Objective : To simulate bullet penetrating bucket ,using three different non linear materials for bucket and analyse the behaviour at same velocity of bullet. Geometry : The given geometry was imported in explicit dynamic. Materials used : For Bullet - Explicit material used TANTALUM For Bucket - Non linear material used…

Objective: To perform static structural analysis on sheet metal bending to using three different materialsalong with changing parameters like mesh refinement and coefficient of frictionto find out equivalent stress,equivalent strain and total deformation in y direction. Geometry : Materials used : For sheet metal Aluminium…

objective :               The main objective of the assignment 6 is to simulate the neon frontal crash model and giving the following output requests, Sectional force in the rails at location of indicated node 174247. Axial force received on the rails from bumber. Shotgun cross sectional…

Objective : To perform explicit simulation tom find out equivalent stress,total deformation and user defined result for temperature of machining with planar at two different cutting speeds(20000mm/s;15000mm/s). Geometry : The given geometry was imported in explicit dynamics. Material :   from the enginnering data,…

OBJECTIVE:             In this assignment , we need to meshing for bumber and we need to connect the bumber parts by using conectors and we need to run the 6 simulations for crash tube with recommended settings and we need to compare the cases os of different interface settings and different…

Objective: To create different types of 1D elements of with given cross section. Procedure: 1. A new file in Opti struct format was opened in Hypermesh, parallel bracket geometrywas imported.2. The plates were checked for thickness and their midsurfaces were extracted and savedto two different components.3. Washer split…

Grid dependency test :  Grid dependency test also called as mesh covergence test.  A mesh convergence test should mean computing the solution on successively finer      grids. The difference between two refinements is usually taken as a measure of the accuracy of the coarser of the two. Grid convergence…

objective :              The main objective of the assignment 6 is to simulate the neon side crash model and giving the following output requests, Sectional force in the cross member. Intrusion at B pillar,hinge pillar and fuel tank region.Provide recommendation…

Objective :       To perform static structural analysis on welding joints using three different materials and to compare the results like directional deformation,stress generated on welded joints and strain developed. Geometry : The given geometry was imported.  Weld materials :   Stainless steel…

Objectives:   Check the material properties of the rail component and calculate the speed of sound in steel rail.Calculate the time taken for a stock wave to travel from one end of the rail to other end. Edit the engine file, so that the stress wave can be monitored. Set the frequency of  animation output to…

Objective :  Objective of this challenge is Comparing the results which is Equivalent stress, Total deformation and Stress intensity obtained by using three different materials for spur gears. spur gear :The most common type of gear is the spur gear. These gears have straight teeth and must be mounted on parallel…

Objective : Perform an analysis to simulate the bending of a wire using 3 different types of materials for the wire to find out equivalent stress and equivalent strain developed. Geometry :   The given geometry was imported in static strutural. Material :       By using three general non linear…

Objective :  perform a transient structural analysis on a worm gear assembly to get results for Equivalent stress, Equivalent elastic strain and the total deformation in the model. Geometry : The given model is imported in transient structure and The model is edited due to the acadamic limit. Material :    …

Objective: To batch mesh the given components with the given criteria and assign the non-linear material property Steel to them.Procedure:1. A new file was opened in Hypermesh, the hood model was imported2. All the solids were deleted from the component, Batch meshing was done accordingto the given criteria and parameters…

Objective: To mesh the hood of a car according to the quality criteria given Procedure:1. A new Opti struct file was opened in Hypermesh, hood geometry was imported, allthe solids were deleted from the component.2. Separate mid surfaces were created for the all the components, the mid surfaces werechecked for defects and…

GAS TANK : https://drive.google.com/open?id=1erHckdKk4sLjDOKAEKS787rR-hrpDLWq ASSEMBLY : https://drive.google.com/open?id=1nScB5H60blJdz_v8862JURNqbM05HH8N  

Understanding the utility of project curves feature and revolved cut feature in solidworks. FRONT FORK: https://drive.google.com/open?id=1nIhSoczTzlPF2DXL4hw-Bn-W6WciDOTL REAR WHEEL: https://drive.google.com/open?id=1VZ1l6XHMCsRFatCfupgyLWk_rsi2nJe5    

Objective1: To create Tetra mesh for Housing model according to given element criteria Criteria: Elements sizes: Min- 2mm, Target- 5mm, Max- 7mm, Tet collapse: 0.15 Procedure:1. A new Opti struct format file was opened in Hypermesh, housing CAD model wasimported.2. First all the solids were deleted from the parts, then…

Objectives : Comparing the result values by increasing the bearing load 5 times.      Comparing the user defined result of total deformation with the inbuilt result by ANSYS. Importing Geometry : The given geometry is imported in structural anlysis. Material : For this simulation the default material which…

Objective: To Join a given frame assembly using different types of connectors in the givenorderProcedure:1. A new radios format file was opened in Hypermesh. The frame assembly wasimported2. All the 12 surfaces were meshed with quad element type.3. The 2 or 3 surfaces were connected using the specified connectors according…

Objective  :                   Perform a transient structural analysis on a double universal joint with a spring using three different materials, to obtain the Equivalent stress and total deformation for all the three cases and compare results. Geometry : The given geometry…

Objective :  To perform a static structural analysis of sphere pressing on a plateAnd to find out its plastic deformation. Geometry : Given geometry is imported in static structural. Materials :   Structural steel - sphere   Structural steel NL - plate Symmetry : The original geometry is shown in figure. …

Objective : To perform transient analysis on piston and cam mechanism to find out  the Equivalent Stress, Directional Deformation and Equivalent Elastic Strain with Friction-less contact, Frictional with 0.1 and 0.2 as the frictional contact, compare results,inference the varying results. Geometry : The given geometry…

Objective :  Perform a parametric study using 3 different values of thickness for the car body, to find out the total deformation and Equivalent stresses acting on the model. Geometry : The given geometry was imported in explicit dynamic. Materials used : For car body - Stainless steel NL for rigid body - Structural…

In this Excercise we will be performing Mesh Cleanup on 2D SHELL Elements:   Objective:   To performing geometry cleanup operation by given models, 1. Practice2. Mounting Bracket3. Clip Repair.   And extract the mid surface and clean mid surface geometry and create the 2D mesh with given target element length.…

Objective : To perform a rolling operation on copper work-piece and to evaluate the results of Equivalent stress for the whole setup,Equivalent Plastic strain for the work-piece,Directional Deformation in the Z axis for the work-piece. Geometry :  The given geometry was imported in static structural and lenth of the…

Objective :  To perform the tension test and torsion on the specimen provided,to find out the total deformation, equivalent stress and temperature of the specimen. Geometry : The given geometry was imported in explicit dynamics. Material :  From the engineering data, the explicit material is taken which is …

Objective:        Objective of this challage is static structural analysis on a plate with single hole and multiple holes.and also we need to select in automotive industry piont of view, which design is good for ananlysis and manufacturing and we need to give reason. Case :1 Stress concentration of…

  OBJECTIVE: CASE 1: To perform static structural analysis on iphone bending as it shown in the video. CASE 2: Move the bottom fingers from their defined position to the given position X= 22.5mm & Z= 10mm and obtain the results for the simulation. Also define the S-N curve for the Aluminium Alloy material as per…

Aim:    To write a python code for the otto cycle and we need to create a P-V diagram for the otto cycle. And also we need to find thermal efficiency. Otto cycle process & formulae : The processes are described by Process 0–1 a mass of air is drawn into piston/cylinder arrangement at constant pressure.…

Objective:   Write a program to simulate the transient behavior of a simple pendulum and to create an animation of its motion. Theory: In mathematics, an Ordinary Differential Equation (ODE) is a differential equation containing one or more functions of one independent variable and the derivatives of those functions.…

1.What does popt and pcov mean?   popt is an array with the optimal parameters obtained using a non-linear least squaresfit.   pcov is a 2d array with the estimated covariance of the parameters in    popt. 2.What does np.array(temperature) do?   A numpy array is a grid of values, all of the same type.Here it is being used…

OBJECTIVE: Import the CAD geometry of car hood assembly Clean up the geometry  Extract Mid-Surface for the geometry Mesh geometry with given quality criteria   Hood: Hood parts: 1.Inner part 2.Outer part 3.hinge 4.latch   METHODOLOGY Import the CAD Geometry and do Geometry clean-up with no topological…

OBJECTIVE The bottle Cap component is given with various thicknesses in threads, teeth, and ribs. Taking manual mid surface with different procedures and meshing the component with 1mm target element size and mentioned quality parameters. Bottele cap: S.No Quality Criteria Value 1 Target/Average Length …

This tool test was completed within a time you gave. 

Objective: For the given component, check for the geometrical errors and mesh with the given element Quality criteria. Use tetra elements to model the component and there should not and kinks and dips on the surface of the component. Write a detailed report on your meshing process. S. No  Quality Criteria …

This tool test is completed within a time you gave.

Objective : In this challenge ANSA pre-processor is used to morph the given geometry using the required tools. It is basically changing the shape of the model without changing the numerical values. Transforming the whole shape will take lot of time and effort whereas through morphing changing the shape will be quick and…

Objective : The rear door model is given for the connections using different types of 1D connections whichever suitable and makes the proper connections and attaches the FE model to give a model for the simulation process. connector :  Connectors are a geometric representation of connections between entities. The…