Week 8 - Challenge 1 - Base Bracket Design

AIM:- To create an assembly for the given styling surafce. Objective:-  The objective of this project is to design car roof with essential flanges and reinforcements like ditch area,front roof rail,bow roofs, central roof rail and rear roof rail for the the given styling surface. Perform a curvature study on the roof…

AIM:- To Calculate the Wheel Arch gap at required points and check whether the car passes the European standard.   Fender:- Fender is a part of an automobile, motorcycle or other vehicle body that frames a wheel well (the fender underside).Its primary purpose is to prevent sand, mud, rocks, liquids, and other road…

AIM:- To write a report on what is underbody coating,it's type and pros and cons.   INTRODUCTION: WHAT IS UNDERBODY COATING? Underbody coating is a thick cladding (typically made of rubber) that is placed uniformly to the car’s underside. When the automobile is fresh off the lot and spotless, it is usually sprayed or painted…

AIM:- To write report explaining what is Bench-Marking with comparison of 4 vehicles.   WHAT IS BENCHMARKING?         Benchmarking in the automobile industry involves a structured comparisonbetween similar products services or procesess on some dimensions of performance.   Buying a Car is…

AIM:- TO CREATE A PILLAR DESIGN WITH MASTER SECTION.      Given Data:- Class A Surface Master Section   A Pillar:- The A pillar is the frame of the windshield that is between the windshield & the front doors.All cars with a windshield come with an A pillar.The B pillars are located behind the front…

AIM:-To create assembly for Quick Return mechanism and C.V. JOINT.   INTRODUCTION:- 1)QUICK RETURN MECHANISM:- The Quick return mechanism is the inversion of a single slider crank chain.The main purpose of this mechanism is to convert the rotary motion of the crank into reciprocating motion of the ram.A Quick return…

AIM:- To Create The Heat Stakes and Locators on Door Applique part.   LOCATORS:- Locators are used to arrest the Degrees of freedom of a component, there are many ways of creating locators based on the model, here for this model , I have created four way n two locators at corner position.    The Locators…

AIM:- To create the Dog House for the Door Trim.   DOG HOUSE:- Dog HOuse is an engineering feature used in plastic trim design.Dog houses are used as supporting feature. The primary function of Dog House is to avoid SINKMARK.   DRAFT ANALYSIS:-Draft analysis is required to check if a part has required draft…

Note:- As I am using Latest version of Catia,the MODEL is checked in session.   AIM:- TO CREATE THE RIB FOR THE DRILL HANDLE CONSIDERING DESIGN RULE.    Rib & Screw Boss are the Engineering Features which is on "B surface",They have some Design Rules to avoid Plastic defects.        …

Aim:-To create Core & Cavity block for switch Bezel. Draft analysis:- Draft analysis is required to check if a part has required draft or not. The draft analysis refers to a Tool that allows us to deteermine if we can remove the part we are designing.Here I used Analysis option, change the mode into material view first…

AIM:- To create the Bumper Plastic component through given class A surfcae. Draft Analysis:-Draft analysis is required to check if a part has required draft or not.The draft analysis referes to a Tool that allows us to determine if we can remove the part we are designing from the tool being used to design it.Here, i uesed…

TOOLING AXIS ,DRAF ANALYSIS & PLASTIC COMPONENT CREATION OF COIN HOLDER AIM:- The main aim of this challenge is to create the plastic component through the given CLASS -A suraface by craeting Tooling Direction & Draft analysis. INTRODUCTION:- The Draft Analysis command enable us to detect if the part can be drafted or…

TOOLING AXIX, DRAFT ANALYSIS & PLASTIC COMPONENT CREATION OF BACE BRACKET AIM:- The main aim of this challenge is to create th eplastic component through the given Class A Surface by creating Tooling Direction & DRaft analysis.   INTRODUCTION:-  The Draft Analysis command enable us to identify if the…

 TOOLING AXIS , DRAFT ANALYSIS & PLASTIC COMPONENT CREATION OF SWITCH BEZEL  Aim:- The main aim of this challenge is to create the plastic component through the given Class- A surface by creating Tooling Direction & Draft anaylysis.   INTRODUCTION:- The Draft analysis command enables us to detect…

AIM:-  To write reports on assembly of chopper model.                                      “MODELING OF AMERICAN CHOPPER ON SOLIDWORKS”  INTRODUCTION  In this project we learn how to design assembly…

Aim - To model Radar mast and assembly of Yacht using Solidworks.   All views , fetaure tree and Reports are given below:   1)RADAR MAST Front view     Isometric View   Feature Tree         2)YACHT ASSEMBLY All views and feature tree are as follows.   Front_view  …

Aim:- To impliment control logic of a "Washing Machine" using Stateflow for the given sequence.                                       If the power supply is available ,the system gets activated. If the water supply is not…

Aim:- To make a simulink model of a doorbell using solenoid block.                                                                         …

Data Analysis:- is a process of collecting, transforming,and modelling data in order to discover the required information.Here we have a Thermodynamic data collected and we have to analysed from a data file using a python program.         This data file consist of a 17 columns of different different…

  POPT:-  is an array, Optimal values for the parameters so that the sum of squared residuals of f(xdata,*popt) - f(xdata, *popt) -ydata is minimized.In other words POPT is our coefficient, we have a,b,c,d are three unknowns so popt is going to be those values,Curve fit function is calculate them for…

Objective:- To write a program that solves the ODE which represents the equatiion of motion of a simple pendulum and to create an animation of it's motion. Governing equation:-   Theory:- In engineering ,ODE is used to describe th etransient behavior of a system. eg:- Simple pendulum The way the pendulum moves…

AIM:- To write Python code that  can solve an Otto Cycle and make plots for it. Theory:-  An otto cycle is an idealised thermodynamic cycle that describes the functioning of a typical saprk ignition piston engine. Otto Cycle has main four procesess as shown below:-      Process 1-2 Isentropic Compression…

AIM:- To create a Rankine cycle simulator using MATLAB. Calculating all the states points of the cycle baesd on User inputs. Plotting T vs S & H vs S plot for the given input.   RANKINE CYCLE Rankine cycle is the process used in power plants. In this mechanism, a fuel is used to produce heat within a boiler,converting…

AIM:-  To write a MATLAB code for parsing the NASA thermodynamic data file and to extract 14 coefficients thermodynamic properties like Cp,H,& S,for all species in the data file. To find out the molecular mass of each species & finally to plot a graph of enthalpy,entropy & sp.heat with respect to Temprature.…

AIM:-  To write a code in Matlab to optimize the Stalagmite function and find Global Maxima of the function.   Theory:-   Genetic Algorithm is a search -based optimisation technique.GA is based upon Evaluation theory propossed by Charle's Darvin and matlab has built in function for GA.The genetic…

AIM:- Simulation of Simple Pendulum Objective:-   To write a program that solves the ODE which represents the equation of motion of a simple pendulum with damping.  Write a program in Matlab that will simulate the pendulum motion.   Theory:- A simple pendulum consist of mass m suspended with string having length L, when…