Create a Teramesh for Housing component with the following quality criteria. TetraMesh Generation Method: 2D to 3D Conversion Elements sizes: Min- 2 Units, Target- 5 Units, Max- 7 Units  Tet collapse: 0.15 Aim: To Create a Teramesh for Housing component with the following quality criteria Elements sizes: Min- 2 Units,…

AIM: Create connector and Attach the various parts of the given model  1. Right_Rail_2 & Front_truss_1:- Seam-Quad(angled+capped+L) 2. Left_Rail_2 & Front_truss_1:- Quad elements 3. Front_truss_2, Front_truss_1 & Right_Rail_1:- Spot weld with 2 Layers and 5…

OBJECTIVE: Follow the below-mentioned quality criteria, mesh the component given below and assign thickness: Target Element Length = 5 Units S.N Quality Criteria  Value  1 Aspect Ratio  5 2 Skewness 45 3 Warping 15 4 Taper      0.5 5 Min. Length 2 Units 6 Max. Length 8 Units 7 Min angle Quad…

AIM: Follow the Quality Criteria and mesh the following component and assign thickness: Target Element Length = 4 Units S.N Quality Criteria  Value  1 Aspect Ratio  5 2 Skewness 45 3 Warping 15 4 Taper      0.5 5 Min. Length 2 Units 6 Max. Length 6 Units 7 Min angle Quad 45 8 Max angle Quad…

OBJECTIVE: To Carry out the geometry cleanup operation on the given 3 files. Practice  Clip Repair Mounting Bracket There should not be any free edges, convert all of them into refine geometry. Clean the geometry. Extract midsurface. Clean midsurface geometry. Ignore holes less than dia 5mm. Create 2D mesh with target…

OBJECTIVE: To check the material properties of the rail component and calculate the speed of sound in steel rail To calculate the time takes for a shock wave to travel from one end of the rail to the other. To calculate Time for sound to travel length of rail To Edit the engine file so that…

AIM: Comparison of results with base simulation and improved shell element properties 1.Using the crash beam file from the previous assignment, change the run time to 55 ms. 2. Change the number of animation steps during simulation to a minimum of 25 and maximum of 60. 3. Run the base simulation without any modification…

AIM:Run the given model with given material properties and then compare the results. Perform the simulation as per the cases given below. Case 1  Import the FAILURE_JOHNSON_0000.rad file and run the model as it is. Give the title name as Law2_epsmax_failure. Case 2 Import the case 1 rad file, named “Law2_epsmax_failure” and…

AIM: To Create the mesh for bumper assembly,mesh size should be 6mm.  Run the crash tube model as it is.Change the Inacti=6 and run.Create the type 11 contact and run.Remove both notches  and remove boundary condition on rigid body node then run.Create a new notch in the middle ,select the whole section…

OBJECTIVE : To perform frontal crash analysis of a vehicle against a rigid wall in Hypermesh. To simulate the crash behavior of the vehicle in HyperView and discuss the results. To plot the sectional and axial forces at different locations and discuss the results. To obtain intrusion results at dash wall and plot them…

Objective: The objective of this project is to perform 2D shell meshing for the hood component of a car. After meshing, component thickness and material need to be assigned to the mesh. And the mesh should follow the following quality criteria, S.no. Quality criteria Value 1 Target/Average length 5 2 Minimum Length 2 3…

#Normals check and correctset a .windowcatch {destroy $a}toplevel $a -class Toplevelwm title $a "Normals"wm geometry $a  300x100+200+50; updatewm resizable $a 1 1wm deiconify $abutton $a.01 -text "Normals" -command {normals} -bg white -font {times 12 bold};     place $a.01 -x 20 -y 50 -width 100 -height…

Iam unable to submit the challenge in this text box as it is not getting submitted I have attached word document.Kindly consider that.