GATE Civil: Geomatics Engineering (surveying, levelling, bearings and traversing, photogrammetry), previous-year questions solved, part 2

Part 2 of 2 of the Geomatics Engineering hub: 21 more official GATE CE questions on distance, angles, traversing and triangulation and photogrammetry, remote sensing and GIS, each solved step by step and checked against the official answer key. Part 1 covers surveying principles, errors and maps and levelling and trigonometric levelling.

Questions from the ten official GATE CE papers, sessions CE1 and CE2 of GATE 2022 (IIT Kharagpur), 2023 (IIT Kanpur), 2024 (IISc Bengaluru), 2025 (IIT Roorkee) and 2026 (IIT Guwahati); solutions by Skill-Lync. · Updated 17 Nov 2026 · 21 of 36 questions on this page

GATE 2022 · CE1 · Q.24MCQ · 1 markDistance, angles, traversing and triangulation

Corrected horizontal length of a 350 m line taped on a 1 in 5 slope with a 50 m tape that is 0.1 m short

A line between stations P and Q laid on a slope of 1 in 5 was measured as 350 m using a 50 m tape. The tape is known to be short by 0.1 m.

The corrected horizontal length (in m) of the line PQ will be

  1. (A)342.52
  2. (B)349.30
  3. (C)356.20
  4. (D)350.70

Answer: (A) 342.52 Official key: A

  1. A short tape is laid down more times than it should be, so it over-reads. True length = measured length (actual tape length / nominal length).
  2. m along the slope.
  3. A slope of 1 in 5 rises 1 m per 5 m horizontally, so and .
  4. Horizontal length 342.52 m, option (A).

Trap: stopping after the tape correction gives (B) 349.30; dividing by gives 356.22 m, (C); adding the 0.1 m per tape length instead of removing it gives (D) 350.70. Reading 1 in 5 as gives 342.24 m, which is not offered.

Where this shows up in industry

Tape corrections for standardisation, slope, temperature, pull and sag are still applied when a baseline is measured or a tape is checked against a calibrated range; a total station does the slope reduction itself from the vertical angle it measures with every distance.

GATE 2022 · CE1 · Q.35NAT · 1 markDistance, angles, traversing and triangulation

Azimuth from north of a survey line with quadrantal bearing N31 degrees 17 minutes W

The bearing of a survey line is N31°17′W. Its azimuth observed from north is ______ deg. (round off to two decimal places)

Answer: 328.72 deg Official key: 328.60 to 328.80

  1. A quadrantal (reduced) bearing is measured from north or south towards east or west. NθW lies in the north-west quadrant, between 270° and 360°.
  2. Azimuth (whole circle bearing) is measured clockwise from north, so for NθW: .
  3. Convert the minutes: .
  4. 328.72°.

Trap: treating 31°17′ as 31.17° gives 328.83°, just outside the key. Mixing up the quadrant gives 31.28° (NE), 148.72° (SE) or 211.28° (SW).

Where this shows up in industry

Total stations, GNSS controllers and GIS software store directions as azimuths clockwise from north, while older deeds and cadastral sketches often give quadrantal bearings, so this conversion comes up whenever an old boundary is re-established.

GATE 2022 · CE2 · Q.24MCQ · 1 markDistance, angles, traversing and triangulation

Magnetic declination at a place where the magnetic bearing of the Sun at noon is S 2 degrees E

If the magnetic bearing of the Sun at a place at noon is S 2° E, the magnetic declination (in degrees) at that place is

  1. (A)2° E
  2. (B)2° W
  3. (C)4° E
  4. (D)4° W

Answer: (A) 2° E Official key: A

  1. At local noon the Sun crosses the true meridian, so its true bearing is due south: .
  2. The magnetic bearing S 2° E is 2° short of due south, measured clockwise from magnetic north: .
  3. Declination = true bearing magnetic bearing . Positive means magnetic north lies east of true north.
  4. Answer: (A) 2° E.

Trap: subtracting the other way gives 2° W, option (B). Check it physically: if the needle points 2° east of true north, every magnetic bearing reads 2° less than the true one, which is what S 2° E (178°) against 180° shows.

Where this shows up in industry

Magnetic declination differs from place to place and drifts every year, so bearings from an old compass survey must be corrected to true bearings before a boundary is re-set; surveyors take the value for the date and place from a geomagnetic model.

GATE 2023 · CE1 · Q.22MCQ · 1 markDistance, angles, traversing and triangulation

Vertical collimation correction of a theodolite from direct and reversed zenith angles of 56 and 303 degrees

The direct and reversed zenith angles observed by a theodolite are and , respectively. What is the vertical collimation correction?

  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (D) Official key: D

  1. A zenith angle is measured from the vertical. Sighting the same point on face left (direct) and face right (reversed), a perfect instrument gives readings that add up to exactly .
  2. Here the sum is , short of by .
  3. That shortfall is shared equally by the two faces, so the vertical index (collimation) error of each reading is .
  4. The correction is the negative of the error: , option (D).
  5. Check: corrected readings and add to , and the true zenith angle is (vertical angle above the horizon).

Trap: option (C) is the error itself, and (A) or (B) is the whole misclosure. A correction always has the opposite sign of the error and is applied to each single-face reading.

Where this shows up in industry

On site the same check is a two-face observation: total stations have a vertical index (V0) calibration that measures this half-difference on both faces, stores it, and applies it to every single-face zenith angle afterwards.

GATE 2023 · CE2 · Q.24MCQ · 1 markDistance, angles, traversing and triangulation

Magnetic declination of a place when the magnetic bearing of the sun at noon is 183 degrees 30 minutes

The magnetic bearing of the sun for a location at noon is . If the sun is exactly on the geographic meridian at noon, the magnetic declination of the location is ______.

  1. (A) W
  2. (B) E
  3. (C) W
  4. (D) E

Answer: (A) W Official key: A

  1. At local noon the sun is on the geographic (true) meridian. A magnetic bearing near shows it is the southern end of that meridian: true bearing .
  2. Whole circle bearings are related by true bearing = magnetic bearing + declination, with declination positive when magnetic north lies east of true north.
  3. , so .
  4. A negative declination means magnetic north is west of true north: (A) W.
  5. Check: with magnetic north turned west, every magnetic bearing reads more than the true one, and .

Trap: reversing the sign rule and answering E. Remember: magnetic bearing larger than true bearing means declination west. The options come from measuring against east instead of the meridian.

Where this shows up in industry

Declination varies with place and drifts over the years, so survey plans state whether bearings are true, grid or magnetic, and the date of a magnetic one. Field crews set it in compasses and GNSS controllers rather than correcting by hand.

GATE 2023 · CE2 · Q.46MCQ · 2 marksDistance, angles, traversing and triangulation

Latitude and departure of P after four 5 km legs on whole circle bearings 120, 0, 90 and 240 degrees

A delivery agent is at a location R. To deliver the order, she is instructed to travel to location P along straight-line paths of RC, CA, AB and BP of 5 km each. The direction of each path is given in the table below as whole circle bearings. Assume that the latitude (L) and departure (D) of R is (0, 0) km. What is the latitude and departure of P (in km, rounded off to one decimal place)?

PathsRCCAABBP
Directions (in degrees)120090240
Plan of the delivery path: from R on bearing 120 degrees to C, 0 degrees to A, 90 degrees to B and 240 degrees to P, each leg 5 km; P ends 5 km due east of RN120°0°90°240°RCABPEach leg 5 km
  1. (A)L = 2.5; D = 5.0
  2. (B)L = 0.0; D = 5.0
  3. (C)L = 5.0; D = 2.5
  4. (D)L = 0.0; D = 0.0

Answer: (B) L = 0.0; D = 5.0 Official key: B

  1. For a line of length on whole circle bearing : latitude (northing) , departure (easting) .
  2. RC, : , .
  3. CA, : , .
  4. AB, : , .
  5. BP, : , .
  6. Sum: km and km: (B) L = 0.0; D = 5.0. P is 5 km due east of R (dashed line in the figure).

Trap: swapping sine and cosine (measuring the bearing from east) gives , : the right 5 km in the wrong direction, not an option. Option (D) assumes the four equal legs close back on R; they do not, because the bearings are not apart in turn.

Where this shows up in industry

Latitudes and departures are how a total station traverse is computed: the legs are summed, the misclosure is spread by the Bowditch or transit rule, and the adjusted coordinates go into the CAD and GIS files used for setting out.

GATE 2024 · CE1 · Q.25MCQ · 1 markDistance, angles, traversing and triangulation

When a closed traverse goes from three sides to four, how much does the sum of its interior angles increase?

If the number of sides resulting in a closed traverse is increased from three to four, the sum of the interior angles increases by

  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (B) Official key: B

  1. A closed traverse is a polygon. Its interior angles must add up to , the check used to find the angular misclosure in the field.
  2. Three sides: .
  3. Four sides: .
  4. Increase: . Every extra side adds one more triangle, so (B) .

Trap: (D) is the total for a four-sided traverse, and also the sum of the exterior (deflection) angles of any closed traverse, which stays whatever the number of sides.

Where this shows up in industry

On a closed total station traverse the surveyor sums the observed interior angles, compares them with (n - 2) x 180 degrees, and spreads the angular misclosure across the stations before computing coordinates.

GATE 2024 · CE1 · Q.26MCQ · 1 markDistance, angles, traversing and triangulation

A theodolite reads a zenith angle of 93 degrees 00 minutes 00 seconds: what is the vertical angle?

A surveyor observes a zenith angle of during a theodolite survey. The corresponding vertical angle is

  1. (A)
  2. (B)
  3. (C)
  4. (D)

Answer: (A) Official key: A

  1. A zenith angle is measured down from the vertical (the zenith); a vertical angle is measured up or down from the horizontal, positive for elevation and negative for depression.
  2. So .
  3. : the line of sight points below the horizontal, an angle of depression.
  4. Answer: (A) .

Trap: (B) has the right size but the wrong sign; a zenith angle above always means the target is below the instrument. (C) and (D) use , which is the nadir angle, not the vertical angle.

Where this shows up in industry

Modern total stations display zenith angles by default; the instrument then works out the height difference as slope distance x cos z for trigonometric levelling, so getting the sign convention right decides whether a point is above or below the instrument.

GATE 2024 · CE1 · Q.27MCQ · 1 markDistance, angles, traversing and triangulation

Fundamental lines of a transit theodolite: which relation between the axes is correct?

Among the following statements relating the fundamental lines of a transit theodolite, which one is CORRECT?

  1. (A)The line of collimation must be perpendicular to the horizontal axis at its intersection with the vertical axis.
  2. (B)The axis of altitude level must be perpendicular to the line of collimation.
  3. (C)The axis of plate level must lie in a plane parallel to the vertical axis.
  4. (D)The Vernier of vertical circle must read zero when the line of collimation is vertical.

Answer: (A) The line of collimation must be perpendicular to the horizontal axis at its intersection with the vertical axis. Official key: A

  1. (A) Correct. If the line of collimation is square to the horizontal (trunnion) axis, the telescope sweeps a vertical plane when it is transited; otherwise it traces a cone and the horizontal angles carry a collimation error.
  2. (B) Wrong. The axis of the altitude (telescope) level must be parallel to the line of collimation, so that a centred bubble means a horizontal line of sight.
  3. (C) Wrong. The axis of the plate level must be perpendicular to the vertical axis, so that centring the plate bubble makes the vertical axis truly vertical.
  4. (D) Wrong. The vertical circle vernier must read zero when the line of collimation is horizontal, otherwise every vertical angle carries an index error.
  5. Answer: (A).

Trap: (B), (C) and (D) are each one word away from a real permanent adjustment, swapping parallel and perpendicular or horizontal and vertical. Remember the pattern: levels square to the axis they set, telescope bubble parallel to the sight line.

Where this shows up in industry

Field crews still run these checks: a two-face observation (face left, face right) cancels collimation and index errors, and total stations store electronic collimation and index corrections from a routine calibration.

GATE 2024 · CE2 · Q.31MCQ · 1 markDistance, angles, traversing and triangulation

Match bubble tube, plumb bob, tangent screw and stadia cross-wire to the survey operations they serve

What is the CORRECT match between the survey instruments/parts of instruments shown in the table and the operations carried out with them?

Instruments/Parts of instrumentsOperations
P - Bubble tubei - Tacheometry
Q - Plumb bobii - Minor movements
R - Tangent screwiii - Centering
S - Stadia cross-wireiv - Levelling
  1. (A)P-ii, Q-iii, R-iv, S-i
  2. (B)P-iv, Q-iii, R-ii, S-i
  3. (C)P-i, Q-iii, R-ii, S-iv
  4. (D)P-iii, Q-iv, R-i, S-ii

Answer: (B) P-iv, Q-iii, R-ii, S-i Official key: B

  1. P, bubble tube: the bubble is centred to make the instrument axis truly vertical or the line of sight horizontal, so it is used for levelling (iv).
  2. Q, plumb bob: it hangs from the instrument's vertical axis directly over the station mark, so it is used for centering (iii).
  3. R, tangent screw: after a clamp is tightened, it gives the slow, fine rotation needed to bring the cross-hair exactly on target, the minor movements (ii).
  4. S, stadia cross-wires: the two extra horizontal hairs give a staff intercept ; distance (usually , ), which is tacheometry (i).
  5. Answer: (B) P-iv, Q-iii, R-ii, S-i.

Trap: every option except (D) gets Q-iii right, so the plumb bob does not separate them. Fix the bubble tube first: it levels, it does not move anything, which rules out (A) and (C).

Where this shows up in industry

A total station keeps the same functions in electronic form: an electronic bubble and tilt compensator for levelling, a laser plummet in place of the plumb bob, and fine-motion drives replacing tangent screws.

GATE 2024 · CE2 · Q.64NAT · 2 marksDistance, angles, traversing and triangulation

Length of the closing line RP of a walk P to Q at 30 degrees and Q to R at 90 degrees, 4 m each

A child walks on a level surface from point P to point Q at a bearing of , from point Q to point R at a bearing of and then directly returns to the starting point P at a bearing of . The straight-line paths PQ and QR are 4 m each. Assuming that all bearings are measured from the magnetic north in degrees, the straight-line path length RP (in meters) is ______ (rounded off to the nearest integer).

Answer: 7 m Official key: 6 to 8

  1. Treat it as a traverse. Latitude , departure with the whole circle bearing.
  2. PQ: latitude , departure . QR: latitude , departure .
  3. R relative to P: , , so .
  4. Check: the bearing of R to P is , as given. The interior angle at Q is , and the cosine rule gives the same 6.928 m.
  5. Answer: 7 m (key 6 to 8).

Trap: taking the change of bearing as the angle at Q gives an equilateral triangle and 4 m; assuming a right angle at Q gives 5.66 m. Both fall outside the key.

Where this shows up in industry

Every total station and GNSS controller does this computation in the background: it converts bearings and distances into northings and eastings, so a missing line of a traverse or the distance between two set-out points is a coordinate subtraction.

GATE 2025 · CE1 · Q.27MCQ · 1 markDistance, angles, traversing and triangulation

How do you convert the quadrantal bearing N30W to a whole circle bearing?

If the quadrantal bearing of a line is N30°W, then the whole circle bearing of the line is

  1. (A)120°
  2. (B)210°
  3. (C)300°
  4. (D)330°

Answer: (D) 330° Official key: D

  1. A whole circle bearing (WCB) is measured clockwise from north, from to . A quadrantal bearing (reduced bearing) is measured from north or south, towards east or west, from to .
  2. N30°W means: face north, turn towards west. That line lies in the north-west quadrant, between WCB and .
  3. Measured clockwise from north it is short of a full turn: .
  4. Rules for the four quadrants: NE , SE , SW , NW .
  5. The answer is , option (D).

Trap: (C) measures the from west instead of from north (), and (B) is the bearing of S30°W, the line pointing the other way round the south.

Where this shows up in industry

Total stations and GNSS controllers record directions as whole circle bearings (azimuths), while older title deeds and some field books still give quadrantal bearings such as N30W. Converting between the two without a quadrant slip is a routine step when re-establishing old boundary lines.

GATE 2025 · CE2 · Q.65NAT · 2 marksDistance, angles, traversing and triangulation

Interior angle ABC from the fore bearings of AB (60 degrees) and BC (122 degrees)

If the Fore Bearing of the lines AB and BC are 60° and 122°, respectively, then the interior angle ∠ABC (in degrees) is ______ (round off to the nearest integer).

Answer: 118 degrees Official key: 118 to 118

  1. At B the two arms of the angle are BA and BC. The direction of BA is the back bearing of AB: .
  2. The direction of BC is its fore bearing, .
  3. Angle between them: . It is less than , so it is the interior angle; the other side of the corner is .
  4. Check with the deflection angle: the line turns to the right at B, and the interior angle is .
  5. ∠ABC .

Trap: is the deflection angle (the change of direction), not the angle between the two lines; is the exterior angle.

Where this shows up in industry

In a compass or total station traverse the included angles are computed from bearings like this, then summed and checked against (2n minus 4) right angles for a closed traverse. A misclosure larger than the allowed limit sends the crew back to re-observe.

GATE 2026 · CE1 · Q.20MCQ · 1 markDistance, angles, traversing and triangulation

Latitude and departure of a 100 m line AB with a whole circle bearing of 150 degrees

The Whole Circle Bearing (WCB) of line AB is . The length of AB is 100 m. The latitude and departure values, respectively, for this line are:

  1. (A)+86.60 ; +50.00
  2. (B)+86.60 ; −50.00
  3. (C)−86.60 ; +50.00
  4. (D)−86.60 ; −50.00

Answer: (C) −86.60 ; +50.00 Official key: C

  1. Latitude is the projection of the line on the north-south meridian, ; departure is the projection on the east-west line, , with the whole circle bearing.
  2. A WCB of lies between and : the line points south-east (reduced bearing S 30° E), so latitude is negative (southing) and departure positive (easting).
  3. Latitude m; departure m.
  4. Answer (C).

Trap: taking the magnitudes from the reduced bearing (S 30° E) but the signs of the north-east quadrant gives (A); flipping both signs is option (B). The quadrant fixes the signs: south is negative latitude, east is positive departure.

Where this shows up in industry

A total station reports every traverse leg as a northing and easting increment computed exactly this way; survey software then sums them to find the closing error of the traverse and adjusts it, for example by the Bowditch rule, before plotting coordinates.

GATE 2026 · CE1 · Q.34NAT · 1 markDistance, angles, traversing and triangulation

Temperature correction for a 200 m line measured with a 30 m tape standardised at 25 C and used at 35 C

A 30 m long tape is standardized at . It was used to measure the length of a line which came out to be 200 m. The temperature during the measurement was . The coefficient of expansion of the tape was per . The correction in the measured length (in mm) due to change in temperature is ______ (in integer).

Answer: 22 mm Official key: 22 to 22

  1. The temperature correction is , where is the measured length of the line, not the length of the tape.
  2. .
  3. m.
  4. At 35 °C the tape is longer than its nominal 30 m, so each tape length laid out covers more ground than recorded: the measured length is too short and the correction is positive, +22 mm.
  5. Answer 22 mm.

Trap: using the 30 m tape length in place of the 200 m line gives 3.3 mm (3), outside the key.

Where this shows up in industry

A steel tape is standardised at a stated temperature and pull. On a hot site 15 degrees above that, a 30 m steel tape is about 5 mm long per length, so careful taping logs temperature; total stations apply the equivalent atmospheric (temperature and pressure) correction to EDM distances in parts per million.

GATE 2026 · CE2 · Q.62NAT · 2 marksDistance, angles, traversing and triangulation

What is the total angular error of a closed four-sided traverse ABCDA from its measured interior angles?

Interior angles measured at the locations of a closed traverse ABCDA are given in table below.

LocationInterior angle
A
B
C
D

The total error in the measured angles (in degrees) is ______ (rounded off to three decimal places).

Answer: 0.182 degrees Official key: 0.180 to 0.184

  1. For a closed traverse of sides the interior angles should add up to ; for that is .
  2. Seconds: . Minutes: . Degrees: .
  3. Sum , so the error is .
  4. In degrees: .
  5. Answer 0.182° (the angles add up to too much).

Trap: writing as gives 0.176°, and dividing by the four angles gives the correction per angle, 0.045°; both are outside the key.

Where this shows up in industry

On a real traverse the angular misclosure is compared with an allowable limit that grows with the square root of the number of stations, then shared equally among the angles before bearings and coordinates are computed; a misclosure near 11 minutes would mean re-observing the angles.

GATE 2022 · CE1 · Q.23MCQ · 1 markPhotogrammetry, remote sensing and GIS

Scale of a vertical aerial photograph: flying height 3.5 km above MSL, focal length 152 mm, ground at 460 m

An aerial photograph is taken from a flight at a height of 3.5 km above mean sea level, using a camera of focal length 152 mm. If the average ground elevation is 460 m above mean sea level, then the scale of the photograph is

  1. (A)1 : 20000
  2. (B)1 : 20
  3. (C)1 : 100000
  4. (D)1 : 2800

Answer: (A) 1 : 20000 Official key: A

  1. For a vertical photograph the scale is focal length over the camera's height above the ground being photographed: .
  2. Put both lengths in metres: m, m.
  3. .
  4. Answer: (A) 1 : 20000.

Trap: leaving in millimetres gives , option (B). Using the height above mean sea level and ignoring the ground elevation gives 1 : 23026, a smaller scale than the photograph really has over this terrain.

Where this shows up in industry

Drone and aircraft mapping flights are planned the same way: the pilot picks the height above ground that gives the required photo scale or ground sample distance for the camera, and hilly terrain changes the scale across a single image, which is why photogrammetry software needs a terrain model.

GATE 2022 · CE2 · Q.23MCQ · 1 markPhotogrammetry, remote sensing and GIS

Match city attributes (temperature, name, population density, ease-of-business rank) with their scale of measurement

Match the following attributes of a city with the appropriate scale of measurements.

AttributeScale of measurement
(P) Average temperature (°C) of a city(I) Interval
(Q) Name of a city(II) Ordinal
(R) Population density of a city(III) Nominal
(S) Ranking of a city based on ease of business(IV) Ratio

Which one of the following combinations is correct?

  1. (A)(P)-(I), (Q)-(III), (R)-(IV), (S)-(II)
  2. (B)(P)-(II), (Q)-(I), (R)-(IV), (S)-(III)
  3. (C)(P)-(II), (Q)-(III), (R)-(IV), (S)-(I)
  4. (D)(P)-(I), (Q)-(II), (R)-(III), (S)-(IV)

Answer: (A) (P)-(I), (Q)-(III), (R)-(IV), (S)-(II) Official key: A

  1. The four levels (Stevens' scales, used to classify GIS attribute data) add one property each: nominal = labels only; ordinal = order; interval = order plus equal steps; ratio = equal steps plus a true zero.
  2. (Q) A city's name is a label with no order: nominal.
  3. (S) A rank tells you which city is ahead, not by how much: ordinal.
  4. (P) Temperature in °C has equal steps, but 0°C is not zero heat, so 30°C is not twice 15°C: interval.
  5. (R) Population density has a true zero (no people), so one city can be twice as dense as another: ratio.
  6. Answer: (A).

Trap: calling temperature ratio because it is a measured number. Only kelvin has a true zero; in °C the ratio of two temperatures means nothing.

Where this shows up in industry

In QGIS or ArcGIS the level of an attribute decides what you may do with it: nominal fields get categorised colours, ranks can be sorted but not averaged, and only ratio fields such as density can be divided, normalised or shown as graduated maps.

GATE 2023 · CE1 · Q.23MCQ · 1 markPhotogrammetry, remote sensing and GIS

Percentage reduction in pixels when a 10 inch by 10 inch raster scan drops from 600 dpi to 300 dpi

A student is scanning his 10 inch × 10 inch certificate at 600 dots per inch (dpi) to convert it to raster. What is the percentage reduction in number of pixels if the same certificate is scanned at 300 dpi?

  1. (A)62
  2. (B)88
  3. (C)75
  4. (D)50

Answer: (C) 75 Official key: C

  1. Resolution in dpi applies along both directions of the sheet, so the pixel count is (width dpi) (height dpi).
  2. At 600 dpi: pixels.
  3. At 300 dpi: pixels, a quarter of the first.
  4. Reduction : (C) 75.
  5. In general, scaling the resolution by scales the pixel count by ; here , so .

Trap: answering 50 % (option D) by halving the count in one direction only. The dpi halves along both edges of a raster grid, so the count drops four-fold, and so does the file size before compression.

Where this shows up in industry

The same square law governs GIS rasters: a drone orthomosaic or DEM at 5 cm cell size holds four times the cells of the same area at 10 cm, which is why mapping teams pick the coarsest ground sample distance the deliverable allows.

GATE 2023 · CE2 · Q.35NAT · 1 markPhotogrammetry, remote sensing and GIS

Scale of a vertical aerial photograph covering 6 km by 3 km of ground on a 30 cm by 15 cm print

If the size of the ground area is 6 km × 3 km and the corresponding photo size in the aerial photograph is 30 cm × 15 cm, then the scale of the photograph is 1 : ______ (in integer).

Answer: 1 : 20000 Official key: 20000 to 20000

  1. Photo scale is a ratio of lengths: photo distance / ground distance, both in the same unit, written as .
  2. Along the long side: 6 km cm, shown as 30 cm, so .
  3. Along the short side: , the same, so the photo is uniformly scaled (a vertical photo of flat ground).
  4. Scale = 1 : 20000.
  5. For a camera of focal length at height above flat ground, ; a 152 mm camera would be flying at about m.

Trap: dividing the areas ( by ) gives 400000000, the square of the scale number; leaving 6 km as 6000 m against 30 cm gives 200. Convert to one unit and use lengths.

Where this shows up in industry

Photo scale drives the flight plan: flying height is focal length times the scale number, and it sets ground coverage per frame. Drone mapping apps do the same sum when they turn a target ground sample distance into a flying height.

GATE 2024 · CE2 · Q.30MCQ · 1 markPhotogrammetry, remote sensing and GIS

Focal length for vertical aerial photographs at 1:13000, flying height 3000 m, terrain at 1050 m

For a reconnaissance survey, it is necessary to obtain vertical aerial photographs of a terrain at an average scale of 1: 13000 using a camera. If the permissible flying height is assumed as 3000 m above a datum and the average terrain elevation is 1050 m above the datum, the required focal length (in mm) of the camera is

  1. (A)100
  2. (B)150
  3. (C)125
  4. (D)200

Answer: (B) 150 Official key: B

  1. The scale of a vertical photograph over ground at elevation is , with the flying height above the same datum.
  2. Height of the camera above the terrain: .
  3. .
  4. Answer: (B) 150.

Trap: using the flying height above datum, , gives 230.8 mm; the scale depends on the height above the ground being photographed, so the terrain elevation must come off first. A 150 mm lens is in fact the standard wide-angle focal length of film-era mapping cameras.

Where this shows up in industry

Drone mapping uses the same relation in the form of ground sampling distance: pixel size x flying height above ground / focal length, which is why flight-planning apps raise the drone over high ground to keep the resolution constant.

From GATE prep to a surveying and civil design career

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.