Engineering Mechanics cover
Interactive book · Semester 1-3

Engineering Mechanics

Resolve forces, solve a truss joint by joint, push a block up a rough slope, find a section's centroid and moment of inertia, launch a projectile and collide two balls

22 chapters, 24 interactives, few words. Every chapter is mapped to the Anna University, VTU, SPPU, Mumbai University and KTU units it covers: forces and vectors, concurrent forces and Lami's theorem, forces in space, moments and couples, resultants, beam reactions, equilibrium in three dimensions, trusses, frames and cables, friction on slopes, ladders, wedges and belts, centroids, Pappus-Guldinus, area and mass moments of inertia, rectilinear and curvilinear motion, Newton's second law and D'Alembert's principle, work and energy, impulse, momentum and impact, and rigid-body rotation with the instantaneous centre.

  • AUME3351Engineering Mechanics
  • VTUBCIVC103Engineering Mechanics
  • SPPU101011Engineering Mechanics
  • MUFEC104Engineering Mechanics
  • KTUGCEST103Engineering Mechanics

By Skill-Lync · Updated 17 Nov 2026 · 22 chapters · 24 interactives · free, no sign-up

Chapter 1

Forces, units and vectors

Which syllabus covers thisAU ME3351 Unit IVTU BCIVC103 Module 1SPPU 101011 Unit IMU FEC104 Module 1KTU GCEST103 Module 1

What is engineering mechanics, and how are statics and dynamics different?

Engineering mechanics applies Newton's laws to the bodies engineers build. Statics studies bodies at rest or moving at constant velocity, where the forces balance: the reactions under a bridge, the tension in a crane cable. Dynamics studies bodies that accelerate: kinematics describes the motion, kinetics links it to the forces. Two idealisations make problems solvable: a particle (all mass at a point, size ignored) and a rigid body (it never deforms). Strength of materials later drops the rigid-body assumption.

Which units and laws does the subject rest on?

SI units: length in metres, mass in kilograms, time in seconds, and force in newtons, where 1 N accelerates 1 kg at 1 m/s². Weight is W = mg with g = 9.81 m/s², so a 1 kg mass weighs 9.81 N (the old 1 kgf). Newton's three laws carry everything: a body stays at rest or in uniform motion unless a net force acts, F = ma, and action equals reaction. Newton's law of gravitation explains g. Keep units consistent and check them at the end of every answer.

Why is force a vector, and what do the parallelogram and triangle laws say?

A force has a size, a direction and a point of application, so it adds like a vector, not like a number. The parallelogram law: draw two forces from one point as adjacent sides of a parallelogram, and the diagonal from that point is their resultant. The triangle law is the same thing drawn head to tail: the closing side is the resultant. Two 60 N and 45 N forces at right angles give 75 N, not 105 N. Try it: change the angle between P and Q and watch R swing between P − Q and P + Q.

Resolve and add forces: rectangular components, the parallelogram and triangle laws, and the resultant's size and direction: interactive loads as you scroll

How do you resolve a force into rectangular components?

Split it along perpendicular x and y axes: F_x = F cos θ and F_y = F sin θ, with θ measured from the x axis. In vector form F = F_x i + F_y j, where i and j are unit vectors (length 1) along x and y. Components make adding many forces easy: add all the x parts, add all the y parts, then R = √(ΣF_x² + ΣF_y²) at tan⁻¹(ΣF_y / ΣF_x). For a force along a line, multiply its size by the line's unit vector, its direction divided by its length.

How are force systems classified, and what is the principle of transmissibility?

By where the forces lie and meet. Coplanar forces lie in one plane; non-coplanar (space) forces do not. Concurrent forces pass through one point, parallel forces never meet, and a general system is neither. Collinear forces share one line. The principle of transmissibility says a force on a rigid body can slide anywhere along its own line of action without changing the body's equilibrium or motion: pushing a car from behind or pulling it from the front along the same line has the same external effect. It does change internal stresses, which is why it applies to rigid bodies only.

Predict, then check

Two forces of 10 N each act at one point. At what angle between them is their resultant also 10 N?

Worked examples

Resultant of two forces at a point · P = 60 N at 20° and Q = 45 N at 110° to the x axis (the interactive's starting values)
  1. ΣF_x = 60 cos 20° + 45 cos 110° = 56.382 − 15.391 = 40.991 N
  2. ΣF_y = 60 sin 20° + 45 sin 110° = 20.521 + 42.286 = 62.807 N
  3. R = √(40.991² + 62.807²) = 75.00 N; the forces are 90° apart, so √(60² + 45²) = 75 N agrees
  4. Direction: tan⁻¹(62.807 / 40.991) = 56.87° from the x axis

Answer: R = 75 N at 56.87° to the x axis

A force along a line, in unit-vector form · A 250 N rope pull from point A (0, 0) toward point B (4 m, 3 m)
  1. Direction AB = 4i + 3j m, length √(4² + 3²) = 5 m
  2. Unit vector λ = (4i + 3j) / 5 = 0.8i + 0.6j
  3. F = 250 λ = 200i + 150j N
  4. Check: √(200² + 150²) = 250 N

Answer: F = 200 i + 150 j N

Resultant of four concurrent forces · 200 N at 0°, 150 N at 60°, 100 N at 150° and 120 N at 240°, all through one point
  1. ΣF_x = 200 + 150 cos 60° + 100 cos 150° + 120 cos 240° = 200 + 75 − 86.60 − 60 = 128.40 N
  2. ΣF_y = 0 + 150 sin 60° + 100 sin 150° + 120 sin 240° = 129.90 + 50 − 103.92 = 75.98 N
  3. R = √(128.40² + 75.98²) = 149.19 N
  4. θ = tan⁻¹(75.98 / 128.40) = 30.62°

Answer: R = 149.2 N at 30.6° to the x axis

Chapter 2

Concurrent forces, free-body diagrams and Lami's theorem

Which syllabus covers thisAU ME3351 Unit IVTU BCIVC103 Module 2SPPU 101011 Unit IIIMU FEC104 Module 2KTU GCEST103 Module 1

What is a free-body diagram, and how do you draw one?

A free-body diagram isolates one body (or one joint or knot) and shows every external force on it, and nothing else. Draw the body alone, then add its weight at the centre of gravity, every contact force (normal to a smooth surface), cable tensions pulling away along the cable, and support reactions. Unknown directions get assumed senses; a negative answer just means the sense was the other way. Most wrong answers in mechanics come from a missing or extra force on this sketch, so draw it before writing any equation.

When is a particle in equilibrium?

When the resultant of all forces on it is zero: ΣF_x = 0 and ΣF_y = 0 in a plane. That is two equations, so a particle problem in a plane can find two unknowns, such as two cable tensions. Graphically, the forces drawn head to tail close into a polygon with no gap. With three forces the polygon is a triangle, and the three forces must be concurrent: if two lines of action meet at a point, the third must pass through it too.

What does Lami's theorem say?

If three concurrent forces hold a particle in equilibrium, each force is proportional to the sine of the angle between the other two. It is the sine rule applied to the closed force triangle. It works only for exactly three forces, and the angles are the ones between the forces themselves, not to the horizontal. Slide the cable angles down toward flat and watch the tensions climb: two 10° cables holding 1,000 N each carry about 2,900 N, which is why a washing line can never be pulled straight.

A weight hung from two cables: tensions by Lami's theorem, and why they explode as the cables flatten: interactive loads as you scroll

How are spheres and cylinders resting on surfaces handled?

A smooth contact can only push, and only at right angles to the surfaces in contact, so for a sphere or cylinder every contact force points through its centre. A ball in a V-groove, a roller held on a slope by a string, or two pipes stacked in a trench are therefore concurrent-force problems at the centre. Draw one free-body diagram per body, use the shared contact force with opposite senses on the two bodies (action and reaction), and solve the lower body after the upper one.

Predict, then check

A 200 N picture hangs from one wire over a nail, each half of the wire at 10° above the horizontal. The wire tension is about:

Worked examples

A weight hung from two cables (Lami's theorem) · W = 1,000 N; left cable at 30° and right cable at 45° above the horizontal
  1. Angles between forces: T1 and W: 90° + 30° = 120°; T2 and W: 90° + 45° = 135°; T1 and T2: 180° − 75° = 105°
  2. Lami: T1 / sin 135° = T2 / sin 120° = 1,000 / sin 105° = 1035.28 N
  3. T1 = 1035.28 × sin 135° = 732.05 N
  4. T2 = 1035.28 × sin 120° = 896.58 N
  5. Check ΣF_x: −732.05 cos 30° + 896.58 cos 45° = 0

Answer: T1 = 732.1 N, T2 = 896.6 N

A ball on a smooth slope held by a horizontal string · W = 500 N, smooth plane at 30° to the horizontal, string horizontal
  1. Forces on the ball: W down, T horizontal toward the slope, N normal to the slope (at 30° to the vertical)
  2. ΣF_y: N cos 30° = 500, so N = 500 / cos 30°
  3. ΣF_x: N sin 30° = T, so T = 500 tan 30°
  4. N = 577.35 N, T = 288.68 N

Answer: String tension 288.7 N, slope reaction 577.4 N

A lamp on two wires of unequal length · A 150 N lamp hangs from wires 3 m and 4 m long tied to ceiling points 5 m apart
  1. 3-4-5 triangle: the wires meet at 90°
  2. 3 m wire: cos a = 3/5, a = 53.13° above the horizontal; 4 m wire: b = 36.87°
  3. Lami with a + b = 90°: T_3 = W cos b / sin 90° = 150 × 0.8
  4. T_3 = 120 N, T_4 = 150 × 0.6 = 90 N
  5. The shorter, steeper wire carries more

Answer: 120 N in the 3 m wire, 90 N in the 4 m wire

Chapter 3

Forces in space and equilibrium of a particle

Which syllabus covers thisAU ME3351 Unit IVTU not in syllabusSPPU 101011 Unit IIIMU FEC104 Module 1KTU GCEST103 Module 1

How is a force in space described?

By three rectangular components, F = F_x i + F_y j + F_z k, with magnitude √(F_x² + F_y² + F_z²). The angles θ_x, θ_y, θ_z between the force and the three axes give its direction cosines: cos θ_x = F_x / F and so on. Only two of them are independent, because cos²θ_x + cos²θ_y + cos²θ_z = 1. A force of 300i − 400j + 1,200k N has magnitude 1,300 N and makes 22.6° with the z axis.

How do you write a force that acts along a line between two points?

Cables, struts and guy wires give a force's direction as two points, not angles. Take the position vector from the first point to the second, r_AB = (x_B − x_A) i + (y_B − y_A) j + (z_B − z_A) k, divide by its length to get the unit vector λ_AB, and multiply by the force's size. The components then come out with the right signs automatically, which avoids most of the sign slips that angle-based resolution invites in three dimensions.

How do you add concurrent forces in space?

Exactly as in a plane, with one more component: add all the x components, all the y components and all the z components. R = √(ΣF_x² + ΣF_y² + ΣF_z²), and its direction cosines are ΣF_x / R, ΣF_y / R and ΣF_z / R. Writing every force as magnitude times unit vector first keeps the bookkeeping clean. Mumbai University's first module asks for this resultant of space forces before any equilibrium.

How is a particle held in equilibrium in space?

ΣF = 0 now means three scalar equations, ΣF_x = 0, ΣF_y = 0 and ΣF_z = 0, so three unknowns can be found, for example three cable tensions. Write each tension as T times its unit vector toward its anchor, add the weight, and solve the 3 × 3 system. A cable can only pull: if the solution gives a negative tension, that cable would have to push and goes slack. Move the load outside the anchor triangle and watch it happen; lower it and every tension falls as the cables turn vertical.

A load hung from three cables in space: direction cosines, unit vectors and the three tensions from ΣF = 0: interactive loads as you scroll
Predict, then check

A load hangs from three ceiling cables. If you lower it to twice the depth, the cable tensions:

Worked examples

Magnitude and direction cosines · F = 300 i − 400 j + 1,200 k N
  1. F = √(300² + 400² + 1,200²) = 1,300 N
  2. cos θ_x = 300 / 1,300 = 0.2308, θ_x = 76.66°
  3. cos θ_y = −400 / 1,300 = -0.3077, θ_y = 107.92°
  4. cos θ_z = 1,200 / 1,300 = 0.9231, θ_z = 22.62°
  5. Check: 0.0533 + 0.0947 + 0.8521 = 1

Answer: 1,300 N; θ_x = 76.7°, θ_y = 107.9°, θ_z = 22.6°

Guy cable force in components · A 1.5 kN cable runs from the top of a mast A (0, 0, 12 m) to a ground anchor B (4, −3, 0) m
  1. r_AB = 4i − 3j − 12k m, length √(16 + 9 + 144) = 13 m
  2. λ_AB = (4i − 3j − 12k) / 13
  3. F = 1,500 λ_AB = 461.5 i − 346.2 j − 1384.6 k N
  4. The mast is pulled down by 1385 N and sideways by √(461.5² + -346.2²) = 577 N

Answer: F = 461.5 i − 346.2 j − 1384.6 k N

A load hung from three cables · W = 1,200 N at P (0, 0, −1.6 m); anchors A (−1.5, 1, 0), B (1.5, 1, 0), C (0, −1.8, 0) m
  1. Lengths: PA = PB = √(1.5² + 1² + 1.6²) = 2.4104 m, PC = √(1.8² + 1.6²) = 2.4083 m
  2. Unit vectors: u_A = (-0.6223, 0.4149, 0.6638), u_B = (0.6223, 0.4149, 0.6638), u_C = (0.0000, -0.7474, 0.6644)
  3. ΣF_x = 0 gives T_A = T_B (symmetry); ΣF_y = 0 and ΣF_z = 0 then give T_A and T_C
  4. T_A = T_B = 581.1 N, T_C = 645.1 N

Answer: T_A = T_B = 581 N, T_C = 645 N

Chapter 4

Moments, Varignon's theorem and couples

Which syllabus covers thisAU ME3351 Unit IIVTU BCIVC103 Module 1SPPU 101011 Unit IMU FEC104 Module 1KTU GCEST103 Module 1

What is the moment of a force about a point?

Its turning effect: M = F × d, the force times the perpendicular distance from the point to the force's line of action. Units are N·m. The sense matters, so pick a convention (here counter-clockwise positive) and stick to it. Push a door at the handle and it swings easily; push near the hinge and nothing happens, because d is tiny. Change the angle between the force and the spanner: only the part of r perpendicular to the force counts, so a pull along the handle gives no moment at all.

Moment of a spanner force about a bolt: force × perpendicular distance, the same answer from components (Varignon), and the equivalent couple: interactive loads as you scroll

What is Varignon's theorem, and why is it useful?

The moment of a force about a point equals the sum of the moments of its components about the same point. In two dimensions that gives M_O = x F_y − y F_x, with no perpendicular distance to find: resolve the force at any point on its line of action, take each component times its own lever arm, and add. It is also why a resultant can be located: the resultant's moment must equal the sum of the moments of the forces it replaces.

How are moments written with vectors, and what is the moment about an axis?

In three dimensions the moment about point O is the vector product M_O = r × F, where r runs from O to any point on the force's line. Its direction is the axis the force tends to turn about (right-hand rule) and its size is F d. The moment about an axis through O with unit vector λ is the projection λ · (r × F), the mixed triple product, a 3 × 3 determinant. The scalar product P · Q = PQ cos θ gives the angle between two vectors or the component of one along the other.

What is a couple?

Two equal, opposite, parallel forces that do not share a line. Their resultant force is zero, but they turn: the moment is F × d, where d is the distance between them, and it is the same about every point in the plane. That is the difference from a single force, whose moment depends on the point. Couples with the same moment and sense are equivalent whatever their forces and spacing: 100 N at 0.2 m equals 400 N at 0.05 m. Couples add as plain numbers in a plane, as vectors in space.

Predict, then check

You pull a spanner at the same point, first at 90° to the handle, then at 45°. The moment at 45° is:

Worked examples

Moment of a spanner pull · F = 200 N applied 0.25 m from the bolt, at 70° to the handle
  1. Perpendicular distance d⊥ = 0.25 sin 70° = 0.2349 m
  2. M = F d⊥ = 200 × 0.2349 = 46.98 N·m
  3. At 90° it would be 200 × 0.25 = 50 N·m; at 70° you keep sin 70° = 0.940 of it

Answer: M = 47.0 N·m counter-clockwise

Moment by Varignon's theorem · A 500 N force at 30° to the x axis acts through the point (2 m, 3 m); find its moment about O
  1. F_x = 500 cos 30° = 433.01 N, F_y = 500 sin 30° = 250 N
  2. M_O = x F_y − y F_x = 2 × 250 − 3 × 433.01 = -799.04 N·m
  3. Negative = clockwise; the line of action is |M| / F = 1.5981 m from O

Answer: M_O = 799.0 N·m clockwise

Moment about an axis (mixed triple product) · F = 100i + 200j − 150k N acts at r = 2i + j + 3k m; axis through O along λ = 0.6i + 0.8j
  1. M_O = r × F = (1 × (−150) − 3 × 200) i + (3 × 100 − 2 × (−150)) j + (2 × 200 − 1 × 100) k
  2. M_O = -750 i + 600 j + 300 k N·m
  3. M_λ = λ · M_O = 0.6 × (-750) + 0.8 × 600 + 0 = 30 N·m
  4. The large moment about O is almost perpendicular to this axis, so little of it turns the body about the axis

Answer: M_O = (-750, 600, 300) N·m; about the axis 30 N·m

Chapter 5

Force-couple systems and resultants

Which syllabus covers thisAU ME3351 Unit IIVTU BCIVC103 Module 1SPPU 101011 Unit IMU FEC104 Module 1KTU GCEST103 Module 1

How can a force be moved to another point?

Not by just sliding it sideways, because that changes its turning effect. Add two equal and opposite copies of the force at the new point B: one copy plus the original form a couple of moment F × d. So a force at A equals the same force at B plus a couple M = F d (in vectors, M = r_BA × F). A hand pushing on the end of a spanner is, at the bolt, a sideways push plus a twist; that is why bolts and shafts are checked for both.

How do you find the resultant of parallel forces?

Add them with signs for the size, R = ΣF, and use Varignon's theorem for the position: R × x̄ = Σ F x, so x̄ = Σ F x / Σ F. Forces in opposite directions can give a resultant outside the span. If ΣF = 0 but Σ F x is not, there is no single resultant: the system is a pure couple. Drag the loads and watch x̄ and the force-couple at A change, including the case where an upward load moves x̄ off the beam.

Resultant of parallel forces and a distributed load on a beam: magnitude, where it acts, and the force-couple system at a point: interactive loads as you scroll

How is a distributed load replaced by a single force?

Its resultant equals the area of the load diagram and acts through that area's centroid. A uniformly distributed load of w kN/m over a length L becomes w L at L/2. A triangular (uniformly varying) load rising from zero to w becomes w L / 2 at 2L/3 from the zero end, one third from the heavy end. A trapezium splits into a rectangle and a triangle. The replacement is valid for finding reactions, not for internal shear and bending inside the loaded length.

How is a general coplanar force system reduced?

Find R_x = ΣF_x, R_y = ΣF_y and the moment about a convenient point O, M_O = Σ(x F_y − y F_x). The system equals R at O plus the couple M_O. If R is not zero, slide R sideways until its moment about O equals M_O: its line of action crosses the x axis at x = M_O / R_y. If R = 0 and M_O is not, the system is a couple; if both are zero, the body is in equilibrium.

Predict, then check

A beam carries 10 kN at 1 m and 30 kN at 5 m from its left end. Their resultant acts at:

Worked examples

Resultant of point loads and a UDL · 6 m beam: 10 kN at 1 m, 15 kN at 2.5 m and 4 kN/m from 3 m to 6 m (all downward)
  1. UDL → 4 × 3 = 12 kN at 4.5 m
  2. R = 10 + 15 + 12 = 37 kN
  3. Σ F x about A = 10 × 1 + 15 × 2.5 + 12 × 4.5 = 101.5 kN·m
  4. x̄ = 101.5 / 37 = 2.743 m
  5. Force-couple at A: 37 kN down plus 101.5 kN·m clockwise

Answer: R = 37 kN down at 2.74 m from A

A triangular load plus a point load · Load rising linearly from 0 at A to 6 kN/m at 4.5 m, plus 8 kN at 1 m
  1. Triangle: ½ × 6 × 4.5 = 13.5 kN at ⅔ × 4.5 = 3.0 m from A
  2. R = 13.5 + 8 = 21.5 kN
  3. Σ F x = 8 × 1 + 13.5 × 3.0 = 48.5 kN·m
  4. x̄ = 48.5 / 21.5 = 2.256 m

Answer: R = 21.5 kN at 2.26 m from A

Reducing a general force system · A 2 m × 1 m bracket: 400 N along +x at O (0, 0), 300 N along +y at (2, 0), 250 N along −x at (2, 1) m
  1. R_x = 400 − 250 = 150 N, R_y = 300 N
  2. R = √(150² + 300²) = 335.4 N at 63.43°
  3. M_O = Σ(x F_y − y F_x) = 2 × 300 − 1 × (−250) = 850 N·m counter-clockwise
  4. Single resultant: crosses the x axis at x = M_O / R_y = 850 / 300 = 2.833 m

Answer: R = 335 N at 63.4°, acting through (2.83 m, 0); or R at O plus 850 N·m

Chapter 6

Supports, free-body diagrams and beam reactions

Which syllabus covers thisAU ME3351 Unit IIVTU BCIVC103 Module 2SPPU 101011 Unit IIIMU FEC104 Module 2KTU GCEST103 Module 1

What reactions does each type of support give?

A support pushes back in every direction it stops the body moving. A roller or smooth surface stops motion in one direction only: one reaction, normal to the surface. A link or cable gives one force along itself. A pin or hinge stops both translations: two components, R_x and R_y. A fixed (built-in) support also stops rotation: R_x, R_y and a moment M. Counting these unknowns before solving tells you whether the three equilibrium equations are enough.

Which equations hold a rigid body in planar equilibrium?

Three: ΣF_x = 0, ΣF_y = 0 and ΣM = 0 about any point. So three unknown reactions can be found, and the structure is statically determinate. Take moments about a support where two unknowns act, so only one unknown is left in the equation. Use the third equation as a check, or take moments about the other support instead of summing forces: an arithmetic slip then shows up as a mismatch.

How do you find the reactions of a beam?

Draw the free-body diagram, replace each distributed load by its resultant, take moments about one support for the other reaction, then sum vertical forces. A simply supported beam has a pin and a roller; an overhanging beam extends past a support; a cantilever is fixed at one end and gets a force and a wall moment. Slide the point load onto the overhang and watch R_A turn negative: that support must hold the beam down. An applied couple changes the reactions but not their sum.

Beam support reactions: simply supported, overhanging and cantilever beams with a point load, a UDL and a couple: interactive loads as you scroll

What are two-force and three-force members?

A two-force member has forces at only two points and no load in between, like a straight link pinned at both ends. For equilibrium the two forces must be equal, opposite and along the line joining the pins, so its direction is known before solving. A body acted on by three forces in equilibrium must have them concurrent (or all parallel). Spotting these saves unknowns: a ladder resting on a smooth wall and rough floor is a three-force body.

Predict, then check

A 6 m simply supported beam carries 12 kN at 2 m from support A. The reaction at A is:

Worked examples

Simply supported beam with a point load and a UDL · Span 6 m; 12 kN at 2 m from A; 2 kN/m over the whole span
  1. UDL → 12 kN at 3 m
  2. ΣM_A = 0: R_B × 6 = 12 × 2 + 12 × 3 = 60
  3. R_B = 10 kN
  4. ΣF_y = 0: R_A = 24 − 10 = 14 kN
  5. Check ΣM_B: 14 × 6 = 84 = 12 × 4 + 12 × 3

Answer: R_A = 14 kN, R_B = 10 kN

Overhanging beam with a load at the tip · 6 m beam on supports at 0 and 4.5 m; 10 kN at the free end (6 m) and 2 kN/m over the full length
  1. UDL → 12 kN at 3 m
  2. ΣM_A = 0: R_B × 4.5 = 10 × 6 + 12 × 3 = 96, R_B = 21.333 kN
  3. ΣF_y = 0: R_A = 22 − 21.333 = 0.667 kN
  4. The tip load nearly lifts A: move it any heavier and R_A turns negative

Answer: R_A = 0.67 kN, R_B = 21.33 kN

Cantilever with a couple · 6 m cantilever fixed at A; 12 kN at 2 m, 2 kN/m over the span, and an 8 kN·m counter-clockwise couple at 3 m
  1. ΣF_y = 0: R_A = 12 + 12 = 24 kN
  2. ΣM_A = 0: M_A − 12 × 2 − 12 × 3 + 8 = 0
  3. M_A = 24 + 36 − 8 = 52 kN·m counter-clockwise (the wall resists the loads' clockwise turning)
  4. The couple does not change R_A: a couple has no resultant force

Answer: R_A = 24 kN up, wall moment 52 kN·m

Chapter 7

Equilibrium of rigid bodies in three dimensions

Which syllabus covers thisAU ME3351 Unit IIVTU not in syllabusSPPU 101011 Unit IIIMU not in syllabusKTU GCEST103 Module 1

What are the equilibrium equations in three dimensions?

ΣF = 0 and ΣM_O = 0 as vectors, which is six scalar equations: forces along x, y and z, and moments about the x, y and z axes. So up to six unknown reactions can be found. Special cases need fewer: concurrent forces in space have no moment equations (three equations), and parallel forces along z need only ΣF_z, ΣM_x and ΣM_y (three equations). Taking moments about an axis that passes through several unknown reactions removes them all from that equation.

What reactions do supports give in three dimensions?

Again, one reaction per blocked motion. A ball on a smooth surface or a cable: one force. A ball-and-socket joint: three force components, no moments. A single bearing or hinge: forces across its axis and, if it is the only support, couples about the cross axes; two aligned hinges are usually modelled with forces only. A fixed support: three forces and three moments. Count them before writing equations: more than six unknowns and the body is statically indeterminate.

How is a plate on three legs solved?

All forces are vertical, so three equations remain: ΣF_z = 0 and moments about the x and y axes. Three legs, three unknowns. Each leg's share of a load is set by where the load sits inside the leg triangle: at the centroid each leg takes a third, at a leg that leg takes everything. Push the load outside the triangle and the far leg's reaction turns negative; a real leg cannot pull, so the plate tips about the opposite edge.

A plate on three legs: leg reactions from parallel forces in space, and the tipping line when the load leaves the triangle: interactive loads as you scroll

Why take moments about an axis instead of a point?

In three dimensions a hinge or a pair of bearings carries several unknown components along its line. Every one of them has zero moment about that line, because they all pass through it. So ΣM about the hinge axis gives one equation with only the remaining unknown, often a cable tension or a prop force. Use M_axis = λ · (r × F) for each force, or, when the axis is a coordinate axis, just the matching component of r × F.

Predict, then check

A load sits exactly at the centroid of the triangle formed by a table's three legs. Each leg carries:

Worked examples

Plate on three legs · Legs at (0, 0), (1.2, 0), (0.6, 1.0) m; plate 200 N at the triangle's centroid; load 600 N at (0.5, 0.35) m
  1. ΣF_z: R1 + R2 + R3 = 800 N
  2. ΣM_y: 1.2 R2 + 0.6 R3 = 600 × 0.5 + 200 × 0.6 = 420 N·m
  3. ΣM_x: 1.0 R3 = 600 × 0.35 + 200 × 0.3333 = 276.67 N·m, so R3 = 276.67 N
  4. Then R2 = (420 − 0.6 × 276.67) / 1.2 = 211.67 N and R1 = 311.67 N

Answer: R1 = 311.7 N, R2 = 211.7 N, R3 = 276.7 N

Round table on three legs · Table 150 N, legs equally spaced on a 0.5 m radius; 300 N placed 0.25 m from the centre toward leg 1
  1. Self-weight at the centre: 50 N per leg
  2. The load is on the line from leg 1 through the centre; leg 1's share rises linearly from 1/3 at the centre to 1 at the leg
  3. Share of leg 1 = 1/3 + (2/3)(0.25 / 0.5) = 2/3, legs 2 and 3: 1/6 each
  4. R1 = 300 × 2/3 + 50 = 250 N, R2 = R3 = 300 × 1/6 + 50 = 100 N
  5. Check: 250 + 100 + 100 = 450 N

Answer: R1 = 250 N, R2 = R3 = 100 N

A hinged hatch held by a cable (moments about an axis) · 1.2 m × 0.8 m hatch, 300 N, hinged along the x axis and held horizontal by a cable from corner C (1.2, 0.8, 0) to D (0, 0.8, 1.0) m
  1. Cable direction CD = −1.2i + 1.0k, length 1.5620 m, so T_z = T × 1.0 / 1.5620
  2. ΣM about the hinge (x axis): the hinge forces drop out; T_z × 0.8 = 300 × 0.4
  3. T = 120 × 1.5620 / 0.8 = 234.3 N
  4. Its x component, -180.0 N, is taken by the hinges along the axis

Answer: Cable tension T = 234 N

Chapter 8

Trusses: the method of joints

Which syllabus covers thisAU not in syllabusVTU BCIVC103 Module 3SPPU 101011 Unit IVMU not in syllabusKTU not in syllabus

What is a truss, and what is assumed when analysing one?

A truss is a frame of straight members joined at their ends into triangles, used for roofs, bridges, cranes and towers. Analysis assumes the joints are frictionless pins, loads and reactions act only at joints, and member weights are ignored or shared to the joints. Then every member is a two-force member: it is simply pulled (tension) or pushed (compression) along its own axis, with no bending. Real gusset-plate joints are stiffer than pins, but the pin model gives member forces within a few percent for slender members.

How do you know a plane truss can be solved by statics alone?

Each joint gives two equations, so j joints give 2j. The unknowns are m member forces plus 3 support reactions. A simple, statically determinate truss has m = 2j − 3: built up from one triangle by adding two members and one joint at a time. With fewer members it is a mechanism and collapses; with more it is redundant (statically indeterminate), and its member forces depend on member stiffness, which needs strength of materials. The count is necessary but not enough: members must also be arranged into rigid triangles.

How does the method of joints work?

Find the support reactions from the whole truss first. Then take a joint with at most two unknown members, draw its free-body diagram with every unknown member force assumed in tension (pulling away from the joint), and solve ΣF_x = 0 and ΣF_y = 0. A negative answer means compression. Move to the next joint that now has only two unknowns. Slide the load across the Pratt and Warren trusses below: chords near mid-span carry the most, and members swap between tension and compression as the load passes.

Method of joints: member forces of a Warren or Pratt truss under a moving load, tension or compression, and zero-force members: interactive loads as you scroll

How do you spot zero-force members?

Two rules, for joints with no external load. If only two non-collinear members meet at the joint, both carry zero force. If three members meet and two of them are collinear, the third carries zero force. In a Pratt truss with a single load, several verticals carry nothing. They are not useless: they brace long compression members against buckling and carry load when the load moves. Spot them first and the rest of the truss gets smaller.

Predict, then check

A 4-panel Pratt truss (24 m × 4 m) carries 100 kN at the middle bottom joint L2. The force in the middle vertical U2L2 is:

Worked examples

A triangular truss · Equilateral triangle ABC, 3 m sides, pin at A, roller at B, 10 kN down at the apex C
  1. By symmetry R_A = R_B = 5 kN
  2. Joint A: ΣF_y: F_AC sin 60° + 5 = 0
  3. F_AC = −5 / 0.8660 = -5.774 kN (compression)
  4. ΣF_x: F_AB + F_AC cos 60° = 0, F_AB = 2.887 kN (tension)
  5. Joint B mirrors A: F_BC = F_AC

Answer: AC = BC = 5.77 kN compression, AB = 2.89 kN tension

Pratt truss with a mid-span load · 4 panels of 6 m, height 4 m, 100 kN at L2; pin at L0, roller at L4
  1. Reactions 50 kN each; end diagonal L0U1 is 7.211 m long, sin θ = 4 / 7.211 = 0.5547
  2. Joint L0: F_L0U1 sin θ + 50 = 0, F_L0U1 = -90.14 kN; F_L0L1 = 90.14 × cos θ = 75 kN
  3. Joint L1 (no load, two collinear chords): U1L1 = 0 and L1L2 = 75 kN
  4. Joint U1: vertical: 90.14 sin θ = F_U1L2 sin θ, so F_U1L2 = 90.14 kN (tension); horizontal gives F_U1U2 = -150 kN
  5. Joint U2: U2L2 = 0

Answer: Top chord 150 kN C, bottom chords 75 kN T, diagonals 90.1 kN, verticals 0

Warren truss with an off-centre load · 4 panels of 6 m, height 4 m, apex joints T1-T4 above panel centres; 100 kN at L1 (6 m from the pin)
  1. Moments about L4: R_A × 24 = 100 × 18, R_A = 75 kN, R_B = 25 kN
  2. Diagonal L0T1 is 5 m long (3 across, 4 up): joint L0 ΣF_y: F × 0.8 + 75 = 0, F_L0T1 = -93.75 kN
  3. ΣF_x: F_L0L1 = 93.75 × 0.6 = 56.25 kN tension
  4. Joint T1: T1L1 = 93.75 kN tension and top chord T1T2 = 112.5 kN compression
  5. Past the load the shear is 75 − 100 = −25 kN, so the next diagonal L1T2 carries 31.25 kN tension

Answer: L0T1 93.75 kN C, L0L1 56.25 kN T, T1T2 112.5 kN C

Chapter 9

Method of sections, frames and cables

Which syllabus covers thisAU not in syllabusVTU BCIVC103 Module 3SPPU 101011 Unit IVMU not in syllabusKTU not in syllabus

What is the method of sections?

Cut the truss with an imaginary line through no more than three members whose forces you want, and treat one side as a free body. The cut members' forces act on it as external forces, and the three equilibrium equations give the three unknowns directly, without solving every joint from the support inwards. Assume every cut member is in tension, pulling away from the free body; a negative answer then means compression. It is the quick way to get one member deep inside a long bridge truss.

Method of sections: cut a Pratt truss through one panel and find three member forces from moment equations: interactive loads as you scroll

Where should you take moments in the method of sections?

About the point where two of the three cut members meet. Their forces pass through it and drop out, so one equation gives the third force. In a truss with parallel chords, moments about a top joint give the bottom chord force as the bending moment there divided by the depth, and moments about a bottom joint give the top chord. The diagonal then comes from vertical equilibrium: its vertical component carries the shear in that panel. That is why chords carry bending and diagonals carry shear.

How are frames and machines different from trusses?

A truss has only two-force members: pinned at both ends, loaded only at the pins, so each member's force acts along its own line. Frames and machines contain at least one multi-force member, such as a beam with a load in the middle or a lever with three pins. Their pin forces are not along the member, so you take the structure apart, draw each member separately with equal and opposite pin forces (Newton's third law), and solve the equations member by member. A frame is fixed and rigid; a machine, such as pliers, transmits and changes forces.

How do you analyse a cable carrying point loads?

A flexible cable can only pull along itself, so between loads it hangs in straight segments. The horizontal component of tension H is the same everywhere. Treat the span like a simply supported beam: the beam's bending moment at any load point equals H times the cable's sag there, so one known sag fixes H and then every other sag. Tension is largest in the steepest segment, next to the support with the bigger vertical reaction, and equals the square root of H² plus that reaction squared.

Predict, then check

A Pratt truss bridge carries the same load at every deck joint. Its diagonals (sloping down towards mid-span) are in:

Worked examples

Three members of a Pratt truss by one cut · Pratt truss, 6 panels of 3 m, 4 m deep, pin at L0 and roller at L6; 60 kN at L2. Find the forces in the members cut in panel 3 (U2U3, L2L3, U2L3)
  1. R_A = 60 × (18 − 6) / 18 = 40 kN
  2. Moments about U2 (x = 6 m): F_L2L3 × 4 = R_A × 6 = 240 → F_L2L3 = +60 kN
  3. Moments about L3 (x = 9 m): bending moment 40 × 9 − 60 × 3 = 180 kN·m → F_U2U3 = −180/4 = -45 kN
  4. ΣF_y on the left part: 40 − 60 − F_d × 4/5 = 0 → F_U2L3 = -25 kN
  5. Check ΣF_x: −45 + 60 + (−25)(3/5) = 0

Answer: Top chord 45 kN (C), bottom chord 60 kN (T), diagonal 25 kN (C)

Same truss under a deck load · 20 kN at each of L1 to L5; members cut in panel 2 (U1U2, L1L2, U1L2)
  1. By symmetry R_A = R_B = 100/2 = 50 kN
  2. Moments about U1 (x = 3 m): F_L1L2 = 50 × 3 / 4 = 37.5 kN
  3. Moments about L2 (x = 6 m): M = 50 × 6 − 20 × 3 = 240 kN·m → F_U1U2 = −240/4 = -60 kN
  4. Shear in panel 2 = 50 − 20 = 30 kN → F_U1L2 = 30 × 5/4 = 37.5 kN

Answer: Top chord 60 kN (C), bottom chord 37.5 kN (T), diagonal 37.5 kN (T)

Cable with two point loads · Supports level and 12 m apart; 10 kN hangs 4 m from A and 15 kN 8 m from A; sag under the 10 kN load is 2 m. Find H, the other sag and the largest tension
  1. As a beam: R_A = (10 × 8 + 15 × 4)/12 = 11.667 kN, R_B = 13.333 kN
  2. Moment at the 10 kN point = 46.667 kN·m = H × 2 → H = 23.333 kN
  3. Moment at the 15 kN point = 53.333 kN·m → sag = 53.333/23.333 = 2.286 m
  4. Steepest segment is at B: T_max = √(23.333² + 13.333²) = 26.87 kN (at A: 26.09 kN)

Answer: H = 23.33 kN, sag 2.29 m under the 15 kN load, T_max = 26.87 kN at B

Chapter 10

Laws of friction and the inclined plane

Which syllabus covers thisAU ME3351 Unit IVVTU BCIVC103 Module 3SPPU 101011 Unit IIMU FEC104 Module 3KTU GCEST103 Module 2

What are the laws of dry (Coulomb) friction?

Friction opposes the motion, or the motion about to happen, along the contact surface. Before slipping it is only as large as needed for equilibrium, up to a limit F = μs·N, where N is the normal reaction. The limit does not depend on the apparent contact area. Once sliding starts, friction drops to roughly μk·N, a little below the static value, and stays nearly constant with speed. These are empirical rules for dry, clean surfaces, not exact laws, but they hold well enough for most machine and structure problems.

What do the coefficient and the angle of friction mean?

μ is the ratio of limiting friction to normal reaction, measured for a pair of surfaces. Typical dry values: steel on steel about 0.5 to 0.8, wood on wood about 0.25 to 0.5, rubber on dry concrete about 0.6 to 0.85; a lubricated metal pair can drop to around 0.1. The angle of friction φ = tan⁻¹ μ is the angle the total reaction (N and F combined) makes with the normal at slipping. Spin that reaction round the normal and it sweeps the cone of friction: any reaction inside the cone is possible without slipping.

When does a block on an incline slide, and what force moves it?

With no push, the block stays put as long as the slope is no steeper than the angle of repose, tan α ≤ μ, so the angle of repose equals the angle of friction. To push it up you must beat both gravity's component and friction: along the slope P cos β must reach W sin α plus μ times the normal reaction, which a tilted push also reduces. To stop it sliding down on a steeper slope you need less, because friction now helps you.

Block on a rough incline pushed at an angle: holds, slips up or slides down; least force to push it up or hold it: interactive loads as you scroll

At what angle should you pull a load to need the least force?

At the angle of friction above the direction of motion. Tilting the pull upwards spends some force lifting the block, which lowers the normal reaction and so the friction. The best balance is β = φ, which makes the pull meet the total reaction at a right angle. On a slope α the least force becomes W sin(α + φ). For μ = 0.3 that is a tilt of 16.7°: pulling a sledge with a rope at that angle beats pushing horizontally.

Predict, then check

A crate rests on a 20° ramp; μ = 0.4 between crate and ramp. Left alone, it:

Worked examples

Push needed to move a block up and to hold it · W = 500 N on a 25° slope, μ = 0.3, push parallel to the slope
  1. N = W cos 25° = 453.2 N, so limiting friction μN = 135.9 N
  2. Weight down the slope: W sin 25° = 211.3 N
  3. Up: P = 211.3 + 135.9 = 347.3 N
  4. tan 25° = 0.466 > 0.3, so it slides on its own; to hold it: P = 211.3 − 135.9 = 75.4 N

Answer: 347 N to start it up the slope, 75 N to stop it sliding down

Best angle to push the same block · Same block; the push may be tilted β away from the slope
  1. φ = tan⁻¹ 0.3 = 16.70°
  2. P(β) = W(sin α + μ cos α)/(cos β + μ sin β) is least when β = φ
  3. P_min = W sin(α + φ) = 500 × sin 41.70° = 332.6 N
  4. Saving over the parallel push: 14.6 N (4.2%)

Answer: Tilt the push 16.7° off the slope: 332.6 N

Pulling a crate across a floor with a rope · W = 1,000 N on a level floor, μ = 0.25, rope at 30° above the horizontal
  1. N = 1,000 − P sin 30° (the rope lifts a little)
  2. At slipping: P cos 30° = 0.25 × (1,000 − P sin 30°)
  3. P = 250 / (0.866 + 0.125) = 252.3 N
  4. N = 873.9 N; check: P cos 30° = 218.5 N = 0.25 N

Answer: P = 252.3 N

Chapter 11

Ladder and wedge friction

Which syllabus covers thisAU ME3351 Unit IVVTU BCIVC103 Module 3SPPU 101011 Unit IIMU FEC104 Module 3KTU GCEST103 Module 2 (ladder)

How do you check whether a ladder will slip?

Draw the ladder's free-body diagram: its weight at the middle, the person's weight, a normal reaction and friction at the floor, and a normal reaction (plus friction, if the wall is rough) at the wall. At the point of slipping both frictions reach μN, with floor friction pointing towards the wall and wall friction pointing up. Horizontal and vertical balance give the reactions, and moments about the foot give how far up the person can stand. Climbing higher moves the weight's line of action out and raises the friction needed.

Ladder against a wall: how far a person can climb before it slips, with friction at the floor and the wall: interactive loads as you scroll

Why is a steeper ladder safer?

The weights try to rotate the ladder about its foot with a lever arm proportional to cos θ, while the wall's reaction resists with an arm proportional to sin θ. A steeper ladder shortens the first and lengthens the second, so the floor needs less friction. With a smooth wall, a 5 m ladder of 200 N and a 700 N person at the top need μ = 0.51 at 60°, but only 0.22 at 76°, the one-out-for-every-four-up rule that ladder safety guidance recommends.

How does a wedge lift a heavy load with a small push?

A wedge is an inclined plane you move under the load. A small angle α turns a long horizontal travel into a short lift, so the force needed is small, but friction acts on every sliding face: between load and wedge, between wedge and floor, and between the load and its guide. Each face's reaction tilts by the friction angle against the motion. Solve the load and the wedge as two free bodies, each with three forces or with its own equilibrium equations.

Wedge lifting a load: force to raise and to lower it, and when a wedge is self-locking: interactive loads as you scroll

When is a wedge self-locking?

When it stays in place after you stop pushing, so it must be pulled out. Removing the push reverses the motion, so every friction force reverses too. If the friction is large enough compared with the slope, the force needed to keep it in comes out negative: friction alone holds the load. For a wedge with friction on both faces the condition is α ≤ 2φ. Shims, door stops and the tapered keys on shafts rely on it; a screw jack is the same idea wrapped round a cylinder.

Predict, then check

A 10° wedge lifts a load, with μ = 0.2 on every face. When you stop pushing, the wedge:

Worked examples

How high can the person climb? · Ladder 5 m, 200 N, at 60° to the floor; smooth wall; floor μ = 0.3; person 700 N
  1. Smooth wall: N_floor = 200 + 700 = 900 N
  2. At slipping: F = 0.3 × 900 = 270 N = N_wall
  3. Moments about the foot: N_wall × 5 sin 60° = 200 × 2.5 cos 60° + 700 × s cos 60°
  4. 1169.1 = 250 + 350 s → s = 2.626 m

Answer: 2.63 m along the ladder (53% of the way up)

Floor friction needed to reach the top · Same ladder at 60°, person at the top (s = 5 m), smooth wall
  1. Moments about the foot: N_wall × 5 sin 60° = 200 × 2.5 cos 60° + 700 × 5 cos 60°
  2. N_wall = (250 + 1,750) / 4.330 = 461.9 N
  3. Floor friction = N_wall = 461.9 N; N_floor = 900 N
  4. μ needed = 461.9 / 900 = 0.513

Answer: μ ≥ 0.51

Force to raise and to lower a load with a wedge · W = 10 kN on a 10° wedge, block guided by a vertical wall, μ = 0.2 on all three faces, wedge weight ignored
  1. Block, raising: N1 = N2(sin α + μ cos α); ΣF_y: N2(cos α − μ sin α) − μN1 = W → N2 = W/((1 − μ²)cos α − 2μ sin α) = 11.416 kN
  2. N1 (wall) = 4.231 kN; floor N3 = N2(cos α − μ sin α) = 10.846 kN
  3. Wedge: P = N2(sin α + μ cos α) + μN3 = 6.400 kN
  4. Lowering (μ → −μ everywhere): P = -2.239 kN, negative, so it must be pulled out

Answer: Push 6.40 kN to raise; pull 2.24 kN to lower (self-locking, 10° < 2φ = 22.6°)

Chapter 12

Belt friction, wheel friction and rolling resistance

Which syllabus covers thisAU ME3351 Unit IVVTU not in syllabusSPPU 101011 Unit IIMU not in syllabusKTU not in syllabus

Why does a few turns of rope round a post hold a huge load?

Take a tiny piece of rope in contact with the drum. The tension on its two ends differs by the friction on it, and that friction is μ times the normal force, which itself grows with the tension. So the tension grows in proportion to itself as you go round: dT/dθ = μT, an exponential. On the point of slipping T1/T2 = e^(μθ) with θ in radians, independent of the drum's radius. With μ = 0.3, every full turn multiplies the holding power by about 6.6, which is how sailors hold a ship with one hand.

Rope and belt friction: tension ratio e^(μθ) around a drum, extra turns, and the power a flat belt carries: interactive loads as you scroll

How much power can a flat belt carry?

The belt drives the pulley through the difference between its tight side and slack side tensions, so power P = (T1 − T2)·v, and friction limits the ratio T1/T2 to e^(μθ), where θ is the wrap on the smaller pulley. At speed, part of the allowed tension is used up just holding the belt on the curve: the centrifugal tension m·v², with m the belt's mass per metre. Power therefore rises with speed, peaks when v = √(Tmax/3m), and then falls.

What is wheel or axle friction?

A wheel on a loose-fitting axle (a journal bearing) touches it along a line slightly up the side, where the bearing's reaction tilts by the friction angle. That reaction then misses the axle's centre by r sin φ, about μr for small μ, the radius of the friction circle. To keep the wheel turning steadily, the applied forces must provide a moment equal to the load times that offset. This is why axles are lubricated or carried on rolling bearings: it shrinks the offset.

What is rolling resistance?

A loaded wheel and the surface under it both deform a little, so the ground's reaction acts slightly ahead of the wheel's centre, by a distance a called the coefficient of rolling resistance (a length). The load times a makes a moment that must be overcome by a horizontal force P = W·a/r at the axle. For a steel wheel on a steel rail a is typically around half a millimetre; a car tyre on asphalt needs roughly 1 to 1.5% of the load. Both are far below sliding friction, which is why wheels win.

Predict, then check

A rope round a post with μ = 0.3: each extra full turn multiplies the load your hand can hold by about:

Worked examples

Holding a load with turns round a bollard · Rope with 2.5 turns round a bollard, μ = 0.3; load on the rope 5,000 N
  1. θ = 2.5 × 2π = 15.708 rad
  2. e^(μθ) = e^(4.712) = 111.3
  3. Hand force T2 = 5,000 / 111.3 = 44.9 N

Answer: about 45 N

Power a flat belt can transmit · Allowed tension 2,000 N, belt mass 0.4 kg/m, speed 20 m/s, μ = 0.3, wrap 180°
  1. Centrifugal tension m v² = 0.4 × 20² = 160 N
  2. T1 = 2,000 − 160 = 1840 N
  3. T1/T2 = e^(0.3π) = 2.566 → T2 = 717.0 N
  4. P = (T1 − T2) v = (1840 − 717.0) × 20 = 22.46 kW
  5. Best speed v = √(2,000 / (3 × 0.4)) = 40.8 m/s

Answer: 22.46 kW at 20 m/s (most power at 40.8 m/s)

Rolling resistance of a rail wagon wheel · Wheel radius 0.4 m carrying 5,000 N; coefficient of rolling resistance a = 0.5 mm (typical, steel on steel)
  1. Moment of the ground reaction about the axle: W × a
  2. Equal to the horizontal force at the axle times r: P × 0.4 = 5,000 × 0.0005
  3. P = 6.25 N
  4. Sliding the same wheel with μ = 0.5 would need 2,500 N, 400 times more

Answer: 6.25 N per wheel

Chapter 13

Centroids of lines and areas

Which syllabus covers thisAU ME3351 Unit IIIVTU BCIVC103 Module 4SPPU 101011 Unit IIMU FEC104 Module 1KTU GCEST103 Module 2

What is the difference between centroid, centre of mass and centre of gravity?

The centroid is a purely geometric point: the average position of a shape's area, volume or length. The centre of mass is the average position of its mass, and the centre of gravity is where its whole weight can be taken to act. For a uniform material in a uniform gravity field all three coincide, which is why engineering problems use them interchangeably. A plate made of two materials would have its centre of mass shifted towards the denser part, away from the centroid.

How is a centroid found by integration?

Slice the area into thin strips, take each strip's area times its distance from an axis (its first moment), add them up and divide by the total area. A triangle's centroid comes out at one third of its height from the base, a semicircle's at 4r/3π (0.424r) from the diameter, a quarter circle's at 4r/3π from each straight edge, and a circular sector of half-angle α at 2r sin α / 3α from the centre. Any axis of symmetry contains the centroid, which saves half the work.

How do you find the centroid of a built-up section like a T or an angle?

Split it into rectangles, circles and triangles whose centroids you already know. Tabulate each part's area and centroid coordinates, multiply, add the products and divide by the total area. A hole or cut-out is simply a part with negative area. Measure everything from one reference corner so no signs get mixed up. This is exactly the calculation behind every steel section table and the first step before computing a beam's moment of inertia.

Centroid of composite sections: T, I, L and channel shapes with a hole, located by ΣA·x / ΣA: interactive loads as you scroll

How do you find the centroid of a bent wire?

The same way, with lengths instead of areas: each straight piece's centroid is at its midpoint, and a circular arc of radius r and half-angle α has its centroid at r sin α / α from the centre. For a semicircular arc that is 2r/π (0.637r), further out than the semicircular plate's 0.424r because all of a wire's length lies on the rim. SPPU calls these wire bends; they matter for brackets, springs and frames made from rod.

Predict, then check

The centroid of a semicircular plate of radius r lies how far from its straight edge?

Worked examples

Centroid of a T-section · Flange 120 × 15 mm on a web 15 × 135 mm (overall depth 150 mm)
  1. Flange: A = 1,800 mm², ȳ = 150 − 7.5 = 142.5 mm
  2. Web: A = 2,025 mm², ȳ = 135/2 = 67.5 mm
  3. ΣA = 3,825 mm²; ΣAȳ = 256,500 + 136,687.5 = 393,187.5 mm³
  4. ȳ = 393,187.5 / 3,825 = 102.79 mm from the bottom; x̄ = 60 mm by symmetry

Answer: ȳ = 102.79 mm above the bottom of the web

Plate with a hole · Plate 200 × 150 mm with a hole of radius 40 mm centred 70 mm from the left edge and 90 mm from the bottom
  1. Plate: A = 30,000 mm² at (100, 75)
  2. Hole: A = −π × 40² = −5,026.5 mm² at (70, 90)
  3. Net area = 24,973.5 mm²
  4. x̄ = (30,000 × 100 − 5,026.5 × 70) / 24,973.5 = 106.04 mm
  5. ȳ = (30,000 × 75 − 5,026.5 × 90) / 24,973.5 = 71.98 mm

Answer: (106.04, 71.98) mm: the centroid moves away from the hole

Centroid of a D-shaped wire · A wire bent into a semicircular arc of radius 100 mm, closed by a straight wire along its diameter
  1. Arc: L = π × 100 = 314.16 mm, centroid 2r/π = 63.66 mm from the diameter
  2. Straight: L = 200 mm, centroid on the diameter (ȳ = 0)
  3. ȳ = (314.16 × 63.66) / (314.16 + 200) = 2r² / (πr + 2r) = 38.90 mm

Answer: 38.90 mm from the straight wire, on the axis of symmetry

Chapter 14

Pappus-Guldinus, distributed loads and centres of gravity of solids

Which syllabus covers thisAU ME3351 Unit IIIVTU not in syllabusSPPU not in syllabusMU FEC104 Module 1 (distributed forces)KTU not in syllabus

What do the theorems of Pappus-Guldinus say?

Spin a flat shape about an axis in its own plane that does not cut it. The volume swept out equals the shape's area times the distance its centroid travels, 2π x̄. The surface swept out equals the boundary's length times the distance the boundary's own centroid travels. So a ring, a pulley rim, a tank end or a sphere can be measured from a flat shape's centroid without any solid integration. A semicircle spun about its diameter gives 4πr³/3 and 4πr², the sphere's formulas.

Theorems of Pappus-Guldinus: surface area and volume of a solid of revolution from the generating shape's centroid: interactive loads as you scroll

How is a distributed load on a beam replaced by a single force?

The load intensity w(x) in N/m drawn along the beam makes a load diagram. Its resultant equals the area of that diagram and acts through the diagram's centroid. A uniform load w over length L becomes wL at the middle; a triangular load rising from zero to w becomes wL/2 at two thirds of the way towards the high end. Use the resultant for support reactions, but not for internal forces inside the loaded length: there you must cut the load too.

Where is the centre of gravity of common solids?

On every axis of symmetry, so for solids of revolution only the height along the axis is needed. A solid cone's centroid is h/4 above its base, a solid hemisphere's 3r/8 from its flat face, a hollow (thin-shell) hemisphere's r/2, and a cylinder's at mid-height. These come from integrating thin discs: each disc's volume times its height, divided by the total volume. A thin cone shell (no base) has its centroid at h/3 from the base.

How do you find the centre of gravity of a composite body?

Exactly as for areas, but with volumes (or masses, if the materials differ): ΣV·ȳ / ΣV. A toy made of a cone on a hemisphere stands upright only if the combined centre of gravity lies inside the hemisphere, below the joint, which needs h < √3·r. The same check tells you whether a machine, a crane or a loaded truck tips: its centre of gravity must stay above its base of support.

Predict, then check

You move a flat shape so its centroid is twice as far from the axis it is spun about. The solid's volume:

Worked examples

Volume and surface of a thick ring by Pappus · Rectangle 4 cm wide and 8 cm high, its inner edge 3 cm from the axis, spun once round the axis
  1. A = 4 × 8 = 32 cm², centroid x̄ = 3 + 2 = 5 cm
  2. V = 2π × 5 × 32 = 1005.3 cm³ (check: π(7² − 3²) × 8 = 1005.3 cm³)
  3. Boundary: inner side 8 cm at 3 cm, outer side 8 cm at 7 cm, two ends 4 cm at 5 cm
  4. S = 2π(8 × 3 + 8 × 7 + 2 × 4 × 5) = 2π × 120 = 754.0 cm²

Answer: V = 1005.3 cm³, S = 754.0 cm²

Reactions under a triangular load · Simply supported beam, 6 m span; load rises linearly from 0 at A to 12 kN/m at B
  1. Resultant = ½ × 6 × 12 = 36 kN
  2. It acts at the centroid of the triangle: 2/3 × 6 = 4 m from A
  3. ΣM_A: R_B × 6 = 36 × 4 → R_B = 24 kN
  4. R_A = 36 − 24 = 12 kN

Answer: R_A = 12 kN, R_B = 24 kN

Will the cone-and-hemisphere toy stand up? · Solid cone, radius 30 mm and height 120 mm, on a solid hemisphere of the same radius and material
  1. Cone: V = πr²h/3 = 113,097 mm³, centroid h/4 = 30 mm above the joint
  2. Hemisphere: V = 2πr³/3 = 56,549 mm³, centroid 3r/8 = 11.25 mm below the joint
  3. ȳ = (113,097 × 30 − 56,549 × 11.25) / 169,646 = 16.25 mm above the joint
  4. Above the joint, so it topples; it would self-right only if h < √3 r = 52.0 mm

Answer: Centre of gravity 16.25 mm above the joint: it falls over

Chapter 15

Area moments of inertia: parallel and perpendicular axes, polar, product and principal

Which syllabus covers thisAU ME3351 Unit IIIVTU BCIVC103 Module 4SPPU 101011 Unit IIMU not in syllabusKTU GCEST103 Module 2

What is the moment of inertia of an area, and why does it matter?

It is the second moment of area: each small piece of area times the square of its distance from an axis, summed over the shape. Area far from the axis counts heavily, so a deep section has a much larger value than a flat one of the same area. A beam's bending stiffness and strength depend on it directly, which is why beams are I-shaped. By integration, a rectangle gives bh³/12 about its centroid, a triangle bh³/36, and a circle πd⁴/64.

What is the parallel axis theorem?

The moment of inertia about any axis equals the value about the parallel axis through the centroid plus the area times the square of the distance between the two axes. For a built-up section, each part contributes its own centroidal I plus A·d², with d measured from the part's centroid to the whole section's centroid. In an I-beam the A·d² of the flanges supplies most of the stiffness, about 79% in a 200 mm deep section with 10 mm plates.

Area moment of inertia of I and T sections: parallel axis theorem, each part's share, radius of gyration and polar moment: interactive loads as you scroll

What are the polar moment of inertia and the radius of gyration?

The perpendicular axis theorem says that for a flat area the moment of inertia about an axis normal to it equals the sum about two perpendicular in-plane axes through the same point: J = Ix + Iy. This polar moment governs twisting of circular shafts (πd⁴/32 for a solid one). The radius of gyration k = √(I/A) is the distance at which the whole area, concentrated in a strip, would give the same I. Columns buckle about the axis with the smallest k.

What are the product of inertia and principal axes?

The product of inertia Ixy is the sum of x·y·dA about the centroidal axes. It is zero whenever either axis is an axis of symmetry, but not for an angle section. Rotating the axes changes Ix and Iy; the orientation where Ixy becomes zero gives the principal axes, with the largest and smallest moments of inertia. For an equal angle they lie at 45°, so it bends and buckles diagonally about the minor axis, a key check for angle struts in towers and trusses.

Predict, then check

You double the depth of a rectangular beam section, keeping its width. Its moment of inertia about the bending axis becomes:

Worked examples

I-section by the parallel axis theorem · Symmetric I-section: flanges 100 × 10 mm, web 10 × 180 mm, overall depth 200 mm
  1. Each flange: own I = 100 × 10³/12 = 8,333 mm⁴; A·d² = 1,000 × 95² = 9,025,000 mm⁴
  2. Web: 10 × 180³/12 = 4,860,000 mm⁴
  3. Ixx = 2 × (8,333 + 9,025,000) + 4,860,000 = 22,926,667 mm⁴ (check: (100 × 200³ − 90 × 180³)/12)
  4. Iyy = 2 × 10 × 100³/12 + 180 × 10³/12 = 1,681,667 mm⁴
  5. A = 3,800 mm², kx = √(Ixx/A) = 77.7 mm

Answer: Ixx = 22.93 × 10⁶ mm⁴, Iyy = 1.68 × 10⁶ mm⁴, kx = 77.7 mm

Moment of inertia of a T-section about its centroid · The T-section of chapter 13: flange 120 × 15, web 15 × 135, centroid 102.79 mm above the bottom
  1. Flange: 120 × 15³/12 + 1,800 × (142.5 − 102.79)² = 33,750 + 2,837,803
  2. Web: 15 × 135³/12 + 2,025 × (67.5 − 102.79)² = 3,075,469 + 2,522,491
  3. Ixx = 8,469,513 mm⁴

Answer: Ixx = 8.47 × 10⁶ mm⁴ about the centroidal axis

Principal axes of an equal angle · Angle 80 × 80 × 8 mm, split into a vertical leg 8 × 80 and a horizontal leg 72 × 8
  1. A = 640 + 576 = 1216 mm²; x̄ = ȳ = (640 × 4 + 576 × 44)/1,216 = 22.95 mm
  2. Ixx = Iyy = 737,298 mm⁴ (own I + A·d² of each leg)
  3. Ixy = Σ A·dx·dy = 640 × (4 − 22.95)(40 − 22.95) + 576 × (44 − 22.95)(4 − 22.95) = -436,547 mm⁴
  4. Ix = Iy, so 2θp = 90°: principal axes at 45°
  5. I_max = Ixx + |Ixy| = 1,173,845 mm⁴, I_min = Ixx − |Ixy| = 300,751 mm⁴

Answer: I_max = 1.174 × 10⁶ mm⁴ and I_min = 0.301 × 10⁶ mm⁴, about axes at 45°

Chapter 16

Mass moment of inertia

Which syllabus covers thisAU ME3351 Unit IIIVTU not in syllabusSPPU not in syllabusMU not in syllabusKTU GCEST103 Module 2

What is mass moment of inertia, and how is it different from the area moment of inertia?

Mass moment of inertia I = ∫r² dm measures how hard it is to change a body's rotation about an axis, in kg·m². It plays the part in rotation that mass plays in straight-line motion: torque = I × angular acceleration. The area moment of inertia ∫y² dA, in m⁴, has the same shape of integral but describes a cross-section's resistance to bending and has nothing to do with mass. For a thin flat plate of thickness t and density ρ the two are linked: I_mass = ρ·t·I_area about the same axis.

Which standard results are worth remembering?

About the axis through the centre unless stated: a slender rod mL²/12 (mL²/3 about one end); a thin ring or pipe mr²; a solid disc or cylinder about its own axis mr²/2; a solid sphere 2mr²/5; a thin hollow sphere 2mr²/3; a rectangular plate a × b about the axis normal to it m(a² + b²)/12; a solid cylinder about a diameter m(3r² + L²)/12. The further the mass sits from the axis, the bigger the number: a ring has twice the inertia of a disc of the same mass and radius.

How do the parallel axis theorem and radius of gyration work for mass?

If you know I_G about an axis through the centre of mass, the moment of inertia about any parallel axis a distance d away is I = I_G + m·d². A rod of 3 kg and 1.2 m has I_G = 0.36 kg·m²; about its end (d = 0.6 m) that becomes 0.36 + 3 × 0.36 = 1.44 kg·m². The radius of gyration k = √(I/m) is the distance at which the whole mass, packed into a ring, would give the same I. For a disc k = r/√2, about 0.71 r.

Why does a ring roll down a slope more slowly than a solid ball?

Rolling without slipping, part of the potential energy has to spin the body up as well as move it along. With I = m·k², the centre accelerates at a = g sinθ / (1 + k²/r²). A solid sphere (k²/r² = 0.4) gets 71% of g sinθ, a disc (0.5) 67%, a hollow sphere (0.67) 60% and a ring (1.0) only 50%. Mass and size cancel out: a heavy small ring and a light big ring arrive together. Friction must supply the spin torque; if μ is less than (k²/r²)·tanθ/(1 + k²/r²) the body slips.

Rolling race down an incline: ring, disc and spheres reach different speeds because of their mass moment of inertia: interactive loads as you scroll

How do you find a body's moment of inertia by integration?

Slice the body into pieces whose moment of inertia you already know, then add them up. A disc is a stack of thin rings, dI = r² dm with dm = σ·2πr dr, giving mr²/2. A solid sphere is a stack of thin discs, each contributing ½ (radius)² dm, giving 2mr²/5. For thin flat plates the perpendicular axis theorem saves work: the moment about the axis normal to the plate equals the sum of the moments about two perpendicular in-plane axes, I_z = I_x + I_y.

Predict, then check

A ring and a solid sphere of the same mass and radius are released together on a 3 m long, 20° slope. Which reaches the bottom first?

Worked examples

Moment of inertia of a steel flywheel disc · Solid steel disc, diameter 400 mm, thickness 50 mm, density 7,850 kg/m³
  1. Mass m = ρ·πr²·t = 7,850 × π × 0.2² × 0.05 = 49.32 kg
  2. I = ½ m r² = 0.5 × 49.32 × 0.2² = 0.9865 kg·m²
  3. Radius of gyration k = r/√2 = 141.4 mm
  4. Check: summing 4,000 thin rings, ∫ρt·2πr·r² dr, gives the same value

Answer: m = 49.3 kg, I = 0.986 kg·m², k = 141 mm

A pendulum made of a rod and a ball · Uniform rod 1.2 m, 3 kg, pivoted at one end; a 2 kg solid sphere of radius 0.1 m with its centre 1.3 m from the pivot
  1. Rod about its centre: mL²/12 = 3 × 1.44 / 12 = 0.36 kg·m²; about the end: + m(L/2)² = 1.44 kg·m²
  2. Sphere: 2mr²/5 + m d² = 0.4 × 2 × 0.01 + 2 × 1.3² = 3.388 kg·m²
  3. Total I = 1.44 + 3.388 = 4.828 kg·m²
  4. Radius of gyration k = √(I / 5 kg) = 0.983 m

Answer: I = 4.828 kg·m² about the pivot, k = 0.983 m

A solid cylinder rolling down a slope · Solid cylinder released from rest on a 30° slope 2 m long, rolling without slipping
  1. k²/r² = 0.5, so a = g sin 30° / 1.5 = 3.27 m/s²
  2. Speed at the bottom v = √(2aL) = √(2 × 3.27 × 2) = 3.617 m/s
  3. Time t = √(2L/a) = 1.106 s
  4. Energy check: g·h = ¾v² → 9.81 × 1.0 = 0.75 × 3.617² = 9.81
  5. Least friction coefficient to roll: 0.5 × tan 30° / 1.5 = 0.192

Answer: a = 3.27 m/s², v = 3.62 m/s after 1.11 s; needs μ ≥ 0.192

Chapter 17

Rectilinear motion and motion curves

Which syllabus covers thisAU ME3351 Unit VVTU BCIVC103 Module 5SPPU 101011 Unit VMU FEC104 Module 4KTU GCEST103 Module 3

What are displacement, velocity and acceleration for straight-line motion?

Pick an origin and a positive direction on the line. Position s says where the particle is; displacement is the change in s, which can be smaller than the distance travelled if the particle turns back. Velocity v = ds/dt is the rate of change of position and acceleration a = dv/dt the rate of change of velocity. When acceleration is given as a function of position, the chain rule gives a third form, a = v·dv/ds, which links speed to distance without time.

Which equations hold for constant acceleration?

Integrating a constant a twice gives three equations that cover every constant-acceleration problem: v = u + at, s = ut + ½at² and v² = u² + 2as, where u is the starting velocity. Choose the one that leaves out the quantity you do not know. Distances in successive equal time intervals from rest go 1 : 3 : 5 : 7, a quick check on any answer. They hold only while a is constant, so a trip with several phases is solved one phase at a time.

How is motion under gravity handled?

Near the Earth's surface and without air resistance, every falling body has the same constant acceleration g = 9.81 m/s² downward, so the constant-acceleration equations apply with a = −g if up is positive. A ball thrown up at 15 m/s stops after 15/9.81 = 1.53 s at a height of 15²/(2 × 9.81) = 11.5 m and returns to the hand at 15 m/s. Air drag matters for light or fast objects, which is why a feather and a hammer fall together only on the Moon.

What do the a-t, v-t and s-t graphs tell you?

The three motion curves are linked by slopes and areas. The slope of the s-t curve is the velocity and the slope of the v-t curve is the acceleration. The area under the a-t curve between two times is the change in velocity, and the area under the v-t curve is the displacement. A metro train that accelerates, cruises and brakes has a rectangular-step a-t graph, a trapezium v-t graph and an S-shaped s-t graph. Drawing them is often the fastest way to solve a multi-phase problem.

Motion curves: a three-phase acceleration profile drawn as a-t, v-t and s-t graphs, areas giving velocity and distance: interactive loads as you scroll

How do you solve problems with variable acceleration?

Integrate, choosing the form that matches how a is given. If a = f(t), integrate once for v(t) and again for s(t), using the starting values as constants. If a = f(v), separate variables as dt = dv/f(v). If a = f(s), use v dv = f(s) ds. For a = 6t − 4 m/s² with v = 2 m/s at t = 0, v = 3t² − 4t + 2 and s = t³ − 2t² + 2t. Check whether v changes sign: if it does, the distance travelled is not equal to the displacement.

Predict, then check

A car starts from rest with constant acceleration. Compared with the distance it covers in the first second, the distance in the second second is:

Worked examples

A metro train between two stations · From rest: accelerate at 1.0 m/s² for 15 s, cruise for 30 s, brake at 0.8 m/s² to rest
  1. Top speed v = a₁t₁ = 15 m/s (54 km/h)
  2. Accelerating: s₁ = ½ × 1.0 × 15² = 112.5 m; cruising: s₂ = 15 × 30 = 450 m
  3. Braking: t₃ = 15 / 0.8 = 18.75 s, s₃ = 15² / (2 × 0.8) = 140.625 m
  4. Total s = 703.125 m in 63.75 s; check: trapezium area ½(30 + 63.75) × 15 = 703.125 m

Answer: 703 m in 63.75 s, average speed 11.03 m/s

How deep is the well? · A stone is dropped into a well; the splash is heard 3.0 s later. Speed of sound 340 m/s
  1. Fall time t₁ and sound time h/340 add to 3.0 s, with h = ½ g t₁²
  2. ½ × 9.81 t₁² + 340 t₁ − 1,020 = 0
  3. t₁ = (−340 + √(340² + 2 × 9.81 × 340 × 3)) / 9.81 = 2.8803 s
  4. h = ½ × 9.81 × 2.8803² = 40.69 m (ignoring the sound would give 44.1 m)

Answer: h = 40.7 m

Variable acceleration a = 6t − 4 · a = 6t − 4 m/s², v = 2 m/s and s = 0 at t = 0; find v and s at t = 3 s
  1. v = ∫a dt = 3t² − 4t + 2 (constant from v(0) = 2)
  2. s = ∫v dt = t³ − 2t² + 2t (constant from s(0) = 0)
  3. At t = 3 s: v = 27 − 12 + 2 = 17 m/s, s = 27 − 18 + 6 = 15 m
  4. Least velocity where a = 0, t = 2/3 s: v = 0.667 m/s > 0, so the particle never reverses and distance = displacement

Answer: v = 17 m/s, s = 15 m at t = 3 s

Chapter 18

Curvilinear motion and projectiles

Which syllabus covers thisAU ME3351 Unit VVTU BCIVC103 Module 5SPPU 101011 Unit VMU FEC104 Module 4KTU GCEST103 Module 4

How do you describe motion along a curve with x-y components?

Write the position as two coordinates that change with time, x(t) and y(t). Velocity and acceleration then have components v_x = dx/dt, v_y = dy/dt, a_x = dv_x/dt and a_y = dv_y/dt, and each axis can be treated as its own straight-line problem. The velocity is always tangent to the path. Rectangular components are the natural choice when the forces have fixed directions, as gravity does for a projectile.

What are the equations of a projectile?

Without air resistance the only acceleration is g downward, so the horizontal velocity v cos α never changes and the vertical motion is free fall. Eliminating time gives a parabola. On level ground the time of flight is 2v sin α / g, the maximum height (v sin α)²/2g and the range v² sin 2α / g, which peaks at 45°. Angles α and 90° − α give the same range. Launched from a height, the time of flight comes from solving y(t) = 0, a quadratic.

Projectile motion: range, height and time of flight, and the tangential and normal acceleration and radius of curvature along the path: interactive loads as you scroll

What are the normal and tangential components of acceleration?

Path (n-t) coordinates follow the particle: t along the velocity, n toward the centre of curvature. The tangential acceleration a_t = dv/dt changes the speed; the normal acceleration a_n = v²/ρ changes the direction, where ρ is the radius of curvature at that point. A car at a steady 72 km/h on a 200 m radius curve still accelerates at 20²/200 = 2 m/s² toward the centre. For a projectile, gravity splits into these two parts; at the top a_t = 0 and a_n = g.

When are radial and transverse (polar) components used?

When a body moves around a fixed point, like a slider on a rotating arm or a radar tracking a plane, use r and θ. Velocity has a radial part ṙ and a transverse part r θ̇. Acceleration has a radial part r̈ − r θ̇², which includes the centripetal term, and a transverse part r θ̈ + 2 ṙ θ̇, which includes the Coriolis term 2ṙθ̇. A bead sliding outward at 1 m/s on a rod turning at 2 rad/s feels a Coriolis acceleration of 2 × 1 × 2 = 4 m/s².

How does relative motion work?

The velocity of A as seen from a moving B is v_A/B = v_A − v_B, a vector subtraction, and the same holds for accelerations when B does not rotate. Rain falling vertically at 8 m/s looks, to a cyclist riding at 6 m/s, as if it comes at 10 m/s from 37° ahead of vertical, so the cyclist tilts the umbrella forward. Relative motion turns a two-body chase or crossing problem into one body moving past a fixed one.

Predict, then check

Two balls are kicked at 20 m/s on level ground, one at 30° and one at 60°. Which goes further?

Worked examples

A football kicked at 40° · Launch speed 20 m/s at 40° above level ground, no air resistance
  1. Components: v cos 40° = 15.321 m/s, v sin 40° = 12.856 m/s
  2. Time of flight = 2 v sin α / g = 2.621 s
  3. Maximum height = (v sin α)² / 2g = 8.424 m
  4. Range = v² sin 80° / g = 400 × 0.98481 / 9.81 = 40.155 m

Answer: R = 40.2 m, H = 8.42 m, flight 2.62 s

A stone thrown from the top of a building · Thrown at 15 m/s, 30° above horizontal, from the roof of a 25 m building
  1. v_x = 12.990 m/s, v_y = 7.5 m/s up
  2. Landing: 25 + 7.5 t − 4.905 t² = 0
  3. t = (7.5 + √(7.5² + 2 × 9.81 × 25)) / 9.81 = 3.148 s
  4. Horizontal distance = 12.990 × 3.148 = 40.89 m
  5. Impact speed by energy: √(15² + 2 × 9.81 × 25) = 26.75 m/s, 60.9° below horizontal

Answer: Lands 40.9 m out after 3.15 s at 26.7 m/s

Car speeding up on a curve · Curve radius 200 m; at 72 km/h the driver accelerates at 1.5 m/s²
  1. v = 72 / 3.6 = 20 m/s
  2. Normal acceleration a_n = v²/ρ = 400 / 200 = 2.0 m/s²
  3. Tangential acceleration a_t = 1.5 m/s²
  4. Total a = √(2.0² + 1.5²) = 2.5 m/s², at 36.9° from the normal toward the direction of travel

Answer: a = 2.5 m/s², so the tyres must supply 2.5 N of grip per kg of car

Chapter 19

Newton's second law, D'Alembert's principle and connected bodies

Which syllabus covers thisAU ME3351 Unit VVTU BCIVC103 Module 5SPPU 101011 Unit VIMU FEC104 Module 6KTU GCEST103 Module 3

What does Newton's second law say, and how is it used?

The resultant force on a particle equals its mass times its acceleration, ΣF = m·a, with force in newtons, mass in kg and acceleration in m/s². It is a vector equation, so it gives one scalar equation per direction: along and across a slope, or x and y. The method: draw the free-body diagram with every force, choose axes, write ΣF = m·a for each axis, and solve. If the acceleration comes out negative, the body accelerates the other way.

What is D'Alembert's principle?

Move m·a to the other side: ΣF − m·a = 0. The term −m·a is treated as an extra, imaginary force, the inertia force, acting opposite to the acceleration. With it added, the body is in dynamic equilibrium and the familiar statics tools apply, including taking moments about any convenient point. It is the same physics as Newton's law, written so that a dynamics problem looks like a statics one. Passengers feel the inertia force as being pushed back into the seat when a bus pulls away.

Why does a person weigh more in a lift that is accelerating upward?

The scale reads the floor's push R on the person. For a 70 kg person, ΣF = R − mg = m·a. Accelerating up at 1.5 m/s², R = 70 × (9.81 + 1.5) = 792 N, so the scale reads about 81 kg. Accelerating down at 1.5 m/s², R = 582 N, about 59 kg. At constant speed in either direction R = mg. If the cable broke and the lift fell freely, a = g and R = 0: the person would feel weightless.

How do you solve connected bodies over a pulley?

Draw a separate free-body diagram for each body and write Newton's law for each. The rope links them: with a light, inextensible rope over a light, frictionless pulley, the tension is the same on both sides and the bodies have the same acceleration along the rope. With a movable pulley the hanging mass moves half as far, so its acceleration is half, and two rope segments hold it. First check whether motion happens at all: compare the driving force with the largest friction available.

Connected bodies over a pulley: a block on a rough incline and a hanging mass, acceleration and rope tension: interactive loads as you scroll

How is a body on a rough incline treated?

Take axes along and perpendicular to the slope. Across the slope there is no acceleration, so N = mg cosθ. Along it, gravity pulls with mg sinθ and kinetic friction μN opposes the motion. A block sliding down accelerates at g(sinθ − μ cosθ); one pushed up decelerates at g(sinθ + μ cosθ). If μ ≥ tanθ a block at rest stays at rest, so check the static case before assuming it moves.

Predict, then check

A 5 kg and a 3 kg mass hang over a light frictionless pulley (an Atwood machine). The rope tension is:

Worked examples

Weighing scale in a lift · 70 kg person standing on a scale in a lift; accelerations of 1.5 m/s² up and then down
  1. Free-body diagram: R up, mg down; ΣF = R − mg = m·a
  2. Up: R = 70 × (9.81 + 1.5) = 791.7 N, reads 80.7 kg
  3. Down: R = 70 × (9.81 − 1.5) = 581.7 N, reads 59.3 kg
  4. D'Alembert view: the inertia force −m·a adds to or subtracts from the weight

Answer: 792 N going up, 582 N going down

Block on a rough slope pulled by a hanging mass · m₁ = 5 kg on a 30° slope, μ = 0.2; rope over a fixed pulley to m₂ = 4 kg hanging
  1. m₁g sin 30° = 24.525 N, N = m₁g cos 30° = 42.479 N, friction μN = 8.496 N
  2. Pull of m₂ = 39.24 N > 24.525 + 8.496, so m₂ falls and the block slides up
  3. a = (39.24 − 24.525 − 8.496) / (5 + 4) = 0.6910 m/s²
  4. T = m₂(g − a) = 4 × (9.81 − 0.6910) = 36.476 N
  5. Check on the block: T − 24.525 − 8.496 = 3.4552 N = m₁a

Answer: a = 0.691 m/s², T = 36.48 N

The same system with a movable pulley · As above, but m₂ hangs from a movable pulley with the rope's end tied to the ceiling
  1. Two rope segments hold m₂, so the pull on the block is at most m₂g/2 = 19.62 N
  2. Gravity along the slope 24.525 N exceeds it by 4.905 N, but friction can supply up to 8.496 N up the slope
  3. So nothing moves: friction 4.905 N holds the block, tension = m₂g/2 = 19.62 N
  4. To drag the block up, m₂g/2 > 24.525 + 8.496 → m₂ > 6.73 kg

Answer: At rest (friction 4.90 N of 8.50 N); needs m₂ > 6.73 kg to move

Chapter 20

Work, energy, power and springs

Which syllabus covers thisAU ME3351 Unit VVTU not in syllabusSPPU 101011 Unit VIMU FEC104 Module 6KTU not in syllabus

What is the work done by a force?

Work is force times the distance moved in the force's direction: W = F·s·cosθ, in joules (N·m). A force across the motion, like the normal reaction on a sliding block, does no work. Gravity does work mg·h when a body descends a height h, whatever path it takes. Kinetic friction always does negative work, μN times the distance slid. A spring stretched from x₁ to x₂ does work ½k(x₁² − x₂²) on the body attached to it, negative while it is being compressed further.

What is the work-energy principle?

The total work done by all forces on a particle equals its change in kinetic energy: U₁₋₂ = ½mv₂² − ½mv₁². It links speed to distance directly, without finding the acceleration or the time, which makes it the quickest route when forces depend on position, as a spring's does. For connected bodies, apply it to the whole system: internal forces in an inextensible rope do no net work, so only external forces and friction appear.

What are conservative forces, and when is energy conserved?

A force is conservative if the work it does depends only on the start and end points, not the path: gravity and an ideal spring are. Their work can be stored as potential energy, mgh and ½kx². If only conservative forces do work, kinetic plus potential energy stays constant. Friction is not conservative: the work it does is turned into heat and cannot be recovered, so it appears in the energy equation as a loss.

How far does a block sliding into a spring compress it?

Follow the energy. A block released a distance d above a spring on a 30° slope loses potential energy mg(d + x) sinθ by the time it stops at compression x. That energy goes into the spring, ½kx², and into friction, μmg cosθ (d + x). Solving the quadratic gives x. Whether it then bounces back depends on whether the spring force kx beats gravity plus friction, mg(sinθ + μ cosθ). The interactive integrates the motion and shows the energy split as it happens.

Work and energy: a block slides down a rough incline into a spring, with kinetic, potential, spring energy and friction loss: interactive loads as you scroll

What are power and efficiency?

Power is the rate of doing work, P = dW/dt = F·v, in watts; 1 kW = 1,000 J/s. A lift motor raising 800 kg at a steady 1.5 m/s delivers 800 × 9.81 × 1.5 = 11.8 kW to the cage. Efficiency η is output power over input power; with η = 80% the motor draws 14.7 kW. Older units still appear in Indian catalogues: one metric horsepower is 735.5 W.

Predict, then check

A car brakes to a stop with the same tyre grip from 72 km/h instead of 36 km/h. The braking distance becomes:

Worked examples

Block on a rough slope into a spring · m = 2 kg released from rest 1.0 m above a spring (k = 1,000 N/m) on a 30° slope, μ = 0.2
  1. Net driving factor sinθ − μ cosθ = 0.5 − 0.2 × 0.8660 = 0.3268
  2. Speed reaching the spring: v = √(2 g d × 0.3268) = 2.532 m/s
  3. Energy at stop: ½ × 1,000 x² = 2 × 9.81 × 0.3268 × (1.0 + x) → 500x² − 6.4117x − 6.4117 = 0
  4. x = 119.8 mm
  5. Check: PE lost 10.986 J = spring 7.180 J + friction 3.806 J
  6. Spring force kx = 119.8 N > mg(sinθ + μ cosθ) = 13.21 N, so it rebounds 0.544 m up the slope

Answer: v = 2.53 m/s at the spring, compression 120 mm, rebound 544 mm

Braking distance and speed · Car braking on dry asphalt, μ = 0.7, wheels locked, from 72 km/h and from 36 km/h
  1. Work-energy: μmg·s = ½mv², the mass cancels: s = v²/(2μg)
  2. 72 km/h = 20 m/s: s = 400 / (2 × 0.7 × 9.81) = 29.12 m
  3. 36 km/h = 10 m/s: s = 7.28 m
  4. Reaction distance comes on top: at 20 m/s a 1 s reaction adds 20 m

Answer: 29.1 m from 72 km/h, 7.3 m from 36 km/h (4 : 1)

Power of a lift motor · Lift cage plus load 800 kg raised at a steady 1.5 m/s; motor and gearing efficiency 80%
  1. Steady speed: cable tension = weight = 800 × 9.81 = 7,848 N
  2. Output power P = F·v = 7,848 × 1.5 = 11,772 W
  3. Input power = 11,772 / 0.8 = 14,715 W
  4. Heat in the drive = 2,943 W

Answer: 11.77 kW to the cage, 14.71 kW drawn

Chapter 21

Impulse, momentum and impact

Which syllabus covers thisAU ME3351 Unit VVTU not in syllabusSPPU 101011 Unit VIMU FEC104 Module 6KTU not in syllabus

What is the impulse-momentum principle?

Integrate Newton's second law over time: the impulse of the force, ∫F dt, equals the change in momentum, m·v₂ − m·v₁. Momentum is a vector, in kg·m/s or N·s. The principle suits short, violent events where the force is unknown but the time is short: a 0.16 kg cricket ball arriving at 30 m/s and leaving at 40 m/s receives an impulse of 0.16 × 70 = 11.2 N·s. Over a 1.5 ms contact that is an average force of about 7,500 N. Longer contact, as with airbags or crumple zones, means a smaller force.

When is momentum conserved?

If no external impulse acts on a system, its total momentum stays the same. During a collision the contact forces between the bodies are internal: equal and opposite, so their impulses cancel. Gravity and other ordinary forces are tiny compared with the impact force over the few milliseconds of contact, so momentum is conserved through the impact even though kinetic energy usually is not. A gun recoils because the bullet's forward momentum must be balanced.

What is the coefficient of restitution?

Newton's experimental law: along the line of impact, the speed at which two bodies separate is e times the speed at which they approached, e = (v₂ − v₁)/(u₁ − u₂). e = 1 is perfectly elastic (kinetic energy kept), e = 0 perfectly plastic (the bodies stick together). A ball dropped from 2 m that bounces to 1.28 m has e = √(1.28/2) = 0.8.

How are velocities after a direct central impact found?

Two equations, two unknowns: conservation of momentum, m₁u₁ + m₂u₂ = m₁v₁ + m₂v₂, and the restitution law, v₂ − v₁ = e(u₁ − u₂). Solve them together. The kinetic energy lost is ½·m₁m₂/(m₁ + m₂)·(1 − e²)(u₁ − u₂)², which is zero only when e = 1. Equal masses in an elastic head-on impact swap velocities, which is why a moving snooker ball stops dead when it hits a stationary one full on.

Impact of two bodies: velocities after direct and oblique central impact for any coefficient of restitution, and the energy lost: interactive loads as you scroll

What changes in an oblique impact?

When the velocities are not along the line joining the centres, split each into components along the line of impact and across it. Along the line, apply momentum and restitution exactly as for a direct impact. Across the line, for smooth spheres there is no force, so each ball keeps its own transverse velocity. Recombine the components for the final speeds and directions. A ball striking a stationary ball of twice its mass at 30° leaves at about 109° to the line of impact, moving slightly backward along it.

Predict, then check

A moving ball hits an identical stationary ball head on, and the impact is perfectly elastic (e = 1). After impact:

Worked examples

Direct central impact of two balls · m₁ = 2 kg at 5 m/s to the right meets m₂ = 1 kg at 2 m/s to the left; e = 0.6
  1. Momentum: 2 × 5 + 1 × (−2) = 8 kg·m/s = 2v₁ + v₂
  2. Restitution: v₂ − v₁ = 0.6 × (5 − (−2)) = 4.2 m/s
  3. Solve: v₁ = (8 − 4.2)/3 = 1.2667 m/s, v₂ = (8 + 8.4)/3 = 5.4667 m/s (both to the right)
  4. KE before 27.0 J, after 16.547 J, lost 10.453 J
  5. Check by formula: ½ × (2 × 1/3) × (1 − 0.36) × 7² = 10.453 J

Answer: v₁ = 1.27 m/s, v₂ = 5.47 m/s, 10.45 J lost (39%)

Force on a cricket ball · 0.16 kg ball arrives at 30 m/s and is hit straight back at 40 m/s; contact time 1.5 ms
  1. Take the outgoing direction as positive: u = −30 m/s, v = +40 m/s
  2. Impulse = m(v − u) = 0.16 × 70 = 11.2 N·s
  3. Average force = impulse / time = 11.2 / 0.0015 = 7,467 N
  4. That is about 4,757 times the ball's weight

Answer: Impulse 11.2 N·s, average force about 7.47 kN

Oblique impact with a stationary ball · 1 kg ball at 6 m/s strikes a stationary 2 kg ball; its velocity makes 30° with the line of impact; smooth balls, e = 0.8
  1. Components of ball 1: along the line 5.1962 m/s, across 3.0 m/s
  2. Along the line: momentum 1 × 5.1962 = v₁ₓ + 2v₂ and v₂ − v₁ₓ = 0.8 × 5.1962
  3. v₁ₓ = 5.1962(1 − 1.6)/3 = -1.0392 m/s, v₂ = 5.1962 × 1.8 / 3 = 3.1177 m/s
  4. Across the line ball 1 keeps 3.0 m/s, so v₁ = √(-1.0392² + 3²) = 3.1749 m/s at 109.1° to the line of impact
  5. Energy lost = 3.240 J of 18 J

Answer: Ball 1: 3.17 m/s at 109°; ball 2: 3.12 m/s along the line

Chapter 22

Rigid bodies: rotation, plane motion and the instantaneous centre

Which syllabus covers thisAU not in syllabusVTU not in syllabusSPPU not in syllabusMU FEC104 Module 5KTU GCEST103 Module 4

What kinds of motion can a rigid body have in a plane?

Three. In translation every line in the body keeps its direction, so all points move alike: a lift cage, or a coupler rod of a locomotive (curvilinear translation). In rotation about a fixed axis every point moves on a circle about that axis: a flywheel or a door. General plane motion is everything else, and it can always be split into a translation of one point plus a rotation about it: a rolling wheel, a connecting rod, a ladder sliding down a wall.

What are the equations of rotation about a fixed axis?

Angular position θ (rad), angular velocity ω = dθ/dt and angular acceleration α = dω/dt mirror straight-line motion, so for constant α: ω = ω₀ + αt, θ = ω₀t + ½αt² and ω² = ω₀² + 2αθ. A point at radius r moves at v = rω and has a tangential acceleration rα and a normal (centripetal) acceleration rω² toward the axis. 600 rpm is 600 × 2π/60 = 62.8 rad/s.

What happens to a body rotating under a constant moment?

Newton's law for rotation about a fixed axis is ΣM = I·α. A constant net moment gives a constant angular acceleration, so the constant-α equations apply. A mass hanging from a rope wound on a drum is the classic case: the rope tension T turns the drum (T·r − friction torque = I·α) while the hanging mass obeys mg − T = m·a, and the rope ties them with a = α·r. The heavier the drum, the smaller the acceleration and the closer T comes to the full weight.

Rotation under a constant moment: a mass unwinding a rope from a drum, angular acceleration, rope tension and speed: interactive loads as you scroll

What is the instantaneous centre of rotation, and how is it found?

At any instant a body in plane motion is turning about one point, the instantaneous centre I, which itself has zero velocity at that instant. Every other point's velocity is ω times its distance from I and perpendicular to the line joining it to I. To find I, draw perpendiculars to the velocities of two points; they meet at I. For a ladder sliding down a wall, I is where the perpendicular to the wall through the top meets the vertical through the foot.

Instantaneous centre of rotation: a sliding ladder and a rolling wheel, and the velocity of any point from the ICR: interactive loads as you scroll

What does rolling without slipping mean?

The contact point does not slide, so it is at rest at that instant: it is the instantaneous centre. The centre moves at v = rω, the top of the wheel at 2v and any rim point at 2v·sin(φ/2), where φ is its angle from the contact point. A car at 72 km/h has the tops of its tyres moving at 144 km/h while the bottoms are momentarily still. Friction keeps the contact from sliding but does no work, because the contact point does not move.

How is the ICR of a two-link mechanism such as a slider-crank found?

The crank OA turns about the fixed pin O, so A's velocity is perpendicular to OA. The piston pin B slides along the stroke, so its velocity is along the stroke. The connecting rod AB's instantaneous centre is where the line OA (extended) meets the perpendicular to the stroke through B. Then ω_AB = v_A/IA and v_B = ω_AB·IB. When the crank is perpendicular to the stroke, the two lines are parallel: the ICR is at infinity and the rod momentarily translates.

Predict, then check

A wheel rolls without slipping with its centre moving at 10 m/s. The point at the top of the wheel moves at:

Worked examples

A mass unwinding from a drum · Solid-disc drum M = 10 kg, r = 0.2 m, bearing friction torque 0.5 N·m; hanging mass m = 2 kg released from rest
  1. I = ½Mr² = 0.2 kg·m²
  2. Drum: T·r − 0.5 = I·α; mass: mg − T = m·a; a = α·r
  3. α = (m g r − T_f)/(I + m r²) = (3.924 − 0.5)/(0.2 + 0.08) = 12.229 rad/s²
  4. a = α r = 2.4457 m/s², T = m(g − a) = 14.729 N
  5. After a 2 m drop: v = √(2a·2) = 3.128 m/s in 1.279 s
  6. Energy check: m g h = 39.24 J = ½mv² 9.783 + ½Iω² 24.457 + friction 5.0 J

Answer: α = 12.23 rad/s², a = 2.446 m/s², T = 14.73 N; 3.13 m/s after 2 m

Ladder sliding down a wall · 4 m ladder at 50° to the floor; its foot slides away from the wall at 1 m/s
  1. ICR: perpendicular to the floor through the foot B meets the perpendicular to the wall through the top A
  2. IB = L sin 50° = 3.0642 m, so ω = v_B / IB = 0.3264 rad/s
  3. IA = L cos 50° = 2.5712 m, so v_A = ω·IA = 0.8391 m/s down the wall (= v_B cot 50°)
  4. The midpoint is L/2 = 2 m from I (I, A, B and O form a rectangle), so v_mid = 0.6527 m/s

Answer: ω = 0.326 rad/s, top slides down at 0.839 m/s, midpoint 0.653 m/s

ICR of a slider-crank's connecting rod · Crank 100 mm at 45° from inner dead centre, connecting rod 350 mm, crank speed 600 rpm
  1. ω = 600 × 2π/60 = 62.832 rad/s; v_A = ω r = 6.2832 m/s
  2. Piston pin: x_B = r cos 45° + √(l² − r² sin² 45°) = 413.49 mm
  3. ICR: OA extended meets the vertical through B at (413.49, 413.49) mm; IA = 484.77 mm, IB = 413.49 mm
  4. ω_AB = v_A / IA = 12.961 rad/s; v_B = ω_AB·IB = 5.3594 m/s
  5. Check with the slider-crank formula rω(sin θ + sin 2θ / 2√(n² − sin²θ)), n = 3.5: 5.3594 m/s

Answer: ω_AB = 12.96 rad/s, piston speed 5.359 m/s

Keep going

Recommended reading

  • Vector Mechanics for Engineers: Statics and Dynamics, F. P. Beer, E. R. Johnston
  • Engineering Mechanics: Statics and Dynamics, R. C. Hibbeler
  • Engineering Mechanics: Statics and Dynamics, J. L. Meriam, L. G. Kraige
  • Engineering Mechanics, S. Timoshenko, D. H. Young
  • Engineering Mechanics, S. S. Bhavikatti
  • Engineering Statics: Open and Interactive, D. Baker, W. Haynes (free online)

How this book was made

Chapters follow the official syllabi listed above. Every interactive's formulas and every worked-example number were checked by script. Explanations, animations and examples are original to Skill-Lync. Topics informed by MIT OpenCourseWare 2.003SC (Engineering Dynamics), CC BY-NC-SA. All explanations, animations and examples are original to Skill-Lync; MIT does not endorse this page.

From the exam to a core job

Talk to a counsellor.

Ask how CAE engineers use engineering mechanics on real projects, and what the Post Graduate Program in Computer Aided Engineering (CAE) covers.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.