AIM : Create 1D elements on the following component with given cross-section and DOF .Mesh the Given component with the Size of 5 Units Of Elements with diamensions as , a. Rod element:- Translational DOF should be Constrained with RBE2 link Cross-Section: BOX- Dimension a= 12 mm        …

AIM : Mesh the component given below and assign thickness Target Element Length = 5 Units S.N Quality Criteria  Value  1 Aspect Ratio  5 2 Skewness 45 3 Warping 15 4 Taper      0.5 5 Min. Length 2 Units 6 Max. Length 8 Units 7 Min angle Quad 45 8 Max angle Quad 135 9 Min angle Tria…

                                                                                   Model 1   Aim :- Create…

Aim :- Mesh the given geometry. Provided below are the quality parameters that you have to follow. Target Element size - 5 Units S.N Quality Criteria  Value  1 Aspect Ratio  5 2 Skewness 45 3 Warping 15 4 Taper      0.5 5 Min. Length 2 Units 6 Max. Length 8 Units 7 Min angle Quad…

Aim:-  Follow the Quality Criteria and mesh the following component and assign thickness: Target Element Length = 4 Units S.N Quality Criteria  Value  1 Aspect Ratio  5 2 Skewness 45 3 Warping 15 4 Taper      0.5 5 Min. Length 2 Units 6 Max. Length 6 Units 7 Min angle Quad 45 8 Max angle Quad 135 9 Min angle Tria 20 10…

Aim :- Follow the below-mentioned quality criteria, mesh the component given below and assign thickness: Target Element Length = 5 Units S.N Quality Criteria  Value  1 Aspect Ratio  5 2 Skewness 45 3 Warping 15 4 Taper      0.5 5 Min. Length 2 Units 6 Max. Length 8 Units 7 Min angle Quad…

Aim :-For the given Hood model, Take the mid surface for all the components after checking the geometrical errors and mesh the mid surface with the given element Quality criteria. (Refer the table Below for the Quality criteria)    S.No  Quality Criteria  Value  1 Target/Average length  …

Aim :-  For the given Plastic Bottle Cap model, check for the geometrical errors and take the mid surface by suitable mid surfacing techniques. PID and Thickness assignment has to be done for all the mid surfaces. Mesh the same with given element Quality criteria. (Refer the table Below for the Quality criteria)  …

Aim :- For the given Intake Manifold component, check for the geometrical errors and mesh the Surfaces with the given 2D element Quality criterias given below.  S.No  Quality Criteria  Value  1 Target/Average length   3 2 Minimum Length  1 3 Maximum Length  5 Use tetra elements to…

Aim :-  For the given Rear view mirror component, check for the geometrical errors and mesh the Surfaces with the given 2D element Quality criterias given below.    S.No  Quality Criteria  Value  1 Target/Average length   1 2 Minimum Length  0.5 3 Maximum Length  2  …

6hours take to complete Switch panel model. 3 1/2 hours take to complete second model.

Aim :- the given Rear door FE model, Create and Apply different PIDs for different components. By using the same technique and the elements as shown in the video, Perform suitable connections. (No thickness need to be assigned to FE as intention is just to deploy connections).   Procedure :- Step  1 :- import…

                                                                                                                                                                  Model 1  Aim :-  Practice all the Morphing techniques that were shown in the video Procedure :-  Step 1 :- Import the model file -open -select iges file -open …

Aim :- For the given component, check for the geometrical errors and mesh with the given element Quality criteria. After meshing the component the thickness has to be assigned. Write a detailed report on your meshing process and also mention which method you used to extract the mid-surface along with the reason.  …

Aim:- For the given assembly, check for the geometrical errors and mesh with the given element Quality criteria. After meshing the component the thickness has to be assigned for mid surfaces. Use tetra elements to model non-uniform thickness components. Also use Appropriate connections to connect the component as suggested…

Aim :- Carry out the geometry cleanup operation on the given 3 files. Practice  Clip Repair Mounting Bracket There should not be any free edges, convert all of them into refine geometry. Clean the geometry. Extract midsurface. Clean midsurface geometry. Ignore holes less than dia 5mm. Create 2D mesh with target…

1. Check the material properties of the rail component and calculate the speed of sound in steel rail=_______? Ans :- Speed of the sound wave  C =root(E/density ) = root((210000)/(0.0078)) = 5188.745mm/ms 2. The length of the rail is about 1000 mm.calculate the time takes for a shock wave to travel from one end of the…

1.Using the crash beam file from the previous assignment changed the run time to 55 ms. 2. Changed the number of animation steps during simulation to a minimum of 25 and maximum of 60. Ans :- animation steps as 50            ANM/DT = 55/50 = 1.1   3. Run the base simulation without…

Case 1  Import the FAILURE_JOHNSON_0000.rad file and run the model as it is. Give the title name as Law2_epsmax_failure.   Ans: Import the model    Perform the simulation.   Simulation result with ploted graph with Energies                  f  Simulation…

Create the mesh for bumper assembly,mesh size should be 6mm.  Given Model.   Meshed Model with element size =6mm 1 . Run the crash tube model as it is. Ans :- Given Model:   Runned the model and ploted graph , Ploted a graph in internal enenrgy and contact energy.   Ploted Rigid wall forces .  …

COMPLETED THROUGHT LIVE SESSION : Aim:- Frontal crash-BIW Check unit system and either follow[Mg mm s] or [Kg mm ms]. Create appropriate interface ,friction 0.2 and recommended parameters. Make sure of no penetrations and intersection. Correct rigid bodies if any issues. Create rigid wall with friction 0.1. Compare the…