : rad and .

Trap: taking in degrees gives V. The argument is in radians. A full nodal solve of the two unknown node voltages gives the same .

Where this shows up in industry

Every AC small-signal model of an amplifier or a grid-tied inverter's control loop is a network with controlled sources like this one, and circuit simulators (SPICE AC analysis) do exactly this complex nodal solve to report Thevenin and Norton equivalents at a port.

GATE 2026 · EE · Q.26MCQ · 1 markAC steady state, power and power factor

A 325 V sine source drives 12 A fundamental plus 9 A third harmonic: what is the load power factor?

A single-phase voltage source V delivers a current, A to a load.
The load power factor, correct up to two decimal places, is:
  1. (A)1.00
  2. (B)0.80
  3. (C)0.65
  4. (D)0.57

Answer: (B) 0.80 Official key: B

  1. Only the current component at the voltage's frequency carries average power: (the 150 Hz term averages to zero against a 50 Hz voltage).
  2. , .
  3. . Answer (B).

Trap: the fundamental current is in phase with the voltage, so the displacement factor is 1 and option (A) looks right. The third harmonic adds rms current without adding power, and the true power factor is displacement factor × distortion factor . Averaging over one period numerically gives 0.8000.

Where this shows up in industry

Rectifier loads (SMPS, LED drivers, VFD front ends) draw exactly this kind of current. Power analysers report true PF and displacement PF separately, and harmonic standards such as IEC 61000-3-2 and IEEE 519 exist because harmonic current heats cables and transformers without delivering power.

GATE 2026 · EE · Q.42MCQ · 2 marksAC steady state, power and power factor

v = Vm sin ωt and i = Im sin(ωt − θ): what is the average power over a half cycle?

An electrical component has voltage drop , when the current through it is .
What is the average power dissipated over a half cycle corresponding to ?
  1. (A)0
  2. (B)
  3. (C)
  4. (D)

Answer: (C) Official key: C

  1. .
  2. The second term oscillates at , so one half cycle of the source () is exactly one full period of it, and it averages to zero.
  3. Average over the half cycle , the same as over a full cycle. Answer (C).

Trap: picking (A) because and each average to zero over a cycle. Power is their product, and the product does not average to zero. Picking (B) forgets the factor from . We averaged numerically over for five random sets of : only (C) matches every time.

Where this shows up in industry

Digital power meters and power analysers compute real power by averaging sampled over a whole number of half cycles, which is why they lock their averaging window to zero crossings: any whole number of half cycles gives the true average power.

GATE 2022 · EE · Q.21MCQ · 1 markThree-phase circuits and wattmeters

Unbalanced star load with Z_A = 10 Ω and Z_B = 20∠60° Ω: which Z_C makes the voltage between n and n' zero?

In the circuit shown below, a three-phase star-connected unbalanced load is connected to a balanced three-phase supply of with phase sequence . The star connected load has and . The value of in , for which the voltage difference across the nodes and is zero, is
Star-connected source E A, E B, E C with star point n feeding a star-connected load Z A, Z B, Z C with star point n prime; the two star points are not connected+EA+EB+ECZAZBZCnn′
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (C) Official key: C

  1. Phase voltages: , , V (line voltage ).
  2. Millman: . It is zero when the numerator is zero.
  3. and , so must be .
  4. . Answer (C).

Trap: assuming the load must be balanced, or copying 's angle (D, which leaves a 50 V neutral shift). Zero shift needs the three phase currents to add to zero, not equal impedances. A nodal solve at for each option confirms only (C) gives 0 V.

Where this shows up in industry

In LV distribution a lost neutral turns every unbalanced building into this circuit: the star point drifts and lightly loaded phases see overvoltage that burns appliances. Utilities balance single-phase loads across phases and use neutral-loss protection for this reason.

GATE 2022 · EE · Q.34NAT · 1 markThree-phase circuits and wattmeters

Delta of Z1 = 18 + j24 Ω and star of Z2 = 6 + j8 Ω on a 100√3 V supply: what does the line ammeter read?

Two balanced three-phase loads, as shown in the figure, are connected to a V, three-phase, 50 Hz main supply. Given and . The ammeter reading, in amperes, is _______. (round off to nearest integer)
Lines R, Y, B with 100 root 3 volts between R and Y and an ammeter A in line R; three Z1 impedances form a delta across the lines and three Z2 impedances form a star with a floating centreAZ1RYB100√3 VZ1Z1Z2Z2Z2

Answer: Official key: 20 to 20

  1. Read the figure: the three connect line to line (a delta), the three meet at a floating star point.
  2. Convert the delta to a star: per phase, the same as .
  3. Per phase the two star loads are in parallel: , .
  4. Phase voltage , so the line current is .

Trap: putting the line voltage across the star impedance, or forgetting the delta-to-star factor of 3 (treating as a star gives 13 A). A nodal solve of the full circuit, with the star point as the only unknown node, gives 20.00 A in line R.

Where this shows up in industry

Plant feeders carry delta-connected motors alongside star-connected heaters and lighting, and engineers reduce everything to per-phase star equivalents exactly this way to size cables, breakers and the transformer.

GATE 2023 · EE · Q.64NAT · 2 marksThree-phase circuits and wattmeters

Delta R-C load fed through 31.83 mH lines from 415 V: what is the load voltage V_AB?

A balanced delta connected load consisting of the series connection of one resistor () and a capacitor () in each phase is connected to three-phase, 50 Hz, 415 V supply terminals through a line having an inductance of per phase, as shown in the figure. Considering the change in the supply terminal voltage with loading to be negligible, the magnitude of the voltage across the terminals in Volts is _____________ (Round off to the nearest integer).
3-phase 50 Hz 415 V supply terminals feed nodes A, B, C through a line inductance L each; a delta of three R plus C branches connects A to B, B to C and C to ALARCLBRCLCRC3-phase,50 Hz,415 V(r.m.s.)supplyterminalsR = 15 Ω, L = 31.83 mH, C = 212.21 μF

Answer: Official key: 414 to 416

  1. Reactances at 50 Hz: , .
  2. Delta branch ; star equivalent per phase.
  3. Per phase: , , .
  4. Load phase voltage , so .

Trap: assuming the line inductance must drop the voltage. With a capacitive load the drop across and the load voltage are out of phase, and here , so the load sees the full supply voltage. A three-node solve of the full circuit with the printed (rounded) L and C gives 415.01 V.

Where this shows up in industry

This is why a capacitive load (or a power-factor-correction bank) at the end of an inductive feeder lifts the receiving-end voltage: utilities check this voltage rise before switching capacitor banks, and too much compensation on a light load gives overvoltage.

GATE 2024 · EE · Q.50NAT · 2 marksThree-phase circuits and wattmeters

Two wattmeters with Z1 = 50∠−90° Ω and Z2 = 200∠−30° Ω on 400 V: what is |W1 − W2|?

In the circuit shown, and . It is supplied by a three phase 400 V source with the phase sequence being R-Y-B. Assume the watt meters and to be ideal. The magnitude of the difference between the readings of and in watts is ___________ (rounded off to 2 decimal places).
Two-wattmeter connection: W1 current coil in line R with its pressure coil from R (plus) to B (minus); W2 current coil in line Y with its pressure coil from the Y-side load node (plus) to line B (minus); Z1 is connected between line R and line B, Z2 between line R and line YRBY+−cc+−pcW1Z1Z2−+pc+−ccW2

Answer: Official key: 692 to 693

  1. Read the figure: is across lines R and B, across R and Y; nothing but 's pressure coil sits between B and Y. Take , , (R-Y-B).
  2. A, A, so A and .
  3. .
  4. , which is all of the power in (); is a pure capacitor.

Trap: using the balanced-load rule . This load is unbalanced (two impedances only), so compute each meter from its own voltage and current. Check: W equals the total load power.

Where this shows up in industry

Three-wire three-phase energy meters are two-element meters built on this two-wattmeter (Blondel) principle, and with unbalanced or very low-power-factor loads one element can legitimately read zero or negative, which commissioning engineers must not mistake for a wiring fault.

GATE 2024 · EE · Q.48NAT · 2 marksTwo-port networks and coupled inductors

Network P (given Z matrix) cascaded with network Q (given Y matrix): what is β, the B parameter of the combined ABCD matrix?

Two passive two-port networks P and Q are connected as shown in the figure. The impedance matrix of network P is . The admittance matrix of network Q is . Let the ABCD matrix of the two-port network R in the figure be . The value of in is _____________ (rounded off to 2 decimal places).
Two-port network P in cascade with two-port network Q; together they form two-port network RTwo-portnetworkPTwo-portnetworkQTwo-port network R

Answer: Official key: -19.90 to -19.70

  1. Cascaded networks multiply their ABCD matrices in order: , so .
  2. From : , .
  3. From : , .

Trap: multiplying in the wrong order ( gives ) or swapping and (P is not reciprocal). We also shorted port 2 of R, pushed 1 A out of it and walked back through Q's Y equations and P's Z equations: the source needs V, which is by definition.

Where this shows up in industry

Transmission lines, filters and RF chains are modelled as cascades of ABCD (transmission) matrices: a long power line is a chain of nominal-π sections, and multiplying their matrices gives the sending-end voltage and current for a given load.

GATE 2023 · EE · Q.52NAT · 2 marksTwo-port networks and coupled inductors

Two-port with y11 = 5 S, y22 = 1 S, y12 = y21 = −2.5 S, a 3 Ω bridge and a 6 Ω load: how much power reaches R_L?

The admittance parameters of the passive resistive two-port network shown in the figure are

The power delivered to the load resistor in Watt is __________ (Round off to 2 decimal places).
20 V battery across port 1 (terminals 1 and common 1 prime 2 prime) of a resistive two-port network, a 3 ohm resistor from terminal 1 to terminal 2, and R L = 6 ohm across port 220 VResistiveTwo-portNetwork12RL =6 Ω1′, 2′3 Ω

Answer: Official key: 237 to 239

  1. The 3 Ω resistor sits between terminals 1 and 2, in parallel with the network. Two-ports in parallel add their Y matrices; the 3 Ω adds to and and to and : S, S.
  2. Port 2 into the load: .
  3. .

Trap: forgetting the 3 Ω bridge (306 W). Note: these numbers are not those of a real passive resistive network. Its π-equivalent has a shunt of S at port 2, which is why the load voltage (37.78 V) exceeds the 20 V source. Use the parameters as given, as the official key does.

Where this shows up in industry

Y-parameters are what a network analyser measures on transistors and RF blocks, and adding Y matrices is how designers fold feedback elements (like this bridging resistor) into an amplifier model before predicting its gain and output power.

GATE 2024 · EE · Q.49NAT · 2 marksTwo-port networks and coupled inductors

Coupled coils of 125 mH and 1 mH with M = 5 mH and a 50 μF secondary at 5000 rad/s: what is Z_th at P-Q?

For the circuit shown in the figure, the source frequency is . The mutual inductance between the magnetically coupled inductors is with their self inductances being and . The Thevenin's impedance, , between the terminals P and Q in is _________ (rounded off to 2 decimal places).
Source with internal impedance Z s connected to terminals P and Q; from P a 4 ohm series resistor, a 4 ohm shunt resistor, then 2 ohm in series with a 125 mH coil to the return line; the 125 mH coil is coupled (5 mH mutual, dots at the top of both coils) to a 1 mH coil closed by a 50 microfarad capacitor; Z th is seen looking into P and QSourceZsPQ4 Ω4 Ω2 Ω125 mH1 mH50 μF5 mHZth

Answer: Official key: 5.32 to 5.34

  1. Reactances at : , , , .
  2. Secondary loop impedance: .
  3. Reflected into the primary: . It cancels the primary's , so the 2 Ω + 125 mH branch looks like a plain 2 Ω.
  4. (looking from P-Q into the network, so is not part of it).

Trap: worrying about the dots. The reflected impedance depends on , so the dot orientation does not change it; a three-mesh solve with and with gives the same .

Where this shows up in industry

Reflected impedance is how wireless chargers and resonant converters work: the receiver coil is tuned with a capacitor so that what the transmitter sees is mostly resistive, and the same calculation tells a protection engineer how a CT's secondary burden appears in the primary circuit.

GATE 2026 · EE · Q.60NAT · 2 marksTwo-port networks and coupled inductors

10 V source with a 5 Ω, 10 Ω and 4 Ω two-port: which R_L receives maximum power?

Consider the two-port network shown. For maximum power transfer to the resistive load (), the value of should be__________
(Round off to two decimal places)
10 V source at port 1 (v1, i1); inside the two-port a 5 ohm shunt at port 1, a 10 ohm series resistor and a 4 ohm shunt at port 2; load R L across port 2 (v2, i2)+−10 Vi1+v1−5 Ω10 Ω4 Ωi2+v2−RL

Answer: Official key: 2.81 to 2.91

  1. Maximum power goes to a resistive load when seen from port 2.
  2. Kill the ideal 10 V source (short it). The 5 Ω resistor is directly across that source, so it is shorted and drops out.
  3. From port 2: 4 Ω in parallel with 10 Ω (to the shorted port 1): .

Trap: keeping the 5 Ω in series with the 10 Ω, giving . Anything directly across an ideal voltage source never affects the rest of the circuit. A 1 A test-current solve at port 2 with the source killed reads 2.857 V.

Where this shows up in industry

Matching a load to the source resistance matters for antennas, RF stages and sensor interfaces, where signal power is scarce. Power systems deliberately do the opposite: matching would waste half the power, so generators and grids run with load impedances far above the source impedance.

From GATE prep to a power systems career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.