Car hood and back door design calculator: head impact zones (WAD), hinge axis and latch trajectory
A bonnet's child head area runs from WAD 1 000 to 1 700 mm in UN R127 and GTR 9; the adult area runs on to 2 500 mm (R127 04 series) or 2 100 mm (GTR 9, AIS-100). Euro NCAP tests the child headform from 1 000 to 1 500. The latch arc is centred at the foot of the perpendicular from the striker onto the hinge axis, which matches the axis midpoint only for a centred striker.
Enter a centreline side profile and the calculator draws the taut WAD tape, the 1 000 mm straight edge at 50° and the 165 mm sphere, gives each document's zones side by side and checks the crush space under the bonnet. The second tab finds the hinge axis, the latch trajectory and the opening sweep for a hood or a back door. Built for the hood and back door challenges of Skill-Lync's Automotive Sheet Metal Design course. Skill-Lync read 3,160 public reports: 517 draw the latch circle from the axis midpoint and none computes a WAD. Free, runs in your browser.
UN R127 04 series Suppl. 2 · UN GTR 9 + Amend. 2 · Euro NCAP VRU v1.2 · AIS-100 Rev.1 · EU 2003/102, 78/2009, 631/2009, 2019/2144 · checked against a separate solution (7,199 checks at build) · Updated 22 Nov 2026
An illustrative sedan profile: low bonnet leading edge, long bonnet, the rear edge of the bonnet above the windscreen line. Not a real car: edit the points or the depths to your own section.
Hinges near the cowl at x = 1 220 mm, latch striker at the front centre. Symmetric hinges and a centre latch: the midpoint of the hinge axis is also the foot of the perpendicular, so the course's midpoint rule gives the right circle here.
Says which document each number belongs to, its current value, and the fix.
- Bonnet leading edge: contact at x = 110, z = 720 mm (BLE height), WAD 748.9 mm.
- Bonnet rear reference point: the 165 mm sphere first touches at x = 1,250, z = 935 mm, WAD 1,913.5 mm, on the bonnet. The bonnet's rear edge is at WAD 1,913.5 mm.
- Pop-up bonnet: about 1.7 mm of lift (vertical) at the worst station to reach the half-sine space plus the stack. A real bonnet needs more: the skin buckles, the head can hit a second time, and the pulse is never ideal.
What 3,160 reports say
- 1,190 of 1,686 hood reports discuss pedestrian protection, 496 mention WAD, 0 compute one for their own hood.
- Child zone 1 000 to 1 500 in 37, 1 000 to 1 700 in 85; adult 1 500 to 2 100 in 34, 1 700 to 2 100 in 75.
- 10 name UN R127 or GTR 9; 40 km/h in 176, 35 km/h in 1.
- Latch circle from the axis midpoint: 360 hood and 157 back door reports; from the foot of the perpendicular: 0.
- 1,388 back door reports mention gas stays; 0 give a stay force in N (gas strut calculator).
As of 22 Nov 2026, n = 1,686 hood + 1,474 back door public reports with text. Skill-Lync's own data, a starting point, not a grade.
Head areas along the centreline, by document
| Document | Child headform, WAD (mm) | Adult headform, WAD (mm) | Note |
|---|---|---|---|
| UN R127 (04 series) | 1,000 to 1,700 | 1,700 to 1,831 | — |
| UN GTR 9, AIS-100 (Rev.1), EU 631/2009 | 1,000 to 1,700 | 1,700 to 1,831 | — |
| Euro NCAP VRU protocol v1.2 | 1,000 to 1,700 | 1,700 to 2,500 | child/small adult headform up to WAD 1,700 (BRRL behind 1 700) |
Crush space at each station
| WAD | Headform | Slope β | Gap | 1-D, full speed | Along the line | Normal only | Need (half-sine + stack) | Verdict |
|---|---|---|---|---|---|---|---|---|
| 1,100 | child 3.5 kg, 50° | 10.6° | 75 | 47.6 / 56.2 | 41.5 / 49.0 | 33.0 / 38.9 | 55.5 | enough |
| 1,300 | child 3.5 kg, 50° | 10.6° | 62 | 47.6 / 56.2 | 41.5 / 49.0 | 33.0 / 38.9 | 55.5 | enough |
| 1,500 | child 3.5 kg, 50° | 6.3° | 80 | 47.6 / 56.2 | 39.6 / 46.8 | 29.1 / 34.4 | 53.3 | enough |
| 1,700 | child 3.5 kg, 50° | 6.3° | 52 | 47.6 / 56.2 | 39.6 / 46.8 | 29.1 / 34.4 | 53.3 | tight |
| 1,800 | adult 4.5 kg, 65° | 6.3° | 58 | 47.6 / 56.2 | 45.1 / 53.2 | 41.2 / 48.6 | 59.7 | tight |
Depths in mm, normal to the bonnet skin, square / half-sine pulse, HIC 1,000, 9.7 m/s. Stack = 6.5 mm.
What is the wrap around distance (WAD), and why is it a taut tape?
WAD is where a pedestrian's head lands, measured on the car. UN R127 (2.43) defines it as the trace of the end of a flexible tape held in a vertical longitudinal plane, taut, with one end on the ground vertically below the front face of the bumper and the other on the front structure, car at its normal ride attitude. A taut tape does not follow the surface into hollows: it takes the shortest path over the car, which is the upper convex hull of the profile up to the point:
Qk are the hull corners between the ground point and P. On a convex bonnet the tape lies on the skin, so the WAD grows by the arc length; across the cowl gap it bridges straight to the windscreen. Euro NCAP (2.2.5.6) says the same in words: where a WAD falls below the outer contour, approximate the contour and project down. For the default sedan the vertices sit at WAD 193, 430, 602, 749, 1,003, 1,410, 1,913, 1,950, 1,969, 2,827, 3,278 mm.
How are the bonnet leading edge and rear reference lines found?
Leading edge (BLE). A 1 000 mm straight edge, parallel to the car's centre plane, inclined rearwards 50° from the vertical, its lower end 600 mm above the ground, is moved onto the front (R127 2.7, Euro NCAP 2.2.2). In a side section that is a minimum: the first point it touches is the one with the smallest shift a.
If the bottom end touches first, that contact is the BLE. If the top end touches first, as on the steep MPV preset, WAD 1 000 is used. If the bonnet top is itself at 50°, so the edge lies along it, the edge is set at 40°. The BLE height is the ground-to-BLE height (720 mm for the sedan, at WAD 748.9 mm).
Rear (BRRL). A 165 mm sphere is rolled across the front structure while it keeps touching the windscreen, wipers removed; the most rearward contact points form the line (R127 2.8, Euro NCAP 2.2.3). In the section the sphere is a circle of radius 82.5 mm sliding down the windscreen until it first touches the bonnet. For the sedan that is x = 1,250, z = 935 mm, WAD 1,913.5 mm. If the sphere reaches the cowl or the windscreen base instead, the BRRL is not on the bonnet; R127 then uses the bonnet's rear edge when the line 82.5 mm ahead of the BRRL is behind WAD 2 100 (2.1, footnote 3).
Where are the child and adult head impact zones on a bonnet?
Between WAD 1 000 and 1 700 mm for the child headform, and from 1 700 mm rearwards for the adult, in every regulation read for this page. The rear bound and the 82.5 mm offsets differ:
| Document | Child / small adult headform | Adult headform | Speed, angle, mass | HIC |
|---|---|---|---|---|
| UN R127, 04 series, Supplement 2 (2025) | WAD 1 000 (or BLE + 82.5) to 1 700 (or BRRL − 82.5) | WAD 1 700 (or BLE + 82.5) to 2 500 (or BRRL − 82.5); 2 100 as a transitional option | 9.7 m/s; 50°, 3.5 kg; 65°, 4.5 kg | ≤ 1 000 on ½ of the child area and ⅔ of the bonnet top, ≤ 1 700 elsewhere |
| UN GTR 9 (2009, Amend. 2 2019), AIS-100 Rev.1 (2024) | WAD 1 000 to 1 700, 82.5 mm from BLE / BRRL | WAD 1 700 to 2 100, 82.5 mm from BRRL | 9.7 m/s; 50°, 3.5 kg; 65°, 4.5 kg | ≤ 1 000 on ½ of the child area and ⅔ of the combined areas, ≤ 1 700 elsewhere |
| Euro NCAP VRU protocol v1.2 (2026) | WAD 1 000 to 1 500; to the BRRL if it is between 1 500 and 1 700; to 1 700 if it is behind | Rearward of that, to WAD 2 500 (windscreen and roof included) | 11.1 m/s; 50° (20° ahead of the BLE); 65° | Colour bands per 100 mm grid point: green < 650 to red ≥ 1 700 |
| EU Regulation 78/2009 with 631/2009 (repealed by 2019/2144 from 6 July 2022) | WAD 1 000 to 1 700, 82.5 mm from BLE / BRRL | WAD 1 700 to 2 100 | 35 km/h; 3.5 kg; 4.5 kg | HPC ≤ 1 000 on ½ child and ⅔ overall, ≤ 1 700 rest |
| Directive 2003/102/EC phase 1 (replaced) | "bonnet test area" (zones in Decision 2004/90/EC, not read) | 35 km/h; 3.5 kg child; 4.8 kg adult to the windscreen (monitoring) | HPC ≤ 1 000 on ⅔, ≤ 2 000 on ⅓ | |
So "child 1 000 to 1 500" is Euro NCAP's number, "child 1 000 to 1 700" the regulations', "adult 1 700 to 2 100" GTR 9's and AIS-100's, and "adult 1 500 to 2 100" none of them. EU type approval has used UN R127 since Regulation (EU) 2019/2144 (Annex II, B1), which also asks for the enlarged head zone to WAD 2 500 (B2). We could not check the CMVR notification that makes AIS-100 mandatory in India.
How much space does a bonnet need above the engine for HIC 1 000?
At least 47.6 mm at 9.7 m/s, and only if the head could be stopped at a perfectly constant deceleration. With an ideal pulse of shape constant c and area factor k (square 1 and 1; half-sine 0.4146 and 2/π), the head stops in time T over a distance d:
A half-sine pulse needs 56.2 mm; HIC 1 700 with a square pulse 33.4 mm; Euro NCAP's 11.1 m/s at HIC 1 000 68.2 mm. The head arrives at 50° or 65° to the horizontal on a bonnet sloping at β, so the calculator gives three depths normal to the skin:
"Enough" means the gap covers the half-sine depth along the line plus the panel stack (outer 0.75 + inner 0.75 + about 5 mm mastic in the course data); "tight" means it covers only the square-pulse, normal-only bound. Treat both as first checks. A real bonnet needs more: the skin buckles, the head can strike the hard point a second time, and no pulse is ideal. The pulse maths is the same as Skill-Lync's HIC calculator. The pop-up figure is the vertical lift an active bonnet would need to reach the "enough" depth at the worst station.
How do you find the latch trajectory for a hood or back door?
The striker turns about the hinge axis, so its path is a circle in the plane through the striker normal to the axis. The centre is the foot F of the perpendicular from the striker S onto the axis, and the striker moves along the tangent:
Many reports draw the circle from the midpoint M of the hinge axis instead. The two points differ by the striker's offset along the axis:
With mirror-image hinges and a centre latch, the offset is zero and the midpoint rule is right. In the side view it also stays right for an offset latch, as long as the axis runs exactly across the car. It goes wrong when the hinges sit at different heights or one sits further forward, and the latch is off centre: then the side-view circle from M is not the striker's path. The calculator sweeps the panel with the Rodrigues rotation about the axis and measures every edge point against every body point:
For a hood, watch the rear edge diving towards the cowl and windscreen as it opens. For a back door, check its lower edge height at full open against a head height you choose (no standard number is used here), and the luggage opening above the sill. The stay force is a separate job: use the gas strut calculator.
Worked example: the default sedan and hood
The sedan preset's bonnet leading edge, rear reference point and R127 areas, then the hood preset's latch arc and the offset back door's midpoint error:
The straight edge touches the sedan at its bonnet corner, x = 110 mm; the sphere stops on the bonnet's rear edge. Euro NCAP gives the same car a child zone of 1,000 to 1,700 and an adult zone of 1,700 to 2,500 mm, because it tests the windscreen to WAD 2 500 and uses no 82.5 mm offsets. GTR 9 gives 1,700 to 1,831.0 mm for the adult. The hood latch should close 10.3° off vertical, towards the rear.
What do 3,160 hood and back door reports say?
Skill-Lync read the public "Hood design" and "Design of backdoor" reports on 22 Nov 2026: 1,686 hood and 1,474 back door reports with text (of 1,763 and 1,549 public).
| The report says | Reports | Examples |
|---|---|---|
| Child zone WAD 1 000 to 1 500 (Euro NCAP) | 37 | 1, 2, 3 |
| Child zone WAD 1 000 to 1 700 (R127, GTR 9, AIS-100) | 85 | 1, 2, 3 |
| Adult zone WAD 1 500 to 2 100 (no document) | 34 | 1, 2, 3 |
| Adult zone WAD 1 700 to 2 100 (GTR 9, AIS-100) | 75 | — |
| Impact speed 40 km/h / 35 km/h | 176 / 1 | 1, 2, 3 |
| Hood latch circle from the hinge axis midpoint or centre | 360 | 1, 2, 3 |
| Back door latch circle from the axis midpoint or centre | 157 | 1, 2, 3 |
| Latch circle from the foot of the perpendicular | 0 | — |
- WAD. 496 hood reports mention WAD and 1,190 discuss pedestrian protection, but 0 compute a WAD for their own hood: every WAD in the corpus is a zone bound (2 100 in 93, 1 700 in 83, 1 000 in 35, 1 500 in 24).
- Documents. 10 name UN R127 or GTR 9; 2003/102/EC, 78/2009 and AIS-100 are named in 1, 1 and 1 report each. 473 mention Euro NCAP, mostly as general text without the protocol's numbers.
- Tangency. 782 hood reports mention the striker being tangent (or perpendicular) to the trajectory circle; 0 place that circle's centre at the foot of the perpendicular.
- Back door. 597 mention the hinge axis and 1,388 gas stays; 0 give a stay force in N.
Counts as of 22 Nov 2026, n = 1,686 + 1,474 public reports with at least 900 characters of text, de-duplicated. Skill-Lync's own data, a starting point, not a grade. Text inside images is not counted.
- Child zone WAD 1 000 to 1 500 is Euro NCAP's (VRU protocol v1.2, 2.2.5.9): child/small adult headform from WAD 1 000 up to and including 1 500, then up to the BRRL or 1 700 depending on where the BRRL is (37 public reports write this). Say "Euro NCAP" next to it; the regulations use 1 000 to 1 700.
- Adult zone WAD 1 500 to 2 100 is in none of the documents: it mixes Euro NCAP's 1 500 child limit with GTR 9's 2 100 adult limit (34 public reports write this). GTR 9 / AIS-100: 1 700 to 2 100. R127 04 series and Euro NCAP: 1 700 to 2 500.
- Together, 1 000 to 1 500 and 1 500 to 2 100 put a boundary at 1 500 that only Euro NCAP has, and a rear bound at 2 100 that Euro NCAP does not have. Pick one document and use all its numbers.
- "HIC 1 000 in zone A, 1 700 in zone B" is right only with the fractions: the maker marks the HIC 1 000 and 1 700 zones (GTR 9 5.2.4), and the 1 000 zone must cover at least half of the child area and two thirds of the whole bonnet top test area.
- 40 km/h is the car speed the tests represent. The headform is fired at 35 km/h (9.7 m/s, R127 Annex 5 4.6, GTR 9 7.3.4) in the regulations and at 11.1 m/s (40 km/h) in Euro NCAP (3.4.2.21) (176 public reports write this). Say which.
- BLE reference line: a 1 000 mm straight edge, 50° rearward from the vertical, lower end 600 mm above the ground (R127 2.7, Euro NCAP 2.2.2). If its top end touches first, WAD 1 000 is used; if the bonnet is itself at 50°, use 40°.
- A circle from the midpoint of the hinge axis is right only when the striker lies in the plane through that midpoint normal to the axis (symmetric hinges and a centre latch). In general the centre is the foot of the perpendicular from the striker onto the axis (360 public reports write this). Tab 2 shows the error for an offset latch.
- Name the document beside each number (UN R127 04 series, GTR 9, Euro NCAP VRU protocol v1.2, AIS-100 Rev.1). The numbers differ between them; without the name a reader cannot check yours.
What this calculator does not cover
- 3D surfaces and the grid. It works on one centreline section. Real zones are traced across the width with the side reference lines (a 700 mm straight edge inclined inwards 45°, R127 2.32) and the corner reference points; Euro NCAP marks a 100 mm grid.
- A real HIC. The crush depths come from ideal pulses. Only a test or an LS-DYNA headform simulation gives the HIC of a real bonnet.
- Hinge kinematics beyond a fixed axis. Four-bar (goose-neck) hood hinges and pop-up actuators move the axis; this assumes a single fixed pivot line.
- India's CMVR notification for AIS-100: not checked. AIS-100 Rev.1's own text was read.
The hood and back door challenges are part of Skill-Lync's Automotive Sheet Metal Design course: class-A surfaces to inner panels, reinforcements, hemming, latch and hinge layout.
Frequently asked questions
What is the wrap around distance (WAD) on a car?
WAD is the length of a flexible tape held taut in a vertical fore-aft plane, from the ground below the bumper's front face over the front of the car to a point on its surface (UN R127 2.43). Because the tape is taut, it bridges hollows such as the gap at the cowl instead of following them.
What are the child and adult head impact zones on a bonnet?
In UN R127 and GTR 9 the child headform area runs from WAD 1 000 to 1 700 mm. The adult area runs to 2 100 mm in GTR 9 and AIS-100, or to 2 500 mm in R127's 04 series. Euro NCAP v1.2 tests the child headform from 1 000 to 1 500 mm, extended to 1 700 depending on the BRRL.
How is the bonnet leading edge reference line found?
Hold a 1 000 mm straight edge parallel to the car's centre plane, inclined rearwards 50° from the vertical with its lower end 600 mm above the ground, and move it onto the front. Its contact points form the line. If its top end touches first, the WAD 1 000 line is used instead (UN R127 2.7).
What speed and angle are used for the pedestrian headform test?
UN R127, GTR 9 and AIS-100 fire the headform at 9.7 m/s (35 km/h): the 3.5 kg child headform at 50° to the horizontal and the 4.5 kg adult at 65°. Euro NCAP uses 11.1 m/s (40 km/h), the same angles, and 20° for child points on or ahead of the bonnet leading edge.
How much space under the bonnet is needed for HIC 1 000?
Stopping a head from 9.7 m/s at a constant deceleration within HIC 1 000 takes 47.6 mm, the absolute lower bound; a half-sine pulse needs 56.2 mm. Add the panel stack. Real bonnets need more, because the skin buckles, the head can strike twice and no pulse is ideal.
Where is the centre of the hood latch trajectory circle?
At the foot of the perpendicular from the striker onto the hinge axis, the line through both hinge pivots. The radius is the distance from the striker to that point and the striker moves along the tangent. The axis midpoint gives the same centre only when the striker lies in the plane through the midpoint normal to the axis.
Related on Skill-Lync
- Gas strut calculator: the stay force for a tailgate, hood or lid
- Head injury criterion (HIC) calculator: HIC15 from a headform curve, Euro NCAP bands
- Wheel arch clearance calculator: the EU 30°/50° wheel guard rule
- Vehicle benchmarking calculator: steel vs aluminium hood thickness
- BIW design courses compared
- Student project: Hood design-Week 2 and Design of backdoor
- All free engineering tools
Sources
- UN Regulation No 127 (pedestrian safety), EU OJ L 2025/460, 17.3.2025, incorporating Supplement 2 to the 04 series: 2.1, 2.6, 2.7, 2.8, 2.16, 2.18, 2.21, 2.32, 2.43, 2.44, 5.2.1, 5.2.2, 11.19 to 11.23, Annex 4 5.1.1 and 5.3.1, Annex 5 4.6, 4.7, 5.6, 5.7 (EUR-Lex CELEX 42025X0460, read 22 Nov 2026).
- UN GTR No. 9, ECE/TRANS/180/Add.9 (26 Jan 2009): 3.1, 3.12, 3.23, 3.28, 5.2.3, 7.3.2 to 7.4.5, preamble 72; Amendment 2, ECE/TRANS/180/Add.9/Amend.2 (23 Jan 2019). Later amendments not read.
- Euro NCAP, Crash Protection: Vulnerable Road User Impacts Protocol, Version 1.2, July 2026: 2.2.2, 2.2.3, 2.2.5 to 2.2.5.11, 2.2.9, 3.4.2.12 to 3.4.2.21, 4.2.1.1 colour bands.
- Directive 2003/102/EC, Annex I 3.1 and 3.2; Regulation (EC) No 78/2009, Annex I 2 and 3; Regulation (EC) No 631/2009, Annex I test points; Regulation (EU) 2019/2144, Article 18, Article 19, Annex II B1 and B2 (EUR-Lex).
- ARAI, AIS-100 (Rev.1), April 2024: 3.1, 3.15, 5.2.3, 7.3.4.6; AIS-100 (2010).
- Skill-Lync, 3,160 public hood and back door reports, read 22 Nov 2026. scripts/verify/hood.py recomputes every case another way (convex hull and a shortest path for the WAD, a sliding straight edge and a sampled sphere, the zones from the text, the pulse depths in closed form and by brute-force HIC, the hinge with scipy rotations), 815 cases; the page checks itself against it at build (7,199 checks).