Wiring harness design in CATIA V5 - 3D modeling Week 5 & 6 Challenge

RENDERING USING AUTODESK ALIAS   Objective: In this challange, the task is to render some models we did earlier using Autodesk Alias. Rendering is done through switching to the 'Visualize' option available under the control panel.  We can select the whole surface and double click on the material we…

                                DEVELOPMENT OF KIA SPORTAGE USING ALIAS AUTO STUDIO       OBJECTIVE:-                 To build the car using the Curves traced from the given blueprint…

             OBJECTIVE:  To create the surface model of car seat using auto desk alias design.                                INTRODUCTION:-                …

                                                                                           …

                                                                           SIDE FENDER OR SIDE WINGS DESIGN BY USING ALIAS  …

                                                                                           …

       1. Concept Modelling of Alloy Wheel:- 2. Objective :-                               TO Follow the entire process as per the guidelines from Video Tutorial to build the Surfaces for Concept Modelling…

                                                                                           …

                                                                                                  V 16 ENGINE WIRE HARNESS ROUTING                                                project is to route the wiring harness on given Bugatti V16 Engine and prepare flatten view drawing in CATIA V5. All types of packaging rules…

     FLATTEN THE WIRING HARNESS AND DRAFT THE WIRING HARNESS ASSEMBLY   GIVEN BUNDLE CONNECTION:-      WIRE HARNESS ASSEMBLY:-  WIRE HARNESS FLATENING:- WE GO TO THE HARNESS FLATTENING WORKBENCH AND DEFINE THE FLATTENING PARAMETERS. WE USE THE EXTRACT COMMAND TO BRING THE HARNESS…

           The objective of this project is to first route the two Harness A and Harness B as per the given harness layout. The electrical connectors are represented by numbers in the above figure. There are 8 different types of connectors at 10 different locations.      Bundle…

          CAD data of the following Connectors:- DT06-4S DT06-6S DT06-2S DT06-08SA Connectors Layout Design:- PROCEDURE:- Firstly draw as a sketch as per given connection system for only "refrence purpose" and align that locations for connectors Download connectors 3D data from www.te.com…

                                                                                           …

  CONNECTOR DEFINATIONS IN CATIA V5  Deutsch DT06 – 08SA:- Connector connection point:- Create midpoint on the contact face which will be normal to wire bunddle insertion. Craete Axis System with respect to the point which we have created and defining the axis direction as shown below, Bundle connection…

OBJECTIVE:      *To create the thickned part using master section for refference.      *To create the mounting features are per design guidelines in the industry and with master section.      *To perform draft analysis & tooling analysis. INTRODUCTION: The door panel is…

  ASSEMBLY :- Assembly modeling is a technology and method used by computer-aided design and product visualization computer software systems to handle multiple files that represent components within a product. The components within an assembly are represented as solid or surface models.   QUICK RETURN MECHANISM:-…

     PROCEDURE FOR DESIGNING A PILLAR COMPONENT :-              Class A surface: Class A surface is a Styling surface or aesthetic surface get it from the styling team. we will design the plastic component by using the Class A surface as input. Check all the views…

  Draft:-                The draft is the amount of taper for moulded or cast parts perpendicular to the parting. line. Draft angles are a design consideration that makes it much easier for a part to release cleanly from a mould. A draft angle is calculated as a degree measurement…

     CLASS A SURFACE:-                     In Automotive design, a Class A Surface in any of a set of freeform surfaces of high efficiency and quality. Although, strictly, its nothing kore than saying the surfaces have curvature and tangency alignment- to…

    To Create the Core and cavity blocks for the switch bezel component   TOOLING AXIS :-                       The Tooling Direction is basically the direction that the mold pulls a part. The mold is built in two separate pieces, basically. You…

    RIBS:-            Ribs are thin, wall-like features typically designed into the geometry of a part to add internal support to walls or other features like bosses.     SCREW BOSSES:-                    Bosses are small…

   BUMPER:-              Car bumpers feature protruding shrouds of plastic or metal, called bumper covers, that surround energy-absorbing materials. They are designed to absorb impact to the front and rear of vehicles and minimize low-speed collision damage.    …

                                                                                           …

                                                                                           …

           A CLASS SURFACE:-          Given A CLASS SURFACE converts to solid part (b &c ) surfaces by helping Aclass surface           It is an Aesthetic part of component                  …

                  BACK DOOR:-                                                The Back door of a car is a component which hinges at the back of the car to cover…

              ROOF :-                => An automobile roof or car top is the portion of an automobile that sits above the passenger compartment, protecting the vehicle occupants from sun, wind, rain, and other external elements.…

                    FENDER:-         => Fender is an American english term for the part of automobile,the primary purpose is to prevent sand,mud,rocks,liquids& or other road spary  from being thrown into the…

                     INTRODUCTION:-                  The fender wheel arch is basically semi circular part postioned and it is made up of rubber and plastic that can be installed on the front fender  The fender…

                 SECTION MODULUS:-                            Section modulus is the geometric preperty of the crossection of the structure.it is the directly measured the strenth of our given section(or)…

     HOOD INTRODUCTION:- Hood is also called as bonnet,it cover the engine compartment and also to give aesthetic look of a car,as it present of front side ,beside this the bonnet is also crusical and critical component and needs to br designed in a way to provides protection for passengers inside car during…

under body coating:-       1) under body coating provides long term protection from corrosion to cars under body.        2) it also protects parts like internal body pannels frame rails and inner cavities that are not physically accessible but are prone to corrossion      …

BENCHMARKING: =>benchmarking is a process of comparing to compitators features,design,price  =>  it as important process of analysing similar products of dimensions,specification matrics => Benchmarking1 is a used to compare the cost,features =>Benchmarking2 is used for each and every component…