The Concrete Mix Design for M35 grade concrete with fly ash - Propotoning : Grade :M35 Cement type:OPC 43 grade(IS8112) Mineral admixture:Fly ash Maximum nominal size of aggregate:20mm Maximum cement content:320kg/m^3(Table :5 IS 456-2000,based on exposure condition) Maximum w/c ratio :0.45(table 5,IS 456-2000) Workability:100mm…

Aim of the project :- To sketch a G+1 floor residential plan according to vastu Shastra and to list down the names of the structural drawing required to be provided to site for construction. To assume the size  of structural elements (column,beam, slab etc) and to calculate the load from the members as per IS code.…

AIM:  To Create the geometries from P1 to P2 using all the coordinates system methods and P3 to P10 by any one coordinate system To Draw the profile and the trusses using any coordinate system methods. The dimensions are there for reference.   INTRODUCTION: Before going to the drawing, we should know about the…

Aim: To create a floor plan footing details and isometric view of steps and gabble ball in AutoCad  Introduction AutoCAD is a dropping software that is used to draft drawing in the present keys we are using AutoCAD to create various drawings with his useful tools Part 1: Cross section of load bearing wall over spread…

Aim: Design and draft layout of architecture drawings for a plot size of 60'x 20' ,facing east and develop revelant structural drawings  Introduction: To desire drawing of floor plan elevations and section are sketch in AutoCad using various tools full stop the step by step procedure of drawing is explained in detail with…

Creating the templates Aim: To create the custom1_ titleblock and custom2_ titleblock template using AutoCAD. Introduction: In this project we have to create a template of custom1_ titleblock and custom2_ titleblock using various tools .The template is arranged in the table format that specifies the drawing and which has…

Create the layouts of the Kitchen and provide hatches pattern as shown. Also, use blocks  wherever required. Provide appropriate dimensions in the plan. Assume the size of doors, appliances and others as per the standards. Aim: To create a layout of the kitchen and provide hatch pattern and appropriate dimension as…

Create a layout of the Plan and Section A of the project in Challenges 7, using the template Tutorial-mArch.dwt in a scale as given in the Figure. Use the MV command to create the viewport of the size as shown in Figure. Also, use ATTEDIT command to edit the information in the title block. Use A1 size for the layout. Take…

Create a 3D Furniture element as shown in the Figure. Assume dimensions which are missing. Aim: To create a 3D model of the furniture element as per the given drawing Introduction: 3D modelling in AutoCad includes 3D solids, surfaces, meshes and wireframe objects  Type of 3D model:  There are several types of…

Aim: To create a 3D isometric view of the building with the given plan and elevation  Introduction: Isometric drawing is a form of 3D drawing which is set of using 30 degree angles. It is a type of action matric drawing so that schemes scale is used for every access. Resulting in a non distorted image. Since isometric…

Create 3 dimensional model of the digestive building with rendered view Aim: To create the 3D rendered model of the residential building in AutoCad Introduction: 3D CAD or three dimensional computer assigned design in the technology for design and technique kal documentation which repairs manual drafting with an automatic…

1.1  Write the steps involved to upload a .std file through web mail? Answer:  Open the STAAD. Pro software and locate the share option available on the introduction screen  After clicking on the share button, select send mail option  Then, browse for the Std. file on your machine and send it 1.2 …

  1.1.  How will you assign Circular section to column? Answer : Go to properties in that select define property select circle and select define option  and give the radius for the member and assign the defined circle to the member created    Q1.2.  How will you assign Unit system to a .std…

1.1 State the primary load cases to be considered for design. Answer: The primary load cases that are to be considered for design are listed below: Dead Load (IS 875: Part I). Live Load (IS 875: Part II). Wind Load (IS 875: Part III). Snow Load (IS 875: Part IV). Seismic Load (IS 1893: 2016). 1.2. What is One – Way slab?…

1. Design a multi-storey Residential Building located in Bangalore using STAAD Pro Connect Edition. The specification must be as follows:      Building floors G + 6 + R Plan dimension B = 25m ,  L = 16m Storey Height h = 3.5m Soil  Hard soil Use Residential Purpose Safe Bearing Capacity 180…

What is the mode of failure or damage of the beams in the figure above? Are the damages repairable? Elaborate Q.1 a. This crack will be formed due to the flexural failure of a beam. The flexural strength, known as modulus of rupture, bend strength, or fracture strength, is a material property, defined as the stress in…

1.Differentiate Static analysis and Dynamic analysis with proper representing pictures (30 marks) Answer: Static analysis and dynamic analysis are two distinct approaches used in software testing and security to evaluate the quality and security of a software system. Static analysis refers to the evaluation of software…

  Question 1: Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams). Look into aspects of symmetry, redundancy and bi-directional stiffness and ductility. Answer: Symmetry: Symmetry in the layout is important because…

Question 1:The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional area of the shear walls. Compare the three alternatives, taking into account…

Model a 25-storey building on ETABS with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey height of 3 meters. Given data: Structural Element Sizes:  Beams: 300 × 400 mm  Columns: 800 × 800 mm …

1. Detailed design of concrete buildings -1 Detailed design of beams in Etabs 2018.The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment ResistingFrame. The following challenge deals specifically with two continuous beams in the 1st floor.         1) 3 span continuous…

Reinforcement detailing of columns in Etabs 2018. The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment Resisting Frame. The following challenge deals specifically with two columns at the following grid intersections. 3A 3B Provide details of longitudinal reinforcement for the two columns,…

QUESTION: The Etabs file for a G+6 building is provided. Run the analysis and design the RCC shear walls (show in the etabs model). The following challenge deals specifically with the shear wall of size 300x1500 at grid A-11 in the structural model. Extract values of longitudinal steel ratio, boundary element length and…

Q.1. Design a square footing for a column size of 400x400. The compression axial load for the load combination of (1.5 DL + 1.5 LL) is 2000 KN. The safe soil bearing capacity is 150 KN/m2 at a depth of 2 metres below E.G.L. Participants are free to go for either a tapered or stepped footing. Besides the total axial…

    The architectural drawings for a G+7 residential building in zone 5 has been provided. The floor plan is the same for all 7 floor levels. Possible column positions have also been provided. Conceptualize a framing plan layout and then model the building in Etabs. The following architectural drawings have been…

Model the isolated footing provided in week 11 challenge on SAFE. Analyze and design it to verify the size, depth and steel provided as per calculations. 2. A column of size 600x600 carrying an unfactored gravity load (DL+LL) of 1175 KN is to be supported on pile cap, which ultimately transfers load to the piles underneath.…

Aim: To model and analyse multiple buildings with different floor levels and design perimeter using etabs software and compare the results to understand their overall seismic behaviour  Introduction: The structural configuration of building page of major role in determining the overall response during an earthquake.…

Aim: To carry out modelling analysis design and preparation of construction drawing of G+3 RCC building situated in Guwahati Assam  Introduction: In this project participants will get to experience the entire design process from Modelling and laces design and preparation of the construction drawings. The architectural…

1. Design a Warehouse Building located in Chennai using STAAD Pro Connect Edition. The specification must be as follows:      Width  30m Length 50m Eave Height 9m Bay spacing 6m Soil type Medium Safe Bearing Capacity 200 kN/m2 Roof slope 1 in 12 Assume suitable sections for structural elements. Follow IS800:2007, IS1893…