BHARATH KUMAR
Graduate Apprentice Trainee at Nestlé
Skills Acquired at Skill-Lync :
Introduction
12 Projects
Mixing efficiency
…
06 Mar 2021 10:22 AM IST
Steady Vs Unsteady flow over a cylinder
Simulation of flow over a cylinder and visualizing the Karman vortex street Aim: To Simulate the 2D laminar flow…
06 Mar 2021 10:22 AM IST
Ahmed Body Challenge
Aim: To simulate the Ahmed body and to calculate the Coefficient of drag and lift. Introduction : The Ahmed body is a bluff type body that was designed to study the slant angle effect on the cars drag coefficient. It has a simple shape in the entrance region to minimize detachment points in the flow generated…
06 Mar 2021 10:22 AM IST
Exhaust Port Challenge
Aim of the project : To perform Conjugate Heat Transfer(CHT) simulation on an Exhaust port. Introduction : The term Conjugate Heat Transfer (CHT) is used to describe processes that involve simultaneous energy exchange between the solid and fluid domains due to interaction between them. CHT analysis is essential in…
06 Mar 2021 10:22 AM IST
Conjugate Heat Transfer Analysis on a graphics card.
Aim: To Perform a steady-state conjugate heat transfer analysis on a graphics card model. Introduction : The graphics processing unit, or GPU, has become one of the most important types of computing technology, both for personal and business computing. Designed for parallel processing, the GPU is used in a wide range of…
06 Mar 2021 10:23 AM IST
Rayleigh Taylor Instability Challenge
Introduction: Rayleigh–Taylor instability is the instability of an interface between two fluids of different densities which occurs when the lighter fluid is pushing the heavier fluid. Water suspended atop oil is an everyday example of Rayleigh–Taylor instability, and it may be modeled by…
06 Mar 2021 10:22 AM IST
Week 8 - Simulating Cyclone separator with Discrete Phase Modelling
Aim: To perform analysis on cyclone separator and calculate the separation efficiency and pressure drop. Introduction: Cyclone separators are separation devices that use the principle of inertia to remove particulate matter from flue gases. Cyclone separators is one of many air pollution control devices known as…
06 Mar 2021 10:23 AM IST
Week 9 - Parametric study on Gate valve.
Aim: To perform a parametric study on the gate valve simulation by setting the opening from 10% to 80%. Introduction: Gate Valve, also known as a sluice valve, is a valve that opens by lifting a round or rectangular gate or wedge out of the path of the fluid. The distinct feature of a gate valve is the sealing surfaces…
06 Mar 2021 10:23 AM IST
Week 10 - Simulating Combustion of Natural Gas.
Aim: Part 1: To perform a combustion simulation on the combustor model and plot the variation of the mass fraction of the different species in the simulation. Part 2: Adding water content in the fuel and observe the effect of the results. Introduction: Combustion is a high-temperature exothermic redox chemical reaction…
06 Mar 2021 10:23 AM IST
Week 7: Gearbox simulation
Part 1: 20% Immersion, Fluid - Engine oil. 30% Immersion, Fluid- Engine oil. 20% Immersion,Fluid-n-heptane (c7h16). 30% Immersion,Fluid-n-heptane (c7h16). Part 2: What is Dynamic meshing? Give some other examples where dynamic meshing can be used. What is the fluid Sloshing effect? Discuss whether the sloshing effect…
28 Apr 2021 02:56 PM IST
Week 4-1D Element Creation Challenge
Task Mesh the Given component with the Size of 5 Units. Create 1D elements on the following component with given cross-section and DOF a. Rod element:- Translational DOF should be Constrained with RBE2 link Cross-Section: BOX- Dimension a= 12 mm …
17 Aug 2021 12:18 PM IST
Week 6-Meshing of Hood Challenge
Components of the hood to mesh: Inner extract Hinge Latch Outer extract 1. Inner extract Initially, the outer extract geometry was checked for duplicates (Geom – defeatures- duplicates). But there were no duplicates. Next, I went ahead to check for missing surfaces and if there were any missing surfaces it…
05 Sep 2021 05:48 PM IST
1 Course Certificates
13 Workshop Certificates
How to build a world-class amusement park as a Mechanical Engineer
Design Calculations of welded structures as per industry standards
Academic Qualification
B.E
The National Institute of Engineering
01 Jun 2017 - 31 May 2021
12th
Vivekananda Pre-university College Puttur
01 Jun 2015 - 01 May 2017
10th
Vittal Jaycees English Medium School
01 Jun 2014 - 31 May 2015
Here are the courses that I have enrolled
Similar Profiles
Ladder of success cannot be climbed with hands in pocket.
The Future in Motion
Give more than what you get you will get more than what you gave
Avid learner