MODELING OF AMERICAN CHOPPER  ON SOLIDWORKS By Santhoshsivan. G     INTRODUCTION      This project we learn the entire modeling of an American chopper in solidworks and also, we learn how to render the model (American chopper) in solidworks visualize.      The different types of components used for built the chopper are…

1.RADAR MAST 1.Front view 2.Right side view 3.Isometric view 4.History tree 1 5.History tree 2 6.History tree 3 7.History tree 4 2.YACHT ASSEMBLY Modelling of yacht tutorial on solid works By Santhoshsivan.G Introduction In this project we are learn to sketch entire model of yatch tutorial on solid works by using some…

Modelling of Casing in Siemens  PLM NX 12 By Santhoshsivan.G Introduction:       In this model, we learn how to create casing model on siemens PLM NX 12 by using some tools like tab, datum, Cutout, Bend, unbend, flange, etc.      This are the following tools use to create casing…

Modelling of Box Assembly in Siemens PLM NX 12 By Santhoshsivan.G Introduction         In this model, we learn how to create box assemble on siemens PLM NX 12 by using some tools like tab, datum, normal cut out, Bend, unbend, flange, etc.        This are the following…

Modelling of Bracket in Siemens PLM NX 12       By  Santhoshsivan.G Introduction         In this model, we learn how to create casing model on siemens PLM NX 12 by using some tools like datum, normal Cutout, Bend, unbend, contour flange, etc.       …

Modelling of odd shaped encloser in Siemens PLM NX 12 By Santhoshsivan.G   Introduction         In this model, we learn how to create odd shaped encloser model on siemens PLM NX 12 by using some tools like datum, jog, Bend, unbend, bead, extrude, etc.       …

Modelling of Metal Bracket in Siemens PLM NX 12                                    By     Santhoshsivan.G   Introduction         In this model, we learn how to create metal bracket model on siemens PLM NX 12 by using some tools like datum, normal Cut-out, Bend, unbend, contour flange, etc.        This are the following…

BENCH MARKING santhosh sivan Benchmarking:                  Benchmarking means continuous improvement and continuous growing for the organization. Also, to facing the challenges from the market. Benchmarking is the process of comparing and…

Under Body Coating By Santhosh sivan. G Under Body Coating, its types, Advantage and Dis-advantages: Under seal is a thick resilient coating applied to the underbody or chassis of an automobile to protect against impact damage from small stones, which would rapidly chip ordinary paint, allowing rusting to begin. Underbody…

Hood Design                                                            By Santhosh Sivan.G     Introduction         Hood is also…

                                                                                           …

Fender Design Abstract To create the fender with help of Siemens NX 12. santhosh sivan Introduction        The fender is curved shape structure which is located by side of all vehicles and it coves the wheel and protect the passenger for small rocks, sand and some other particle which thrown…

SECTION MODULAs CALCULATION AND OPTIMIZATION santhosh sivan   INTRODUCTION OF SECTION MODULUS:             What is mean by section modulus.?. Section modulus is the geometric property of the given cross-section of any shaft or other beam structure.it is the direct measure of the strength of the shaft section or the beam…

                                                                                          …

BAck Door Design Santhosh sivan. G   Introduction   The Back Door of a car is the rearmost part of the vehicle which gives access to the trunk space of the vehicle. The rear door also supports the reinforcements and added weights of the Wiper Motor, Gas Stay, Tail Lamp, and Latch and Striker.          The Backdoor/tailgate…

A.Quick Return mechanism: 1Body (Part): Isometric, Front, Side and Top Views: History tree: 2D Drawing: 2.Pin: Isometric, front,side and top views: History tree: 2D drawing: 3.Pin 2: Isometric, front, side and top views: History tree: 2D drawing: 4.Sliding Guid way: isometric, front, side and top views: History tree: 2D…