GATE Civil: Structural Analysis (trusses, deflections, indeterminate structures, influence lines), previous-year questions solved, part 2

Part 2 of 2 of the Structural Analysis hub: 13 more official GATE CE questions on indeterminate structures: consistent deformation, slope deflection, moment distribution, matrix methods and influence lines and moving loads, each solved step by step and checked against the official answer key. Part 1 covers determinacy, trusses, frames, arches and cables and deflections: energy, virtual work, moment-area, conjugate beam.

Questions from the ten official GATE CE papers, sessions CE1 and CE2 of GATE 2022 (IIT Kharagpur), 2023 (IIT Kanpur), 2024 (IISc Bengaluru), 2025 (IIT Roorkee) and 2026 (IIT Guwahati); solutions by Skill-Lync. · Updated 17 Nov 2026 · 13 of 28 questions on this page

GATE 2022 · CE1 · Q.51NAT · 2 marksIndeterminate structures: consistent deformation, slope deflection, moment distribution, matrix methods

Applied moment at joint F of a three-member fixed frame when the support moment at H is 10 kNm

Consider the linearly elastic plane frame shown in the figure. Members HF, FK and FG are welded together at joint F. Joints K, G and H are fixed supports. A counter-clockwise moment is applied at joint F. Consider flexural rigidity kN-m2 for each member and neglect axial deformations.

If the magnitude (absolute value) of the support moment at H is 10 kN-m, the magnitude (absolute value) of the applied moment (in kN-m) to maintain static equilibrium is ______. (round off to the nearest integer)

Plane frame: member HF vertical, 5 m long, from fixed support H above down to joint F; members FK and FG run down from F to fixed supports K and G, each 3 m to the side and 4 m below F. All members have EI = 10^5 kN m^2 and are welded at F, where a counter-clockwise moment M is appliedMFHKGEIEIEI5 m4 m3 m3 m

Answer: 60 kN-m Official key: 57 to 63

  1. With axial deformation neglected, the two inclined members stop F from moving, so the only unknown is the rotation of joint F. Every far end is fixed.
  2. Lengths: HF = 5 m, and FK = FG = m. With the same , each member has the same stiffness , so each distribution factor is .
  3. The applied moment splits equally: each member takes at F.
  4. The carry-over factor to a fixed far end is 1/2, so the moment at H is .
  5. , so 60 kN-m. cancels; its value is not needed.

Trap: forgetting the carry-over gives kN-m. Taking the inclined members as 4 m long (their height, not their length) gives kN-m. Both are outside the key.

Where this shows up in industry

Moment distribution, the Hardy Cross method, was the standard hand analysis for building frames before computers. Frame programs such as STAAD.Pro still use the same member stiffness, 4EI/L with a carry-over of one half to a fixed end, when they assemble the stiffness matrix.

GATE 2023 · CE2 · Q.26MSQ · 1 markIndeterminate structures: consistent deformation, slope deflection, moment distribution, matrix methods

Shear, displacement and slope at the midpoints of a closed square rigid frame squeezed by two equal forces

In the frame shown in the figure (not to scale), all four members (AB, BC, CD, and AD) have the same length and same constant flexural rigidity. All the joints A, B, C, and D are rigid joints. The midpoints of AB, BC, CD, and AD, are denoted by E, F, G, and H, respectively. The frame is in unstable equilibrium under the shown forces of magnitude acting at E and G. Which of the following statements is/are TRUE?

Closed square rigid frame ABCD (A top left, D top right, B bottom left, C bottom right) with midpoints E on AB, F on BC, G on CD and H on AD; two equal forces P push inward horizontally at E and at G along the horizontal centre linePPADBCHFEG
  1. (A)Shear forces at H and F are zero
  2. (B)Horizontal displacements at H and F are zero
  3. (C)Vertical displacements at H and F are zero
  4. (D)Slopes at E, F, G, and H are zero

Answer: (A), (B) and (D) Official key: A;B;D

  1. Frame and forces are symmetric about the vertical centre line HF and the horizontal centre line EG. The frame has no supports and is in self-equilibrium, so displacements are measured relative to its centre.
  2. On an axis of symmetry the antisymmetric quantities vanish: shear force, slope, and movement across the axis. H and F lie on HF, so the shear forces in AD and BC at H and F are zero (A) and H and F cannot move sideways (B).
  3. Each midpoint lies on a symmetry line (E, G on EG; H, F on HF), so the slopes at E, F, G and H are zero (D).
  4. Vertical movement along HF is symmetric, not antisymmetric, so it need not vanish: the forces push E and G inward, the rigid corners rotate, and AD and BC bow outward, H up and F down. (C) is false.
  5. A stiffness-matrix model of the frame (equal , axially rigid, side ) confirms it: zero shear and sideways movement at H and F, zero midpoint slopes, against inward. Answer: (A), (B) and (D).

Trap: adding (C). Symmetry about a line fixes only movement across it and the slope on it; the frame still changes shape along HF, so H and F move vertically.

Where this shows up in industry

Exploiting symmetry halves or quarters a model. Box culverts, closed ring frames and pipe sections are analysed this way: a quarter model with zero slope and zero shear at the cut lines gives the same moments as the whole frame.

GATE 2023 · CE2 · Q.54NAT · 2 marksIndeterminate structures: consistent deformation, slope deflection, moment distribution, matrix methods

Moment at the fixed base A of a symmetric portal frame whose cantilever overhangs carry a UDL w

For the frame shown in the figure (not to scale), all members (AB, BC, CD, GB, and CH) have the same length, and flexural rigidity, . The joints at B and C are rigid joints, and the supports A and D are fixed supports. Beams GB and CH carry uniformly distributed loads of per unit length. The magnitude of the moment reaction at A is . What is the value of (in integer)?

Portal frame: columns AB and DC of length L fixed at A and D, beam BC of length L, and cantilever overhangs GB and CH of length L, each overhang carrying a uniformly distributed load w; all members have the same EIwwGBCHADLLLL

Answer: Official key: 6 to 6

  1. The overhangs GB and CH are cantilevers: each applies a moment to its joint, anticlockwise at B and clockwise at C. BC carries no load, so no fixed-end moments.
  2. Frame and loads are symmetric, so there is no sway and . A member bent symmetrically like BC has rotational stiffness ; the column BA, fixed at A, has .
  3. Distribution factors at B: and .
  4. , and the carry-over to the fixed end A is half of it: .
  5. So . A stiffness-matrix run of the whole frame gives and no sway.

Trap: taking BC's stiffness as (factors 1/2 each) gives , ; forgetting the carry-over gives . Both are outside the key.

Where this shows up in industry

Cantilevered floor slabs, balconies and overhanging bridge decks load their supporting columns this way. The hogging moment at the overhang root flows into the columns, and symmetry tells the designer the frame will not sway under it.

GATE 2025 · CE1 · Q.29MSQ · 1 markIndeterminate structures: consistent deformation, slope deflection, moment distribution, matrix methods

Three-column portal frame with 100 kN.m couples at B and G: which statements about member CD and joint C hold?

Consider the frame shown in the figure under the loading of 100 kN.m couples at the joints B and G. Considering only the effects of flexural deformations, which of the following statements is/are true:

Portal frame with three fixed-base columns AB, DC and FG, each 6 m tall with flexural rigidity 2EI, joined by beams BC and CG, each 8 m long with rigidity 4EI. A clockwise 100 kN.m couple acts at joint B and an anticlockwise 100 kN.m couple at joint GBCGADF4EI4EI2EI2EI2EI100 kN.m100 kN.m8 m8 m6 m
  1. (A)Axial force is zero in the member CD
  2. (B)Shear force is zero in the member CD
  3. (C)There is no rotation in the joint C
  4. (D)The magnitude of bending moment developed in the member BC at the end C is more than 50 kN.m

Answer: (B) and (C) Official key: B;C

  1. The frame is symmetric about CD and the couples are mirror images (clockwise at B, anticlockwise at G), so the response is symmetric: joint C cannot rotate and the frame cannot sway. (C) is true.
  2. With C fixed in place and in rotation, and D fixed, column CD gets no end moments, hence no shear. (B) is true.
  3. Half frame, moment distribution at B: , , so . kN.m, carried over half: kN.m, under 50. (D) is false.
  4. Shear in BC kN, the same from CG, and both reach C: CD carries kN axially. (A) is false.
  5. Answer: (B) and (C).

Trap: zero moment and shear in CD do not mean zero axial force. The beams still pass their end shears into the column, and flexural-only analysis just means that axial force causes no shortening.

Where this shows up in industry

Designers use the same symmetry shortcut on real frames: under symmetric load the centre-line joint is treated as fixed against rotation and sway, which halves the model in hand checks of multi-bay portal frames and industrial sheds.

GATE 2025 · CE1 · Q.37MCQ · 2 marksIndeterminate structures: consistent deformation, slope deflection, moment distribution, matrix methods

Distribution factor of the stepped member AD (2EI then EI) at joint A of a rigid-jointed frame

In the rigid-jointed frame shown in the figure, the distribution factor of the member AD is closest to

Rigid-jointed frame meeting at joint A: member AB of length L and rigidity EI goes up to a hinge at B; cantilever AC of length L and rigidity 2EI is free at C; column AF of length L and rigidity 2EI is fixed at F; member AD of length L is fixed at D, with rigidity 2EI over the half next to A and EI over the half next to DBCADFEI2EI2EI2EIEILLL/2L/2L
  1. (A)0.254
  2. (B)0.267
  3. (C)0.398
  4. (D)0.421

Answer: (C) 0.398 Official key: C

  1. Stiffness of each member at A (moment per unit rotation): AB, far end hinged, ; AF, far end fixed, ; AC is a free cantilever and resists no rotation, so .
  2. AD is stepped, so does not apply. Fix D and find the flexibility at A (with from A): , , (units of ).
  3. Holding A against translation, .
  4. .
  5. Answer: (C) 0.398.

Trap: treating AD as uniform 2EI gives , option (D); as uniform EI, , option (B). Counting the cantilever AC as a member with stiffness is the other common slip.

Where this shows up in industry

Haunched beams and members with a thicker portion near the joint are common in portal frames and bridges; design software builds their stiffness the same way, by integrating the flexibility along the varying section instead of using 4EI/L.

GATE 2025 · CE2 · Q.38MCQ · 2 marksIndeterminate structures: consistent deformation, slope deflection, moment distribution, matrix methods

Reaction at the prop of a propped cantilever loaded by an end moment M when the prop settles by delta

The figure shows a propped cantilever with uniform flexural rigidity (in N.m2) and subjected to a moment (in N.m). Consider forces and displacements in the upward direction as positive.

Find the upward reaction at the propped support B (in N) when this support settles by , given in metres.

Propped cantilever AB of span L and flexural rigidity EI: fixed at A on the left, simply supported (propped) at B on the right, with a clockwise moment M applied at BMABLEIRedrawn, not to scale
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (C) Official key: C

  1. Remove the prop and treat (upward) as the redundant on a cantilever fixed at A (method of consistent deformation).
  2. Tip deflection from : .
  3. The clockwise moment at the free end puts the whole cantilever in uniform hogging, so the tip moves down by .
  4. Compatibility: the tip must end at the settled prop, : .
  5. So , answer (C). Check: with no settlement , the standard result.

Trap: in (A) is the end shear from a settlement of a beam fixed at both ends; with a prop (free to rotate at B) the stiffness against settlement is only .

Where this shows up in industry

Support settlement is a load case in its own right: IS 456 and bridge codes ask designers to check continuous beams and propped members for differential settlement, because an indeterminate member picks up forces from movement alone, as the 3EI delta over L cubed term shows.

GATE 2025 · CE2 · Q.52NAT · 2 marksIndeterminate structures: consistent deformation, slope deflection, moment distribution, matrix methods

Force in the centre rod when a flexible steel beam hung from three steel rods carries a UDL

A steel beam supported by three parallel pin-jointed steel rods is shown in the figure. The moment of inertia of the beam is mm4. Take modulus of elasticity of steel as 210 GPa. The beam is subjected to uniformly distributed load of 6.25 kN/m, including its self-weight.

The axial force (in kN) in the centre rod CD is ______ (round off to one decimal place).

Steel beam B-D-F, 4 m long, hung from a rigid ceiling by three parallel pin-jointed vertical steel rods 1 m long: AB of 12 mm diameter at the left end, CD of 30 mm diameter at mid-span, EF of 12 mm diameter at the right end; a uniformly distributed load of 6.25 kN/m acts on the whole beam6.25 kN/mACEBDF12 mm dia30 mm dia12 mm dia2 m2 m1 mRedrawn, not to scale

Answer: 16.5 Official key: 16.3 to 16.6

  1. Total load kN. Let CD carry ; by symmetry AB and EF carry each. One equation is missing, so use compatibility at D.
  2. Rod areas: 12 mm, mm2; 30 mm, mm2. Stretch of a rod: with mm, MPa.
  3. Bending of the beam between the end rods moves D down relative to the line B-F by with mm, N mm2: mm.
  4. Compatibility: stretch of AB + beam term = stretch of CD, i.e. .
  5. So N, that is 16.5 kN (end rods 4.26 kN each). Check: AB stretches mm and CD mm; the beam term is mm, so the stiff centre rod holds mid-span slightly above the line of the end rods.

Trap: a rigid beam gives kN; rigid supports under a continuous beam give kN; an equal share gives kN. All three are outside the key: the beam's bending and the rods' stretch both matter.

Where this shows up in industry

Hung floors and pipe racks on hangers behave like this: the stiffer hanger attracts load in proportion to its stiffness relative to the beam, so a hanger that is shortened, stiffened or slack during erection can change its force well beyond the design share.

GATE 2026 · CE1 · Q.38MCQ · 2 marksIndeterminate structures: consistent deformation, slope deflection, moment distribution, matrix methods

Stiffness matrix of a two-member truss inclined at 45 degrees, hinged at P and R, after boundary conditions

A plane truss consists of two linearly elastic, homogeneous, identical members, namely PQ and QR. Both members have length (), cross-sectional area (), and modulus of elasticity (). The members are inclined at as shown in the figure. The truss has hinge supports at P and R. The translational degrees-of-freedom ( and ) are shown at joint Q.

After application of the boundary conditions, the stiffness matrix of the truss becomes:

Plane truss: members PQ and QR, each with area A, modulus E and length L, rise at 45 degrees from hinge supports P and R to the apex joint Q; the degrees of freedom at Q are u horizontal and v verticaluvQPRA, E, LA, E, L45°45°Redrawn, not to scale
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (C) Official key: C

  1. In global axes, a pin-jointed member adds to the stiffness of its free joint, where and are its direction cosines.
  2. PQ rises from P to the right at : , so it adds .
  3. QR rises from R to the left: , , so it adds the same matrix with off the diagonal.
  4. P and R are hinged, so only and at Q remain. Adding the two: .
  5. Answer (C).

Trap: keeping one member and doubling it gives (A) or (D). The off-diagonal terms cancel because the truss is symmetric: a horizontal push at Q produces no vertical force. Each diagonal term is .

Where this shows up in industry

STAAD.Pro, ETABS and every other frame program work this way: each member's local stiffness is rotated into global axes with its direction cosines and added into the structure matrix, the supported degrees of freedom are struck out, and the rest is solved for joint displacements.

GATE 2022 · CE1 · Q.52NAT · 2 marksInfluence lines and moving loads

Maximum bending moment at R under a two-axle truck (100 kN and 200 kN, 3 m apart) crossing a 5 m beam

Consider a simply supported beam PQ as shown in the figure. A truck having 100 kN on the front axle and 200 kN on the rear axle, moves from left to right. The spacing between the axles is 3 m. The maximum bending moment at point R is ______ kNm. (in integer)

Simply supported beam PQ, 5 m long, pinned at P and on a roller at Q; point R is 1 m from P and 4 m from QPRQ1 m4 m

Answer: 180 kNm Official key: 180 to 180

  1. Influence line for the moment at R ( m, m, m): a triangle with peak m at R, falling to zero at P and Q. To the right of R the ordinate is .
  2. Moving left to right, the 100 kN front axle leads and the 200 kN rear axle follows 3 m behind.
  3. Rear axle at R: the front axle is at m, ordinate . kNm.
  4. Front axle at R puts the rear axle off the beam: kNm. Between these positions rises as the rear axle approaches R and falls after it passes.
  5. Maximum: 180 kNm.

Trap: counting only the heavy axle at R gives 160 kNm. The front axle still sits on the beam, 1 m from Q, and adds 20 kNm.

Where this shows up in industry

Bridge girders are designed for the worst position of the IRC vehicle loads. Influence lines tell the designer where to place each axle, and bridge software runs the same moving-load sweep at every section of every span.

GATE 2023 · CE2 · Q.17MCQ · 1 markInfluence lines and moving loads

What the Muller-Breslau principle is used for in the analysis of structures

Muller-Breslau principle is used in analysis of structures for _______________.

  1. (A)drawing an influence line diagram for any force response in the structure
  2. (B)writing the virtual work expression to get the equilibrium equation
  3. (C)superposing the load effects to get the total force response in the structure
  4. (D)relating the deflection between two points in a member with the curvature diagram in-between

Answer: (A) drawing an influence line diagram for any force response in the structure Official key: A

  1. The Müller-Breslau principle: the influence line of any force response (reaction, shear or bending moment) has the shape of the deflected structure obtained by removing the restraint that carries that response and imposing a unit displacement in its direction.
  2. For a reaction, remove the support and lift it by one unit; for shear at a section, cut it and impose a unit relative sliding; for bending moment, insert a hinge and impose a unit relative rotation.
  3. It works for determinate structures (straight-line influence lines) and indeterminate ones (curved lines). It is used for (A) drawing an influence line diagram for any force response.

Trap: (B) describes the principle of virtual work, from which Müller-Breslau is derived; (C) is the principle of superposition; (D) is the moment-area theorem. Each is a real tool, but only (A) is what this principle does.

Where this shows up in industry

Bridge engineers use influence lines to place IRC vehicle loads for the worst reaction, shear or moment. A Muller-Breslau sketch shows the shape and the critical load positions quickly; software such as STAAD.Pro or Midas Civil then computes the ordinates.

GATE 2024 · CE2 · Q.50NAT · 2 marksInfluence lines and moving loads

Maximum fixing moment at P of a beam fixed at P, hinged at Q and pinned at R under a moving 10 kN load

The horizontal beam PQRS shown in the figure has a fixed support at point P, an internal hinge at point Q, and a pin support at point R. A concentrated vertically downward load (V) of 10 kN can act at any point over the entire length of the beam.

The maximum magnitude of the moment reaction (in kN.m) that can act at the support P due to V is ____________ (in integer).

Beam PQRS: fixed at P, hinge at Q, pin at R, overhang to SPQRS15 m10 m5 m

Answer: 150 kN m Official key: 150 to 150

  1. The influence line of for a beam with a hinge is made of straight lines: draw it by placing a unit load on each part.
  2. Load on PQ at distance from P: PQ acts as a cantilever, , up to at Q.
  3. Load on QRS at distance beyond Q: QRS is a beam on the hinge Q and the pin R, so the hinge passes down . Then , falling from 150 at Q to 0 at R.
  4. At S (), (an uplift), giving of the opposite sign, smaller in size.
  5. Maximum magnitude: 150 kN m, with the load at the hinge Q.

Trap: taking only the overhang (75 kN m) or treating P to R as one 25 m cantilever (250 kN m). The hinge cuts the moment path, so no load beyond Q can do more than a load at Q.

Where this shows up in industry

Cantilever-and-suspended-span bridges (Gerber beams) use exactly this layout; designers draw the influence line of each support moment to place lane loads where they hurt most.

GATE 2025 · CE2 · Q.14MCQ · 1 markInfluence lines and moving loads

Influence line for the force in bottom-chord member G-I of a six-panel truss with mid-height joints

Consider the pin-jointed truss shown in the figure. Influence line is drawn for the axial force in the member G-I, when a unit load travels on the bottom chord of the truss. Identify the CORRECT influence line from the following options:

Note: Positive value corresponds to tension and negative value corresponds to compression in the member.

Pin-jointed truss of six 6 m panels, 36 m span, pin support at A and roller at P. Bottom chord joints A, D, G, I, L, O, P; top chord B, E, H, J, M at 6 m height; mid-height joints C, F, K, N at 3 m on the verticals B-D, E-G, J-L and M-O. Diagonals C-E, C-G, F-H, F-I, K-H, K-I, N-J, N-L, vertical H-I, end posts A-B and M-PADGILOPBEHJMCFKN6 @ 6 m = 36 m3 m3 mRedrawn, not to scale
  1. (A)Option A: influence line, positive triangle, zero at A and P, peak 1.33 under D1.33+DAP
  2. (B)Option B: influence line, positive triangle, zero at A and P, peak 1.33 under G1.33+GAP
  3. (C)Option C: influence line, positive triangle, zero at A and P, peak 1.33 under I1.33+IAP
  4. (D)Option D: influence line, +1.33 under G changing sign to -1.33 under I, zero at A and P1.331.33+−GIAP

Answer: (B) Positive triangle, zero at A and P, peak 1.33 under G Official key: B

  1. Cut the truss through panel G-I. The section cuts four members: E-H, F-H, F-I and G-I.
  2. Joint F has only two inclined members, F-H and F-I, of equal slope. Horizontal equilibrium at F makes their forces equal and opposite, so together they push or pull straight up or down along the vertical through F, which is the line E-F-G.
  3. Take moments about E (12 m from A, 6 m above the bottom chord): E-H passes through E and the F-H/F-I pair acts on the vertical through E, so only G-I is left: , the bending moment at m of a 36 m simply supported beam.
  4. The influence line of is a triangle with peak under G. Divided by 6: peak under G, positive (tension, as for any bottom chord of a simply supported truss); under I it is .
  5. Answer (B).

Trap: (A) and (C) have the right shape with the peak under the wrong joint; the peak of a chord's influence line sits under its moment centre, here E above G. Taking moments about H instead fails because F-H also passes through H. A change of sign as in (D) is the mark of a web member, never a chord.

Where this shows up in industry

Bridge engineers draw exactly these lines to place the IRC Class AA or 70R vehicle for the worst force in each chord. Load rating of old steel truss bridges in India still relies on them before a heavy consignment is allowed across.

GATE 2026 · CE2 · Q.38MCQ · 2 marksInfluence lines and moving loads

Influence line of the end rotation at support B of a simply supported beam of span L

A simply supported, linearly elastic, homogeneous, prismatic beam of length L and flexural rigidity EI is shown in the figure.

The expression for the Influence Line Diagram (ILD) of the rotation at the support B is

Simply supported beam AB of span L, pin at A and roller at B, a downward load at distance x from A; dashed deflected shape; theta B of x is the rotation of the beam end at support BxθB(x)ABLRedrawn, not to scale
  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (B) Official key: B

  1. The ILD of is the rotation at B caused by a unit load at distance from A.
  2. For a load at from A (), the end rotation is . With , :
  3. Maxwell's reciprocal theorem gives the same: it equals the deflection at due to a unit couple at B.
  4. Option (B) is this expression with the sign that makes negative under a downward load (clockwise positive). It is zero at both supports and gives at mid-span (check: for ); the peak is at .
  5. Answer (B).

Trap: (D) has the right shape but is twice as large. (A) is not zero for a load at A, where no bending occurs. (C) is symmetric and gives at mid-span instead of .

Where this shows up in industry

Bridge bearing designers use influence lines for girder end rotation to place vehicle axles where they turn the girder end the most, because elastomeric bearings and expansion joints are specified for a maximum end rotation as well as a maximum vertical load.

From GATE prep to a structural analysis and design career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.