GATE Electronics (EC): Electronic Devices (energy bands, carrier concentration, drift and diffusion, P-N junction, BJT, MOS capacitor, MOSFET, LED and solar cell), previous-year questions solved

Every electronic devices question from the last five GATE Electronics and Communication papers, solved: Fermi level and carrier concentration, drift and diffusion, P-N junction, Zener and BJT, the MOS capacitor and MOSFET, and LED and solar-cell numbers. Each answer matches the official key and was recomputed by code from the device equations with the constants printed in the paper.

Questions from official GATE EC papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 17 Nov 2026 · 15 of 30 questions on this page

GATE 2022 · EC · Q.17MCQ · 1 markEnergy bands, carrier concentration and Fermi level

n = 1e16 cm^-3 gives E_C - E_Fn = 200 meV, kT = 26 meV: E_C - E_Fn when n = 0.5e16 cm^-3?

In a non-degenerate bulk semiconductor with electron density , the value of , where and denote the bottom of the conduction band energy and electron Fermi level energy, respectively. Assume thermal voltage as and the intrinsic carrier concentration is . For , the closest approximation of the value of , among the given options, is __________.
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (C) Official key: C

  1. Non-degenerate means Boltzmann statistics: .
  2. Take the ratio of the two cases, cancels: .
  3. So .
  4. , so : option (C).
  5. Fewer electrons means the Fermi level sits lower, further below , so the gap grows. The given is not needed because .

Trap: moving the Fermi level the wrong way, , option (D). Options (A) and (B) are , a whole instead of . We computed all three and checked that only matches an option.

Where this shows up in industry

Doping control in a fab is checked through the Fermi level: a factor of two in doping moves it by only kT ln 2, about 18 meV at room temperature. That is why threshold voltage and junction built-in voltage shift only a little for a small change in dose.

GATE 2022 · EC · Q.47MSQ · 2 marksEnergy bands, carrier concentration and Fermi level

Which statements about semiconductor devices are correct (intrinsic density, BJT doping, current, mobility)?

Select the CORRECT statement(s) regarding semiconductor devices.
  1. (A)Electrons and holes are of equal density in an intrinsic semiconductor at equilibrium.
  2. (B)Collector region is generally more heavily doped than Base region in a BJT.
  3. (C)Total current is spatially constant in a two terminal electronic device in dark under steady state condition.
  4. (D)Mobility of electrons always increases with temperature in Silicon beyond 300 K.

Answer: (A) and (C) Official key: A,C

  1. (A) is true. Every electron in an intrinsic crystal comes from a broken bond that also leaves a hole, so .
  2. (B) is false. A BJT has a heavily doped emitter, a base doped lighter than the emitter, and a collector doped lightest (typically about , and ). The light collector doping lets the collector-base depletion region reach into the collector and gives a high breakdown voltage, so the collector is not more heavily doped than the base.
  3. (C) is true. In steady state the electron and hole continuity equations add up to : recombination and generation only move current between the electron and hole parts. The total current is the same at every point.
  4. (D) is false. Above 300 K lattice (phonon) scattering dominates and mobility falls, roughly as for electrons in silicon. So it does not always increase.
  5. Correct options: (A) and (C).

Trap: (D). Mobility does rise with temperature at low temperature, where ionized-impurity scattering dominates, so \"increases\" looks plausible. Beyond 300 K in lightly or moderately doped silicon it falls. Our model gave 1037, 630 and 259 at 300, 400 and 600 K. We also checked (A), (B) and (C) with small models: for an intrinsic sample, a typical doping set, and conserved for an arbitrary generation and recombination profile.

Where this shows up in industry

The emitter-base-collector doping order is why a BJT has current gain and a usable Early voltage, and falling mobility with temperature is why a MOSFET drive current drops on a hot chip, a corner every timing sign-off includes.

GATE 2023 · EC · Q.16MCQ · 1 markEnergy bands, carrier concentration and Fermi level

If the Fermi level lies in the conduction band, what is the semiconductor called?

In a semiconductor, if the Fermi energy level lies in the conduction band, then the semiconductor is known as
  1. (A)degenerate n-type.
  2. (B)degenerate p-type.
  3. (C)non-degenerate n-type.
  4. (D)non-degenerate p-type.

Answer: (A) Official key: A

  1. The Fermi level marks where the occupation probability is . A Fermi level in the conduction band, above the intrinsic level, means a lot of electrons: the semiconductor is n-type. (A p-type one has below mid-gap.)
  2. Boltzmann statistics, , hold only when is a few below . Once is inside the band the electron gas follows Fermi-Dirac statistics. This is called degenerate.
  3. Degenerate n-type: option (A).

Trap: picking (C) because \"n-type\" is right and \"non-degenerate\" sounds like the normal case. A non-degenerate sample has in the gap, below . We checked it with the Fermi-Dirac integral: with 0.1 eV inside the band, Boltzmann statistics overestimate by a factor 7.69, while 0.2 eV below they agree within 1%.

Where this shows up in industry

Source and drain regions of a MOSFET, and the heavily doped emitter of a BJT, are doped degenerately so that they behave like metals and give low-resistance contacts. Device simulators switch from Boltzmann to Fermi-Dirac statistics for exactly these regions.

GATE 2023 · EC · Q.17MCQ · 1 markEnergy bands, carrier concentration and Fermi level

Which statement is true for an intrinsic semiconductor at T = 0 K (band occupancy)?

For an intrinsic semiconductor at temperature , which of the following statement is true?
  1. (A)All energy states in the valence band are filled with electrons and all energy states in the conduction band are empty of electrons.
  2. (B)All energy states in the valence band are empty of electrons and all energy states in the conduction band are filled with electrons.
  3. (C)All energy states in the valence and conduction band are filled with holes.
  4. (D)All energy states in the valence and conduction band are filled with electrons.

Answer: (A) Official key: A

  1. At the Fermi function is a step: for and for . In an intrinsic semiconductor lies near the middle of the gap.
  2. So every state below (the whole valence band) is full of electrons, and every state above it (the whole conduction band) is empty. There is no thermal energy to lift an electron across the gap, so there are no free electrons and no holes.
  3. That is option (A). The crystal is a perfect insulator at 0 K.

Trap: (D) or (B). Electrons cannot fill both bands, nor sit only in the conduction band, because they fill the lowest states first. (C) mixes terms: a hole is an empty electron state, not something that fills a band. We evaluated the Fermi function with of 0.1 meV on every state of both bands: the valence band was full and the conduction band empty, which matches only (A).

Where this shows up in industry

This is why cooled detectors have so little dark current: thermally generated electron-hole pairs fall roughly as exponentially with temperature, so cooling an infrared photodiode far below room temperature removes most of its dark noise.

GATE 2023 · EC · Q.61NAT · 2 marksEnergy bands, carrier concentration and Fermi level

E_F is 0.35 eV above E_V, N_V = 1e19 cm^-3 at 300 K: hole concentration of silicon at 400 K?

In a semiconductor device, the Fermi-energy level is above the valence band energy. The effective density of states in the valence band at is . The thermal equilibrium hole concentration in silicon at is ____________ (rounded off to two decimal places). Given at is .

Answer: Official key: 60.00 to 70.00

  1. For a non-degenerate semiconductor, .
  2. Both and change with temperature. , so .
  3. .
  4. .
  5. This takes to be unchanged at 400 K, as the question states, and ignores the small shrinkage of the band gap.

Trap: keeping at its 300 K value gives . Keeping gives . Both are outside the official range 60 to 70. We evaluated all three variants: only scaling both and lands in range.

Where this shows up in industry

Carrier density rising exponentially with temperature is the reason leakage current and thermal runaway are checked at the hot corner in chip design, and why power devices carry a maximum junction temperature.

GATE 2024 · EC · Q.22MCQ · 1 markEnergy bands, carrier concentration and Fermi level

Which plot shows free electron concentration against temperature for n-type silicon?

For non-degenerately doped n-type silicon, which one of the following plots represents the temperature () dependence of free electron concentration ()?
  1. (A)Plot A: log of electron concentration against 1/T. It starts high at the left, falls steeply to a flat plateau, stays flat over a wide range and then falls again toward the right endlog(n)(cm−3)1/T (K−1)
  2. (B)Plot B: log of electron concentration against 1/T is a horizontal straight linelog(n)(cm−3)1/T (K−1)
  3. (C)Plot C: log of electron concentration against 1/T is flat from the left, then falls toward the right endlog(n)(cm−3)1/T (K−1)
  4. (D)Plot D: log of electron concentration against 1/T is a straight line falling from the left to the rightlog(n)(cm−3)1/T (K−1)

Answer: (A) Official key: A

  1. Charge neutrality for n-type silicon is . The temperature changes which term does the work.
  2. At low temperature (large ) the donors are not yet ionised. Freeze-out: falls as falls, roughly as , so drops on the right of the plot.
  3. Over a wide middle range the donors are all ionised and thermal generation across the gap is still negligible, so . is flat. For our model gives this plateau between about 106 K and 510 K.
  4. At high temperature (small ) intrinsic carriers exceed and rises steeply again, so shoots up on the left of the plot. In the model this starts near 580 K.
  5. The curve is therefore: steep fall on the left, flat plateau, fall on the right: plot (A).

Trap: picking (C), the textbook picture that stops at the plateau. It misses the intrinsic rise at high temperature. (D) is a single straight exponential, which is what a pure intrinsic semiconductor gives, and (B) says never changes with . The code solved charge neutrality over 40 K to 900 K and compared the shape of the result with each printed curve: only (A) has the pattern fall, flat, fall.

Where this shows up in industry

This is why a silicon chip works over its rated temperature range: the dopant sets the carrier density on the plateau, and the intrinsic rise at high temperature is what limits ordinary silicon devices to about 150 C. Power and high-temperature electronics use wider-gap materials such as silicon carbide so that the plateau extends further.

GATE 2024 · EC · Q.63NAT · 2 marksEnergy bands, carrier concentration and Fermi level

n-type with 5% neutral donors, E_F 0.25 eV below E_C, degeneracy 2: find E_C minus E_D

A non-degenerate n-type semiconductor has 5 % neutral dopant atoms. Its Fermi level is located at 0.25 eV below the conduction band () and the donor energy level () has a degeneracy of 2. Assuming the thermal voltage to be 20 mV, the difference between and (in eV, rounded off to two decimal places) is _________.

Answer: Official key: 0.17 to 0.19

  1. The fraction of donors that still hold their electron (neutral) is , with degeneracy .
  2. Set it to 0.05: , so .
  3. . The donor level lies above .
  4. , so .
  5. .

Trap: putting the degeneracy factor on the wrong side, or reading 5% as the ionised fraction. Moving the factor 2 to the other side gives 0.20 eV and using 95% neutral gives 0.30 eV, both outside the key. Taking gives 0.191 eV, which only just rounds into the key range. The code solved the occupancy equation and substituted the answer back to recover 5%.

Where this shows up in industry

Dopant ionisation energy decides how much of the dopant is active at room and low temperature. Process engineers check it when they work with deep dopants or cryogenic operation, where incomplete ionisation changes the sheet resistance and the threshold voltage.

GATE 2025 · EC · Q.31MSQ · 1 markEnergy bands, carrier concentration and Fermi level

Which elements can be used as n-type dopants for silicon?

Which of the following can be used as an n-type dopant for silicon? Select the correct option(s).
  1. (A)Arsenic
  2. (B)Boron
  3. (C)Gallium
  4. (D)Phosphorous

Answer: (A) and (D) Official key: A;D

  1. Silicon is in group IV of the periodic table: four valence electrons, all used in bonds.
  2. An n-type dopant is a donor. It must have five valence electrons, so that four make bonds and the fifth is free to move. That is a group V element.
  3. Arsenic and phosphorus are group V: donors. Boron and gallium are group III, with three valence electrons: they leave a missing bond, a hole, and are p-type acceptors.
  4. Correct options: (A) and (D).

Trap: marking boron or gallium because they are the common dopants in textbooks. They are common, but for p-type. The code counted valence electrons from the group number: arsenic and phosphorus gave 5, boron and gallium gave 3.

Where this shows up in industry

Phosphorus and arsenic are the n-type dopants in CMOS: arsenic for shallow, abrupt source/drain extensions because it diffuses slowly, and phosphorus for deeper junctions and n-wells. Boron is the standard p-type dopant.

GATE 2022 · EC · Q.16MCQ · 1 markCarrier transport: drift, diffusion, generation and recombination

p-type bar lit at x = 0 (excess n = 1e14 cm^-3), L_n = 2 um: steady-state electron density at x = 2 um?

Consider a long rectangular bar of direct bandgap -type semiconductor. The equilibrium hole density is and the intrinsic carrier concentration is . Electron and hole diffusion lengths are and , respectively. The left side of the bar () is uniformly illuminated with a laser having photon energy greater than the bandgap of the semiconductor. Excess electron-hole pairs are generated ONLY at because of the laser. The steady state electron density at is due to laser illumination. Under these conditions and ignoring electric field, the closest approximation (among the given options) of the steady state electron density at , is ___________ .
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. In a -type bar the electrons are the minority carriers. With no field, the extra electrons only diffuse and recombine. Steady state continuity: , which means .
  2. For a long bar the solution that dies away is . The relevant length is the electron diffusion length, . The hole length of is not used.
  3. The equilibrium electron density is , negligible next to .
  4. At : : option (A).

Trap: using the hole diffusion length, , which is not an option (the nearest is (B)). Option (D), , is only the equilibrium electron density. We solved the diffusion equation on a grid with and got at .

Where this shows up in industry

The minority-carrier diffusion length sets how far photo-generated carriers travel before they recombine, so it fixes the thickness a solar cell or photodiode absorber can usefully have. Lifetime and diffusion length are routinely measured on wafers with a laser or light pulse.

GATE 2022 · EC · Q.56NAT · 2 marksCarrier transport: drift, diffusion, generation and recombination

p-type bar under illumination, l_n = 1e-4 cm, G and R profiles given: electron current density at x = 2 l_n?

A -type semiconductor with zero electric field is under illumination (low level injection) in steady state condition. Excess minority carrier density is zero at , where is the diffusion length of electrons. Assume electronic charge, . The profiles of photo-generation rate of carriers and the recombination rate of excess minority carriers () are shown. Under these conditions, the magnitude of the current density due to the photo-generated electrons at is _________ (rounded off to two decimal places).
Photo-generation rate and recombination rate against position x for a bar from minus 2 l_n to plus 2 l_n. Generation is 10 to the 20 per cubic centimetre per second for x between minus l_n and plus l_n and zero outside. Recombination of excess carriers is 10 to the 20 times exp of minus the magnitude of x over l_n between minus l_n and plus l_n, peaking at x = 0, and zero outsideSemiconductor10200Photo generationRate (cm−3/s)−2ln−ln0ln2lnx10200R = 1020 exp(−|x|/ln)Excess minoritycarrier recombinationrate (cm−3/s)−2ln−ln0ln2lnx

Answer: Official key: 0.57 to 0.61

  1. With zero field the electrons move only by diffusion. In steady state the electron flux (electrons per cm per second) obeys continuity: .
  2. The structure is symmetric about , so the flux there is zero, . Then .
  3. Generation: for , zero beyond, so .
  4. Recombination (from the plot, only for ): .
  5. .
  6. .

Trap: forgetting recombination and using generation alone gives . Carrying all the way to , instead of stopping at as the plot shows, gives . Both fall outside the official range 0.57 to 0.61. We integrated numerically over the plotted profiles and got 0.589.

Where this shows up in industry

Photodiode and solar-cell models start from this generation-minus-recombination balance. The collected photocurrent is the charge that is generated within a diffusion length of the junction and does not recombine on the way.

GATE 2023 · EC · Q.56NAT · 2 marksCarrier transport: drift, diffusion, generation and recombination

Extrinsic semiconductor, p = 1.5 n_i: mu_n/mu_p for equal electron and hole drift current?

In an extrinsic semiconductor, the hole concentration is given to be where is the intrinsic carrier concentration of . The ratio of electron to hole mobility for equal hole and electron drift current is given as __________ (rounded off to two decimal places).

Answer: Official key: 2.20 to 2.30

  1. Mass action: . With , the electron density is .
  2. Drift current density from each carrier in the same field : and .
  3. Equal currents: , so .

Trap: using (forgetting that is not ), or inverting the ratio, . Both are outside the official range 2.20 to 2.30. We computed from and checked that holds for .

Where this shows up in industry

Electron mobility in silicon is about three times the hole mobility, which is why a pMOS in a standard cell is drawn wider than the nMOS to give a matched drive current. The resistivity of a doped wafer comes from the same sum of an electron term and a hole term.

GATE 2024 · EC · Q.26MSQ · 1 markCarrier transport: drift, diffusion, generation and recombination

Peaked electron concentration at equilibrium: which diffusion, drift and field directions are true?

The free electron concentration profile in a doped semiconductor at equilibrium is shown in the figure, where the points A, B, and C mark three different positions. Which of the following statements is/are true?
Electron concentration n against x for a doped semiconductor at equilibrium. The curve exists only between points A and C on the x axis. It starts at a moderate value at A, rises smoothly to a maximum at B, and falls back to the same value at Cn(x)(x)ABC
  1. (A)For between B and C, the electron diffusion current is directed from C to B.
  2. (B)For between B and A, the electron drift current is directed from B to A.
  3. (C)For between B and C, the electric field is directed from B to C.
  4. (D)For between B and A, the electric field is directed from A to B.

Answer: (A) and (B) and (C) Official key: A;B;C

  1. Electrons diffuse from high to low concentration. Between B and C the concentration falls, so electrons move from B toward C. Electrons are negative, so the diffusion current is the other way: from C to B. Statement (A) is true.
  2. At equilibrium the net electron current is zero, so the drift current exactly cancels the diffusion current: , which gives .
  3. Between B and A the concentration rises toward B, so the diffusion current points from A to B. The drift current is opposite: from B to A. Statement (B) is true.
  4. Between B and C, , so : the field points from B to C. Statement (C) is true.
  5. Between B and A, , so : the field points from B to A, not from A to B. Statement (D) is false.
  6. Correct options: (A), (B) and (C).

Trap: marking (D) by reading the electron drift current and the field as the same direction. Electrons drift against the field, so the field points the opposite way to their motion's current. We built with a peak, solved for from zero net current, checked that drift plus diffusion is zero at 38 points and that the field is positive on the C side and negative on the A side.

Where this shows up in industry

A built-in field produced by a doping gradient, with drift balancing diffusion at equilibrium, is the idea behind graded-base bipolar transistors. The field in the base sweeps carriers across faster and raises the speed of high-frequency BJTs.

GATE 2025 · EC · Q.46MCQ · 2 marksCarrier transport: drift, diffusion, generation and recombination

Intrinsic resistivity with ni = 2.5e16 per m^3, mobilities 0.15 and 0.05 m^2/Vs at 300 K

The intrinsic carrier concentration of a semiconductor is at 300 K. If the electron and hole mobilities are and , respectively, then the intrinsic resistivity of the semiconductor (in ) at 300 K is ________. (Charge of an electron .)
  1. (A)1.65
  2. (B)1.25
  3. (C)0.85
  4. (D)1.95

Answer: (B) Official key: B

  1. In an intrinsic semiconductor , and both carriers conduct: .
  2. .
  3. .
  4. Option (B).

Trap: counting only the electrons, because they are the faster carrier. That gives 1.67 kΩ.m, which sits next to option (A) 1.65. Holes carry current as well, and in an intrinsic crystal there are as many holes as electrons. The code computed the electron-only value and confirmed the nearest option to it is (A), not the key.

Where this shows up in industry

Intrinsic silicon at 300 K has a resistivity of about 2.3e5 ohm.cm. High-resistivity silicon substrates for RF chips are grown with as little doping as possible to approach that value, because a more resistive substrate wastes less signal power.

GATE 2025 · EC · Q.48MCQ · 2 marksCarrier transport: drift, diffusion, generation and recombination

Electron diffusivity of germanium at 300 K from a mobility of 0.38 m^2/Vs

The electron mobility in a non-degenerate germanium semiconductor at 300 K is . The electron diffusivity at 300 K (in , rounded off to the nearest integer) is _______. (Consider the Boltzmann constant and the charge of an electron .)
  1. (A)26
  2. (B)98
  3. (C)38
  4. (D)10

Answer: (B) Official key: B

  1. Einstein relation for a non-degenerate semiconductor: .
  2. .
  3. .
  4. Convert to : , so , which is 98: option (B).

Trap: leaving the answer in or converting the wrong way. The product is , and only the factor gives the figure the question asks for. Options (A) 26 and (C) 38 are just the thermal voltage in mV and the mobility digits. The code computed from the Einstein relation and confirmed that rounding gives 98 and not 26, 38 or 10.

Where this shows up in industry

The Einstein relation links the two numbers a device simulator needs for carrier transport. TCAD tools take the mobility from measured or modelled data and derive the diffusion constant from it, rather than storing both.

GATE 2026 · EC · Q.64NAT · 2 marksCarrier transport: drift, diffusion, generation and recombination

Electrons fall from 2e17 to 1e16 cm^-3 between x = 1 um and 4 um: electron diffusion current density in A/mm2

Consider that the concentration of electrons in a semiconductor bar varies linearly from at to at along the x-direction. Assume that the concentration of electrons is not varying along other directions (that is along y- and z-directions).
[Given: the mobility of electron is , thermal voltage is and electronic charge is Coulomb.]
The density of electron diffusion current (in A/mm) is __.
(rounded off to two decimal places)

Answer: Official key: -36.50 to -34.50 OR 34.50 to 36.50

  1. Diffusion constant from the Einstein relation: .
  2. Concentration gradient: .
  3. Electron diffusion current density: .
  4. Convert, since : . The minus sign means the current points toward smaller : electrons diffuse toward (down the gradient), and their current is opposite. The official key accepts the magnitude with either sign.

Trap: dividing by instead of the between the two points, which gives about . Also, forgetting the cm to mm conversion leaves . We computed both wrong paths and confirmed that neither lies in the key range.

Where this shows up in industry

Diffusion current from a carrier gradient is what carries the collector current in a BJT base and the current in a forward-biased diode, so process engineers tune base width and doping profiles to set the gradient. Device simulators solve this same drift-diffusion equation on a mesh.

From GATE prep to a core electronics or embedded career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.