AMERICAN CHOPPER AIM AND OBJECTIVE:                                 To sketch and design every exterior part of the chopper under a part modelling environment with suitable sketches and commands using Solidworks. To assembled the modelled…

  PREDATOR YACHT   Aim and Objective:                            The objective is to design and assemble various parts of the yacht using Solidworks. Introduction:                    The yacht includes both part modelling and surface modelling. The surface modelling is used up to 90% in the modelling of various parts of…

  NX CASING   Introduction:                       The casing is a sheet metal part that is created in Nx software. With various commands sheet has been created. Description:                     First…

BOX ASSEMBLY:  

                                                                                 ODD SHAPED ENCLOSURE   Introduction:…

                                                                                           …

                                                                                           BRACKET…

Q-1 Ans:              I would like to suggest some cars like Hyundai Venue, Tata Nexon, Maruti Suzuki Brezza, Mahindra XUV 300, and KIA Sonet. But these vehicles are in mid-range not top-end some of the cars are starting from 8 to 9 lacs on road. He loves big cars that's why I suggest…

Que:  Write a one-pager about Under-Body Coating and its purpose, its types in detail, and its pros and cons. Ans: Under-Body coatings are those which are used to prevent a car's underbody from rusting and corrosion. This underbody coating is preventing from rusting, and bad road conditions…

                                                                                           …

Aim:          To create a report on fender regulation and calculate the wheel Arch area and prove whether the car will pass the standards or Not by Using the European Standards. Fender:             A fender is the part of a car that protects and frames its…

                                                                                           …

                                                                             SECTION MODULUS OF THE HOOD Objective: To find…

                                                                                       ROOF ASSEMBLY…

    DRAFTING ANALYSIS ON BASE BRACKET CLASS A SURFACE AND CREATING PLASTIC COMPONENT FROM IT:    DRAFTING:    When developing parts for plastic injection molding, applying draft (or a taper) to the faces of the part is critical to improving the moldability of your part. Without it, parts run…

                                                                  Challenge 2 - Switch Bezel Design   Aim       Create the Switch Bezel…

                                                                                          Challenge…

                                                                                     Challenge 3 - Coin Holder…

                                                          Attachment Feature Creation (Ribs & Screw Boss) - Challenge 1    Aim        1. To create…

                                                                      Attachment Feature Creation - Challenge 2   AIM: Create the Dog House…

                                                       Project 1 - Door Trim Lower with Engineering Features DOOR TRIM LOWER Aim: To Create the Door trim lower component through the…

                                                                        Assembly Workbench   Assembly Workbench 1: Assembly Images:…

                                                       Project - A pillar Design with Master Section   Objective: The main objective of this challenge is to understand the given…

                                                           Challenge 6 - Core & Cavity Design Objective: The main objective of this challenge is to design a Core…

                                                                         Report On Car Back Door Design     Aim-  To design the Back door of the car using the appropriate design methodologies, providing the necessary Reinforcements and embosses in the inner panel for strength. Design Considerations for a Back Door- Rear…

                                                     Wiring harness design in CATIA V5 - 3D modeling Week 2 Challenge   AIM:   To define Electrical properties of the given components.…

                                        Wiring harness routing & packaging Rules Week 3 Challenge                   AIM:   To solve the above assignment questions and…

                                                      Wiring harness design in CATIA V5 - 3D modeling Week 4 Challenge AIM: Route the following harness layout in Electrical workbench. Make…

                                                  Wiring harness design in CATIA V5 - 3D modeling Week 5 & 6 Challenge   Let, we have provided the harness layout as below and accordingly…

                                                 Wiring harness design in CATIA V5 - 3D modeling Week 7 Challenge   Q1. Flatten the harness assembly completed in “ week 4 challenge”.…

                                                                            Project 2   WIRING HARNESS FOR TAILGATE: AIM: To…

                                                                            Project 2   WIRING HARNESS FOR TAILGATE: AIM: To route the wiring harness for the given Tailgate. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as…

                                                           Project 1   AIM:           Route the wiring harness for the Bugatti V16 Engine assembly and prepare a flatten-view drawing in CATIA V5. OBJECTIVE:                     The objective of this project is to route the wiring harness and prepare the flatten-view drawing…

                                                                            Project 2   WIRING HARNESS FOR TAILGATE: AIM: To…

                                                   INTRODUCTION TO BIW AND FIXTURE CHALLENGE   1] What is BIW & define its parts? Ans: Body in white (BIW) refers to the stage in…

                                                    BIW FIXTURE BASICS CHALLENGE   1] What is the process of project execution activity? Ans:  PROCESS OF PROJECT EXECUTION ACTIVITY:…

  1] What is Design Methodology? Ans: DESIGN METHODOLOGIES:                                             In this methodology we learn about three design processes, we're going to study how do we proceed while…

                                                                                    PIN UNIT DESIGN CHALLANGE…

                                                                              REST UNIT & CLAMP UNIT DESIGN CHALLANGE   Aim:         To Design 3 Different types of Power Clamp units with Different risers, blades, and Clamp Arm for the given Car Panel and Design 2 Different types of Rest units for the given Car Panel. Rest…

                                                          Clamp Unit & Pin-Clamp Unit Design Challenge   OBJECTIVE:  To design 3 types of Swivel Clamp unit and 1…

                                                                                      Base Unit Design Challenges…