GATE Electronics (EC): Analog Circuits (diode clippers, clampers and rectifiers, BJT and MOSFET amplifiers, current mirrors, differential pairs, op-amps, filters and oscillators), previous-year questions solved

Every analog circuits question from the last five GATE Electronics and Communication papers, solved: diode clippers, clampers, rectifiers and Zener regulators, BJT and MOSFET bias and small-signal gain, current mirrors and differential pairs, and op-amp amplifiers, filters, Schmitt triggers and oscillators. Each answer matches the official key and was recomputed by code from a numeric model of the circuit, with every diode and transistor region checked.

Questions from official GATE EC papers (IIT Kharagpur 2022, IIT Kanpur 2023, IISc Bengaluru 2024, IIT Roorkee 2025, IIT Guwahati 2026); solutions by Skill-Lync. · Updated 17 Nov 2026 · 7 of 32 questions on this page

GATE 2022 · EC · Q.57NAT · 2 marksDiode circuits: clippers, clampers, rectifiers and Zener regulators

2 kOhm divider with a 0.7 V diode across the middle resistor: min over max of small-signal gain dVout/dVin?

A circuit and the characteristics of the diode (D) in it are shown. The ratio of the minimum to the maximum small signal voltage gain is ________ (rounded off to two decimal places).
Diode circuit. The input V_in is applied through a 2 kilo-ohm resistor to node V_out. From V_out, a second 2 kilo-ohm resistor and a diode D (anode at V_out) are in parallel to a right-hand node, which connects to ground through a third 2 kilo-ohm resistor. V_out is measured from the node to the bottom wire. The inset shows the diode characteristic: zero current below 0.7 volt, then a vertical rise at 0.7 volt+−Vin2 kΩ2 kΩD2 kΩ+−Vout2010000.7VD (V)ID (mA)

Answer: Official key: 0.70 to 0.80

  1. The diode is ideal with a knee: off below , and on it holds exactly whatever the current. There are two regions to solve.
  2. Diode off. The three resistors are in series, so and the gain is . The diode voltage is the drop across the middle resistor, , so it stays off until , that is .
  3. Diode on. With the voltage at the right-hand node, . The current through the first resistor, , equals the current into the last resistor, . So and . The gain is .
  4. The maximum gain is (diode off) and the minimum is (diode on). Ratio .

Trap: taking maximum over minimum, . The question asks minimum over maximum, and is outside the official range 0.70 to 0.80. The code solved the diode on/off nodal equations over from to and took the numerical slope: minimum 0.500, maximum 0.667, ratio 0.750.

Where this shows up in industry

A diode across a resistor in a divider makes the gain change once the diode conducts. Simple wave-shaping and piecewise-linear function circuits work this way, and the constant 0.7 V drop used here is the hand-check model engineers apply before a SPICE run.

GATE 2023 · EC · Q.40MCQ · 2 marksDiode circuits: clippers, clampers, rectifiers and Zener regulators

Two anti-parallel silicon diodes (0.7 V cut-in) between VIN and VOUT, 1 kOhm to a 1 V battery: transfer curve?

In the circuit shown below, and are silicon diodes with cut-in voltage of . and are input and output voltages in volts. The transfer characteristic is
Two silicon diodes in anti-parallel between VIN and VOUT: D1 conducts from VIN to VOUT, D2 conducts from VOUT to VIN. The output node VOUT is also connected through a 1 kilo-ohm resistor to the positive terminal of a 1 volt battery whose negative terminal is groundedVIND1D2VOUT1 kΩ+−1 V
  1. (A)Plot A: slope-one line, flat at VOUT = 1 V between VIN = 0.3 V and 1.7 V, then slope-one againVINVOUT0.31.71
  2. (B)Plot B: slope-one line with a flat piece at VOUT = 0 V between VIN = -0.7 V and 0.7 VVINVOUT−0.70.7
  3. (C)Plot C: slope-one line, flat at VOUT = 1 V between VIN = -1.7 V and 1.7 V, then slope-one againVINVOUT−1.71.71
  4. (D)Plot D: slope-one line, flat at VOUT = 0 V between VIN = 0.3 V and 1.7 V, then slope-one againVINVOUT0.31.7

Answer: (A) Official key: A

  1. The 1 kΩ resistor carries current only if a diode conducts. With both diodes off, no current flows in it, so (the battery voltage).
  2. (anode at ) turns on when . At that moment , so . Above that, and the resistor current is positive.
  3. (anode at ) turns on when . With , . Below that, .
  4. So the curve is flat at for and has slope on both sides, passing through and . That is curve (A).

Trap: ignoring the battery. Then the flat piece is at between and , which is curve (B). The battery moves both the level and the two corners by . We solved the circuit for from to , testing all diode states for consistency, and compared with the sampled curve of each plot. Only (A) matches (largest error below ), the flat piece runs from 0.30 V to 1.70 V, and the same model with a 0 V battery reproduces (B) exactly.

Where this shows up in industry

A two-diode clipper with a bias voltage sets the clipping levels of a signal path, as in input protection and limiter stages ahead of comparators and ADCs. Real diodes round the corners because the drop is not constant, so designers check the clipped level at the actual current.

GATE 2024 · EC · Q.23MCQ · 1 markDiode circuits: clippers, clampers, rectifiers and Zener regulators

Centre-tapped full-wave rectifier, ideal diodes, V_s = 10 sin(wt), average V_L = 2.5/pi: transformer ratio n?

In the circuit shown, the step-down transformer and the diodes are ideal. The diodes have no voltage drop in forward biased condition. If the input voltage (in Volts) is and the average value of load voltage (in Volts) is , the value of is ______.
A centre-tapped transformer with ratio n to 1, driven by the source V_s(t) on the primary. The secondary has two halves with a centre tap. Diode D1 joins the top end of the secondary to the right node and diode D2 joins the bottom end to the same node, both pointing towards that node. The load R_L joins the centre tap to the right node. V_L(t) is measured across R_L with plus on the right noden : 1Vs(t)D1D2RL−+VL(t)
  1. (A)4
  2. (B)8
  3. (C)12
  4. (D)16

Answer: (A) Official key: A

  1. The secondary has a centre tap, so each diode sees half of the secondary. D1 conducts when the top end is positive against the tap and D2 when the bottom end is positive. With ideal diodes is the absolute value of one half-winding voltage: a full-wave rectified sine.
  2. The ratio is primary to the whole secondary, so the whole secondary has peak and each half has peak .
  3. Average of a full-wave rectified sine: .
  4. Set , which gives : option (A).

Trap: giving each half the whole secondary peak gives and , option (B). We averaged a sampled rectified sine for all four options: only gives 0.79577 V, which is ; with the wrong half-winding voltage only would have matched.

Where this shows up in industry

Centre-tapped full-wave rectifiers are used in low-voltage, high-current supplies, such as 5 V logic rails, because only one diode drop is in the current path at a time, against two in a bridge. Output stages of forward converters use the same arrangement with Schottky diodes.

GATE 2024 · EC · Q.35NAT · 1 markDiode circuits: clippers, clampers, rectifiers and Zener regulators

10 uF at 10 V discharges through 10 kohm and a 5 V ideal Zener: energy dissipated in the Zener in mJ?

As shown in the circuit, the initial voltage across the capacitor is , with the switch being open. The switch is then closed at . The total energy dissipated in the ideal Zener diode () after the switch is closed (in mJ, rounded off to three decimal places) is __________.
A series loop of an open switch that closes at t = 0, a capacitor of 10 microfarad with 10 V initial voltage (plus on its top plate), a Zener diode with V_Z of 5 V whose cathode faces the resistor, and a 10 kilohm resistor on the left branch. The Zener cathode is the upper end, towards the resistort = 010 μF+−V(0−) = 10 V10 kΩVZ = 5 V

Answer: Official key: 0.250 to 0.250

  1. The current leaves the capacitor plus plate, goes through the resistor and enters the Zener at its cathode. So the Zener is reverse biased: it conducts only in breakdown and then holds exactly across itself.
  2. While the current is . The capacitor falls to and stops there, because with no current is left to drive breakdown: with .
  3. The charge that flows is .
  4. The Zener voltage is constant at , so its energy is .
  5. Check: the capacitor loses in all, and the resistor takes the other . Together .

Trap: using the whole initial energy , or the whole energy lost by the capacitor, 0.375 mJ, as if the Zener alone took it. The resistor also dissipates (0.125 mJ). We stepped the discharge in time with a piecewise Zener and checked that the Zener, resistor and capacitor energies add up. Only 0.250 mJ is inside the official range.

Where this shows up in industry

A Zener clamp in series with a resistor sets how much of a stored charge a protection or reference circuit must burn off, and the Zener power rating has to cover the energy of the pulse. Voltage-clamp and ESD-protection networks are sized the same way.

GATE 2025 · EC · Q.57MSQ · 2 marksDiode circuits: clippers, clampers, rectifiers and Zener regulators

Ideal diode bridge feeding R: which plots of V_O or I_I against V_I (swept from -M to M) are correct?

All the diodes in the circuit given below are ideal.
Which of the following plots is/are correct when (in Volts) is swept from to ?
A full diode bridge across the input V_I, whose plus terminal is at the top. The four diodes are arranged around a diamond: the left node joins the anodes of the two left diodes, the right node joins the cathodes of the two right diodes, the top node (plus input) joins the cathode of the top-left diode and the anode of the top-right diode, and the bottom node (minus input) joins the cathode of the bottom-left diode and the anode of the bottom-right diode. A resistor R connects the left and right nodes. The output V_O is marked minus at the left and plus at the right, and the input current I_I enters at the plus terminal+−VIIIR−VO+
  1. (A)Plot of V_O against V_I: a V shape, zero at the origin, rising to M at V_I = minus M and at V_I = plus MVIVOM−MM
  2. (B)Plot of V_O against V_I: a straight line through the origin from minus M at V_I = minus M to M at V_I = plus MVIVOM−MM−M
  3. (C)Plot of I_I against V_I: a V shape, zero at the origin, rising to M over R at V_I = minus M and at V_I = plus MVIIIM/R−MM
  4. (D)Plot of I_I against V_I: a straight line through the origin from minus M over R at V_I = minus M to M over R at V_I = plus MVIIIM/R−M/RM−M

Answer: (A) and (D) Official key: A;D

  1. For the top terminal is positive. The current goes through the top-right diode, through from the right node to the left node, and back through the bottom-left diode. Two ideal diodes are in series and drop nothing, so and , flowing into the terminal.
  2. For the bottom terminal is positive. The current goes through the bottom-right diode, through again from right to left, and out through the top-left diode. is still positive, , but now the current leaves the terminal, so with drawn into it, (negative).
  3. So is a V shape: plot (A) is correct, and (B) is wrong. The input current is a straight line through the origin with both signs: plot (D) is correct, and (C) is wrong because it shows the magnitude.

Trap: picking (C) instead of (D). The load current in is , but is defined into the input terminal and changes sign when does. We enumerated all 16 on/off states of the four diodes at 41 values of , kept the one state that is consistent (on diodes conduct, off diodes are reverse biased), and compared and with each plot: only (A) and (D) match.

Where this shows up in industry

The diode bridge is the front end of almost every mains adapter and bench supply. With real silicon diodes two drops of about are lost in every conduction path, which is why low-voltage supplies use Schottky or synchronous (MOSFET) bridges.

GATE 2025 · EC · Q.61NAT · 2 marksDiode circuits: clippers, clampers, rectifiers and Zener regulators

Ideal diode, 5 V battery and R in series, V_I = 10 sin(100 pi t): forward-biased time per period?

The diode in the circuit shown below is ideal. The input voltage (in Volts) is given by , where time is in seconds.
The time duration (in ms, rounded off to two decimal places) for which the diode is forward biased during one period of the input is ___________.
A series loop: input V_I (plus terminal at the top) feeds a resistor R, then a diode whose anode faces the resistor and whose cathode faces down, then a 5 V battery, then back to the minus terminal. The battery's longer plate (its plus side) is the lower one, so its minus side is joined to the diode cathodeR5 V+−VI

Answer: Official key: 13.32 to 13.34

  1. The period is .
  2. The battery symbol has its longer plate (the side) at the bottom, so its side faces the diode cathode. Going round the loop, the battery adds to the input: the diode is forward biased when , that is .
  3. means . In one cycle the sine is below only from to , an angle of . So the diode conducts for .
  4. Time .

Trap: reading the battery the other way round. Then the diode conducts only for , from to , giving 6.67 ms, which is outside the key range. We stepped through one period in time steps and counted the time with : 13.33 ms.

Where this shows up in industry

A diode with a series resistor to a fixed voltage is the basic input-protection clamp: the diode conducts only when the signal goes beyond the reference, and the resistor limits the clamp current. The same circuit with the opposite polarity is a level-shifted clipper.

GATE 2026 · EC · Q.65NAT · 2 marksDiode circuits: clippers, clampers, rectifiers and Zener regulators

Ideal diodes D1, D2 with 2 V and 4 V batteries and 10 kOhm resistors, vi = 6 sin(wt): maximum of vo

Consider the ideal diodes D1 and D2 as shown in the Figure with cut-in voltage Volt and is in Volt.
The maximum voltage (Volt) of the output is __.
(rounded off to two decimal places)
Sine source vi(t) = 6 sin(omega t) in series with 10 kilo-ohm. Across the output vo(t), plus on top, two branches to ground: a 10 kilo-ohm resistor with diode D1 (anode up) and a 2 volt battery whose positive plate faces the diode; and diode D2 (anode down, cathode at the output) with a 4 volt battery whose positive plate faces the diodevi(t)10 kΩ10 kΩD12 VD24 V+−vo(t)vi(t) = 6 sin(ωt)

Answer: Official key: 3.70 to 4.30

  1. D2 has its anode at the positive plate of the battery and its cathode on the output node. So D2 conducts whenever , and while it conducts it holds (ideal diode, ).
  2. D1 sits in series with a and the battery. It conducts when .
  3. Try D2 on: . D1 is on too, since , and it draws . The source branch supplies , and the rest of the comes through D2. D2's current is , which is for every .
  4. So D2 stays on for the whole cycle, and the output is held at . At the peak the D2 current just reaches zero, which also matches the D2-off case: .
  5. The maximum output voltage is .

Trap: assuming both diodes are off at the top of the sine, so that follows up to . With nothing forces D2 off in that picture, but D1 is already on from and pulls the node down. We tested all four on/off combinations of D1 and D2 at 4000 points of one period and kept the one consistent with the diode currents. The output was at every point, with a peak and a minimum of and .

Where this shows up in industry

Diode and battery (or Zener) limiter networks like this protect ADC and sensor inputs: a diode to a reference rail stops the node from going past it, and a series resistor limits the current. Real diodes have a drop of about to , so the clamp level shifts by that amount.

From GATE prep to a electronics hardware career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.