Week 11 - Final project

  To Route the following harness layout in the Electrical workbench and to add protective covering on all branches connected to DT06-2S & DT06-4S connectors. CAD data of the following Connectors: DT06-4S DT06-6S DT06-2S DT06-08SA PROCEDURE: Download connector 3D data from te.com Converting the Mechanical…

1ans) Create the Points and Planes in Part Design Work Bench. Define the part as support in Eletrical Part Design Workbench. Select the point and Plane for First entry point and Select the exit plane and base plane. Similarly Select the point and Plane for Second entry point and the exit plane will be automatically…

To define connectors and connector clip with necessary electrical geometrical conditions and definitions in electrical part design. Approach : Download Connector 3D - The 3D model of the connector is downloaded from websites provided in challenge box.  Create required Geometrical Parameters - The…

Designing of Back door assy for a car using NX CAD12  with all necessary reinforcements using provided class A surface of outer panel. Back door: Backdoor are one of the type of door of the vehicle which are located next to the passanger seat which provides access to the luggage compartment. In the most of the…

Designing and development of vehicle interior door trim using Catia V5 with provided class A surface along with Master section and also to create the engineering features as per design rules.  OBJECTIVE: To create thickened part using master section for reference. To create the mounting features as per design guidelines…

Design of roof and implemention of reinforcements and flanges with appropriate dimensions and verify the design by performing Heat Distortion, Snow Load. Roof:- An automobile roof is the portion of an automobile that “sits above the passenger compartment, protecting the vehicle occupants from sun,…

To design the fender with provided Master section data and Styling surface of fender as Input.   Front fender: Front fender is a part of the vehicle that frames the wheel. The primary purpose of the fender is to prevent sand, mud, rock etc. from being thrown away into the air by rotating tire. Fender can be 2 types…

Calculation of section modulus and optimization of the Hood Section modulus: Section modulus is a geometric property for a given cross-section used in the design of beams or flexural members. The elastic section modulus is defined as S = I / y, where I is the second moment of area (or area moment of inertia) and y is the…

  To examine the given fender design to verify if the wheel arch of the fender meets the European standards.   Fender:Fender is the part of a vehicle that surrounds the wheel. Apart from being the exterior aesthetic part of the vehicle, its important function is to prevent debris such as mud, gravel, rocks, fluids…

Design & Assemble Hood outer panel, inner panel and the necessary reinforcements by following the Design parameters & using provided Master section. Abstract:The project report deals with the explanation of steps and procedure followed while developing the HOOD Assembly of a car using CATIA V5. Using the styling…

  CASE STUDY ON  UNDER BODY COATING FOR AUTOMOBILES: Definition:Under body coating is a type of defensive layer that’s applied to the undercarriage of cars. These sections are close to significant deterioration all of the time.While Driving on roads, tiny specks like mud, water, dust etc..from the ground…

                                                     CASE STUDY-1   SCOPE: BENCHMARKING OF AVAILABLE CARS IN 5-10 LAKHS AND SUGGESTING THE BETTER OPTION IN THE SEGMENT FOR A BUYIER…

Creation of solid component of A pillar using given Class A surface and adding engineering features like dog house to the A pillar using given Master section and performing draft analysis to the final component. A pillar: Pillar refer to roof pillars, and they're lettered front to back. A-Pillars straddle the windshield.…

Creation of solid component of door trim lower using given Class A surface and adding engineering features like 2 way , 4 way locators and heat stakes to the Door trim lower and performing draft analysis to the final component. Door trim lower: An interior component attatched to the inner side of the door. This product…

Creation of solid component of door trim using given Class A surface and adding engineering features like dog house to the Door trim and performing draft analysis to the final component. Door trim: An interior component attatched to the inner side of the door. This product will merely improve the appearence to the vehicle…

Creation of solid model of Door handle by using Class A surface and also adding engineering features like ribs and screw boss to door handle and also to perform draft analysis on class A and final component.   Door handle:A Door Handle is built to detach the door latch to enable the door's opening. Important…

Creation of solid model of Switch bezel component using its Class A surface and to perform Draft analysis on Class A surface and also on Final output solid switch bezel and followed by designing of CORE BLOCK , CAVITY BLOCK and creation of parting surface and parting line for the created Switch bezel.  Major terminoligies…

Creation of solid model of Bumper using given Class A surface of bumper and also to do draft analysis on both final solid model and also on given Class A surface. Bumper: A bumper is a structure attached to or integrated with the front and rear ends of a motor vehicle, to absorb impact in a minor collision, ideally…

Creation of solid model of Switch bezel component using its Class A surface and to perform Draft analysis on Class A surface and also on Final output solid switch bezel.   Switch bezel:Switch Bezels in car are parts which contains switches and controls for different functions like Window control, Door lock/Unlock,Media…

Title: Creation of soild model of coin holder using its Class A surface and also performing draft analysis on coin holder. Steps followed to create tooling axis: In this particular , the major portion of model is bin area and so we conclude that the tooing axis will pass through this bin area . next after , we extract…

Creating solid model using given CLASS A surface of base bracket and also t do draft analysis on base bracket. Major terminologies:  Draft analysis: This is a kind of analysis made on a part. By draft analysing we can judge  the created part is easily removable from core and cavity  or not. This analysis…

1)       2)PART- MODELLING, ASSEMBLY AND PHOTOREALISTIC RENDERING OF THE YATCH AIM: To model the sunseeker yatch using solid works software. OBJECTIVE: Modelling of all parts of yatch and assemble it. Getting familiar with hybrid modelling(ie., solid / surface modelling) during modelling. INTRODUCTION:…

PROJECT  1: PART MODELLING, ASSEMBLY AND PHOTO REALISTIC RENDERING OF AMERICAN CHOPPER     OBJECTIVE: To do part modelling of American chopper part wise using solidworks software. Assemble the complete chopper and to do Photo realistic rendering in the solidworkds software itself. To do the modelling with…