What is undercoating  Undercoating  is the type of paint coating to protect the body whit the rusting,  As we know a car's upper body is painted so they were protected the upper main body from rusting but at the bottom of the car  we can't be used any type of paint to protect the floor or bottom area…

What is Benchmarking? Benchmarking is a process where you measure your company's success against other similar companies to discover if there is a performance gap that can close by improving your performance. Studying other companies can highlight what it takes to enhance your company's efficiency and become a bigger player…

AUTOMOBILE HOOD DESIGN  Here we are going to understand and design the concept of the front-mounted engine hood according to the standards.  in this report, the flow information will be as follows What is the hood Materials use  Pedestrian- Vehicle Collision Data Designed  Conclusion   What is…

FENDER DESIGN- WHEEL ARCH        OBJECTIVE OF THE WHEEL ARCH  The main objective of the project is to calculate the wheel arch area and also conclude I the car will pass the European standards or not. because countries follow different regulations.    what is fender?  Fender is the…

FENDER DESIGN OBJECTIVE  The main objective of this project is to design the BIW(Body in white) of the front fender using the fender skin data and the master section as the data by using NX CAD. Introduction of Fender Fender is the American English term for the part of an automobile, motorcycle, or other vehicle body…

REPORT ON SECTION MODUL CALCULATION OF HOOD    OBJECT  To calculate the section modulus of the previously designed hood for analyzing its strength and also optimizing the design to see the difference in the bending strength of the hood. The higher the section modulus of a structure, the more resistive it…

CAR BACK DOOR    AIM: To design the back door of the car and make the inner panel for the back door and also design the necessary reinforcements. INTRODUCTION: The trunk (North American English) or boot (British English) of a car is the vehicle's main storage or cargo compartment, often a hatch at the rear of…

Car Roof Design And Analysis Of Reinforcements Objective: To develop the essential flanges and reinforcements with appropriate dimensions and check the draft by performing Draft analysis, Calculation of Section inertia, Heat distortion, and Snow load on the roof. Introduction: An automobile roof is the portion of an automobile…

AIM: Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. REPORT ON DRAFT ANALYSIS: Given Class A Surface: STEP…

Switch Bezel Design Objective- -To Create the Switch Bezel Plastic component through the given Class-A surface.the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and to perform the Draft analysis on the model.  -Take the Thickness of the component to be 2.5…

AIM:- Create the Coin Holder Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Take the Thickness of the component to be 2.5 mm…

AIM Create a Core and Cavity for the existing Switch Bezel design and Show Draft Analysis using the existing Tooling Axis. OBJECTIVE Create Parting Surface and Parting Line for Switch Bezel. Create Core And Cavity Blocks. Show Draft Analysis Component with the Core and Cavity. Make Solid a Body Using the Close Surface…

BUMPER DESIGN AIM: to make a model from the provided class-A surface.INTRODUCTION:CLASS-A SURFACE: a surface made by the designer which is given as input to the plastic modeler to work on. It is an aesthetic surfaceand the outermost surface.CLASS-B SURFACE: a surface below a certain thickness from the class-A…

DOOR TRIM LOWER AIM: to make a model from the provided class-A surface.INTRODUCTION:CLASS-A SURFACE: a surface made by the designer which is given as input to the plastic modeler to work on. It is an aesthetic surfaceand the outermost surface.CLASS-B SURFACE: a surface below a certain thickness from the…

                                                             Attachment Feature Creation (Ribs & Screw Boss) AIM: To Create the Door Handle Component from the given…

 SCREW BOSS AND DOG HOUSE DESIGN ON DOOR TRIM AIM- Create the s dog house for the DOOR TRIM   Doghouse wall thickness at the intersection of the part wall (C ) should be 40% or less than the main wall stock (T). The height of (B) should be between 3-6 mm Given  Door trim surface Making tooling Axis…

DOOR TRIM LOWER AIM: to make a model from the provided class-A surface AND Create the Heat Stakes and the locators considering the design rules mentioned in the video for the door applique.    INTRODUCTION: CLASS-A SURFACE: a surface made by the designer which is given as input to the plastic modeler…

AIM - TO CREATE THE DOG HOUSE WITH THE HELP OF MASTER SECTION  In this report, we use the master section to create a DOG HOUSE in  A-Pillar  Given surface Given the master section of dog House  Step 1-  Creating the tooling axis with the help of the Class A surface Step 2 - Checking the draft analysis…

4 Bar Quick Return Mechanism: First, we have to create the all parts of this mechanism and then assemble this.  Creation of the First part: Create the required sketch according to the given dimension. Then pad it       Creation of the second part:     Creation of third part:  Creation…

AIM To create a door interior part from the inputs of class A surface along with master section by following the design rules followed in tier 1 and OEM industries in CATIA v5 SOFTWARE USED CATIA V5 OBJECTIVES Create a sketch by using the Positioned sketch All the should be sketches should be Iso-Constrained Ensured Proper…

Advanced Sheet Metal Design Using NX Cad Challenge 1 Casing Design Title of the Project: Advanced Sheet Metal Design Using NX Cad Challenge 1 Casing Design Objective: To design a Casing with the help of NX advanced sheet metal. Introduction: NX Sheet Metal provides a set of tools within the NX design environment…

TITLE OF THE PROJECT: Advanced sheet metal design using Siemens NX cad - Box Assembly. OBJECTIVE: To design a box assembly and create a draft of it using Siemens NX Sheet metal application. INTRODUCTION Sheet metal is metal formed by an industrial process into thin, flat pieces. Sheet metal…

                                       ODD SHAPED ENCLOSURE  OBJECTIVE:- To design an odd-shaped enclosure and create a draft of it using the Siemens NX Sheet metal application.  INTRODUCTION:-   …

Objective: To design a Bracket using the Siemens NX Sheet metal application.   Introduction:-   1. SIEMENS NX:- NX formerly known as "Unigraphics", is an advanced high-end CAD/CAM/CAE, which has been owned since 2007 by Siemens PLM Software. 2. SHEET METAL DESIGN:- NX Sheet Metal Design provides the design professional…

METAL BRACKET USING NX SHEET METAL APPLICATION: OBJECTIVE: This is a project to learn the step-by-step procedure to create a Bracket with a gusset from the given 2D drawing.   DESIGN METHODOLOGY: SHEET METAL MODELING: Features and Tools: Contour Flange: Creates a base feature by extruding the sketch along a vector…

AIM: The objective of this project is to ASSEMBLE a BUTTERFLY VALVE and apply GD&T final assembly using Siemens NX.     INTRODUCTION  A butterfly valve is from a family of valves called quarter-turn valves. In operation, the valve is fully open or closed when the disc is rotated a quarter turn.…