OBJECTIVE:  The objective of this project is to derive and evaluate a second order derivative of a function by using Taylor’s Tabel method. The taylor table method is used to simplify the algebraic equation derived using Taylor series and to reduce processing time. Deriving the 4th Order Approximation of the…

OBJECTIVE: The objective of this project is to write a MATLAB code to solve 2D heat conduction for steady and unsteady states. For steady state we are going to solve with three iteratives method. Jacobi Method. Gauss Siedal Method. Successive Over Relaxation Method(SOR). For unsteady states we are going to use Implicit…

  OBJECTIVE: The objective of this project is to do a basic geometric check and the do a Surface & Volumetric mesh using ANSA, on the given turbocharger. Also to define the different targlent lengths on the respective PID's. TOOLS Used: Checks:         Checks is basically used to checks…

OBJECTIVE: The objective of this project is to do a basic geometric check and the do a Surface & Volumetric mesh using ANSA, on the given BMW M6 car model. Also to define the different targlent lengths on the respective PID's. TOOLS Used: Checks:         Checks is basically used to checks the…

OBJECTIVE: The objective of this project is to do a geometrical clean up and to delete unwanted surfaces on all the three given models and to merge them to perform a surface wrap to create a water tight mesh. TOOLS USED: TOPO: Universal Delete to delete unwanted surfaces on the models. CONS`rarr`Paste & Release the…

OBJECTIVE: The objective of this project is to do a basic geometric check and the do a Surface & Volumetric mesh using ANSA, on the given Tesla Cybertruck model. TOOLS Used: Checks:         Checks is basically used to checks the errors in the model.         Tools used under…

OBJECTIVE: The objective of this project is to set up steady-state simulations to compare the mixing effectiveness when hot inlet temperature is 360C & the Cold inlet is at 190C in a mixing tee model of varying lengths and to understand the effects caused on the liquid due to the varying lenghts of the pipes. `rarr`…

Aim:  The Aim of the experiment to set up a flow analysis over a 2D cylinder using Ansys fluent and study the Karman Vortex Street phenomena using steady and Transient flow conditions.  OBJECTIVE:  To simulate the flow with the steady and unsteady case and calculate the Strouhal Number for Re= 100 To calculate…

OBJECTIVE:  The objective of this project is to do an external flow simulation over Ahmed body and to study the nature of the flow in the wake region and forces such as drag and lift coefficient. ABSTRACT:  AHMED BODY:  The Ahmed body is a geometric entity that represents a standard passenger car. The geometry…

 OBJECTIVE:  The objective of this project is to perform a steady state conjugate heat transfer (CHT) analysis on an exhaust port.  Conjugate heat transfer (CHT):  Conjugate heat transfer is a type of heat transfer analysis between solids and fluids. This type of heat transfer includes both convective…

OBJECTIVE:  The objective of this project is to perform Rayleigh Taylor Instability simulation.  Theory:  Rayleigh Taylor Instability:  Rayleigh Taylor Instability (RTI) is a phenomenon that occurs at the interface of fluids of different densities wherein the lighter fluid pushes the heavier fluid due…

OBJECTIVE:   The objective of this project is to perform a steady state conjugate heat transfer (CHT) analysis on a graphics card.  To run the simulation by varying the velocity 1m/sec 3m/sec 5m/sec.  To find out the maximum temperature and heat transfer coefficient attained by the processor. …

Objective:  The objective of this project is to perform analysis on cyclone separator and calculate the separation efficiency and pressure drop.  To perform velocity versus particle size study from 1 m/s to 5m/s and for particle size from 1 micrometer to 5 micrometer. Tabulate the results and compare for…

Objective:          To perform parametric study on flow in gate valve to visualize the velocity contour, velocity vector and calculate the flow co-efficient for each case. We shall perform parametric study from 10 mm valve open position to gradually increase the opening in units of 10 mm up to…

Battery thermal managment system