MODELLING AND RENDERING OF AN AMERICAN CHOPPER BIKE  American chopper has been on television since 2003 and is one of the most popular motorcycling shows around. The series focuses on Paul   Teutul…

Aim;-To define the all the Mechanical&Electrical components into electrically defined and create a catalouge for the all components.Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties…

         AIM Downloading the p clamp following cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. Download following Back shell cad data & define it as Electrical back shell using Electrical Part design Workbench. Define…

             3D MODELLING,ASSEMBLY,AND PHOTOREALISTIC RENDERING OF SUNSEEKER PREDATOR YACHT The first Sunseeker Boats incorporated a creative combination of Scandinavian finesse and American built. They were the ones to first set a standard in terms of outdrive power. Daycab 23 and Sports 23 were the first vessels to be…

  OBJECTIVE: The objective of this project is to route the harness layout in electrical work bench Above picture shows the 2D schematic layout of the required harness.The follwing Deutsch connectors aer used in this harness. The follwing Deutsch connectors are used in this harness. DTO6-4S(QTY-2) DTO6-6S(QTY-1) DTO6-2S(QTY-2)…

    UNDERBODY COATING Underseal(often called undercoating in the U.S) is a thick resillient coating applied to the underbody or chassis of an automobile to project against impact damage from small stones,which would rapidly paint,allowing rusting to begin. The rate at which vehicles corrode is dependent upon:…

   AIM: Check the bundle Continuity. Add snap of result in submission Add annotation to all connectors. Make an assumptions for annotations like connect 1 , 2 etc Check for the bundle warning. Add snap. Generate CAT.part of harness assembly and convert is in. igs format. Let,We have provided the harness layout…

                                                          BENCHMARKING OBJECTIVE: Benchmark with presently avaliable cars in the market for the following case. Mr. D.S. Pughazhyendhii is…

AIM: To route the wiring harness on given engine and flatten view drawing in CATIA V5. INDROUCTION: Wiring harness forms the backbone of the electrical architecture in any vehicle electrical system design.Wire harness is the interconnecting wiring in the vehicle for the transmitting electrical power and signals in the…

AIM: Route the wiring harness on given car hatch and prepare a flatten view in CATIA V5. OBJECTIVE: The objective of  this project is to route the wiring harness and prepare flatten-view drawing for the given car body hatch.All types of packaging rules and constraints have to be considered while routing the harness.Industry…

AIM: To prepare a flattened-view of a previously created harness assembly. OBJECTIVE: The objective of the this project is to create a flattened-view for a harness assembly and then place it on the drawing sheet.it is desired that the bundles with protective coverings are represented with differernt visuals on the drawing…

HOOD DESIGN IN UG NX OBJECTIVE: Design hood outer panel,inner panel and reinforcements with the given outer hood skin,master section and design parameter. INDROUCTION: The hood bonnet is the hinged cover over the engine of motor vehicles.Hood can open to allow access to the engine compartment for maintenance and repair.in…

OBJECTIVE: To study the standard and regulation for the fender design of wheel arch area and then analysis the data which is given in the question wheather the wheel arch area will going to pass the standards or not. There is various standard which normally varies by region and there road structure like japanese,u.s AND…

INTROUCTION: Fender is the American english term for the part of an automobile,motorcycle or other vehicle body that frames a wheel well(the fender underside0.its primary purbose is to prevent the sand,mud,rocks,liquids,and other road spray from being thrown into the air by the rotating tire.Fender are typically rigid…

ROOF DESIGN INDROUCTION: An automobile roof is the portion of an automobile that sits above the passenger compartment, protecting the vehicle occupants from sun, wind, rain, and other external elements. Though it just looks like a styling surface that protects from sun, wind and other elements, various environmental conditions…

SECTION MODULUS Section modulus is termed as the ratio of second moment of area and distance from N.A (Neutral axis) to the extreme fiber. Also it is the measure of strength of given member. The stress in the outermost section of beam is computed with the help of section modulus. It is indicated by S.  Section modulus…

CAR BACK DOOR DESIGN Aim: To design back door of car using given outer class 'A' surface. What is back door of a car? A door which is located at the rear side of a car which gives access for the boot space to store luggage, spare wheel etc. These doors can be operated manually or electric powered. In most of…

                                                        DESIGN AND DRAFT ANALYSIS OF SWITCH BEZEL OBJECTIVE: The objective of the project is to design the swith bezel and to do…

LASTIC DESIGN OF A COIN HOLDER USING CATIA V5 OBJECTIVE To design a coin holder used in automobiles using Catia V5 using a Class-A surface as input and performing draft analysis on the component to ensure manufacturability INTRODUCTION Manufacturing process: Injection Molding Brief about the process It is a manufacturing…

BUMPER DESIGN – CHALLENGE 4 AIM Create the Bumper Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. INTRODUCTION A bumper is a structure…

AIM:To create a switch bezel from the given A-class surface by considering a thickness of 2.5 mm and also creating Core and Cavity blocks for it. PROCEDURE: A class surface : The input of the product designer is in the form of the A-class surface. The job of the product designer is to create the B and C surfaces keeping…

Door Handle Design Given Surface   Tooling axis Creation In injection molding, the Class A surface is first analyzed to determine the axis or tooling direction that separates the molds. Tooling direction is critical for plastic product design because it determines mold direction Steps followed On the extracted surface,…

AIM:- To create the Dog House for the Door Trim. DOG HOUSE:- Dog HOuse is an engineering feature used in plastic trim design.Dog houses are used as supporting feature. The primary function of Dog House is to avoid SINKMARK. DRAFT ANALYSIS:-Draft analysis is required to check if a part has required draft…

AIM: Assemble and apply gd&t to the butterfly valve assembly drawing PROCESS: Step:1 open the assembly platform and add to the butterfly valve sub components.Step:2 The next step assemble to the disc plate and shath used to move quardinates and assymbly constraints.Step:3 After assemble to the body Disc plate and shaftStep:4…