Week 9 - Attachment Feature Creation - Challenge 2

1. harness A & B defining given cad parts as electrically defined. with adding a connector connection point and the bundle connection point.   Check the bundle Continuity. Add snap of result in submission is used to analyze my connections are connected or not and to help to found my bundles and branches are…

DEFINE THE CONNECTORS IN ELECTRICA PART DESIGN. THEY CONNECTED EACH OTHER OR NOT   CONTINUITY CHECK FOR THE BUNDELS   CREATION  OF THE  HARNESS  WITH THE MULI BRANCHES AND CONNECTOR, PROTECTION COVERING FLATTENING PARAMETERS ADDED TO THE HARNESS ASSEMBLY AFTER FLATTENING  THE HARNESS

Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use Following connectors as shown in layout diagram.   creating sketch and added to the part design  w/b   Download connector 3D data from   DT06-4S DT06-6S DT06-2S DT06-08SA then creating…

V 16 ENGINE WIRING HARNESS  To design and develop the Wire Harness Routing for the given V16 Engine by following the design and packaging rules. OBJECTIVE:    To define all the connectors electrically and save it in the Catalogue. To place all the connectors and cavities at the required position. To place…

Aim: To route the wiring harness on the given tailgate assembly and prepare the flatten view and  drawing in CATIA V5.    door assembley     TO done a  routing for the given car door  DESIGN CRITERIA AND PACKAGING ASSUMPTIONS: Wiring harness routing shall provide ease in manufacturing,…

Q1. Download the following cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. P Clamp  Tree Structure creating points and planes In part design workbench   Switched to part design-  electrical part design. Define the support part in…

. Deutsch DT06– 08SA Open a file on the website and downloaded a file in isg format Opened in part design workbench To create a points and axis system. switch to electric part design the first step is to define the connector select  the connector in the w/b mention the type, name, and terminals   …

AIM :     To calculate the section modules of the hood design respectively.   PROCEDURE: y = distance between the neutral axis and the extreme end of the object Area moment of Inertia:The area moment of inertia of a beams cross sectional area measures the beam ability to resist bending.  The larger…

AIM :   To use the provided styling surface to come up with a back door design, use appropriate design methodologies, and provide the necessary reinforcements and embosses. Backdoor/Reardoor/Tailgate/Trunk:                  A Door is a hinged part which is used for entry…

                                                                            ROOF DESIGN    OBJECTIVE We need to design the…

AIM :       To assemble and apply gd&t to the butterfly valve assembly drawing.   ABOUT BUTTERFLY VALVE : Butterfly valves are quarter-turn valves that are popular for on-off or modulating services. They are lightweight, have a small installation footprint, lower cost, quick operation, and are available…

                                                                                           …

AIM :         To Calculate the Wheel Arch gap at required points and check whether the car passes the                  European standard.   ABOUT FENDER WHEEL ARCH:                    …

                                                       UNDERBODY COATING A car’s underbody is exposed to the most wear and tear caused by muddy water, potholed roads, stones…

THE ANSWER IS PROVIDED IN A PDF FORMAT. SO,KINDLY CHECK THE ATTACHED FILES .

                                                          HOOD DESIGN OF A CAR Aim:       To create and assemble the inner and outer panel of hood and…

                                        Project – Speed control of a DC Motor                                     …

AIM:   Read the voltage and current values from the given excel file and interpolate the values between -17.3:0.1:0.9.   STEPS TO FOLLOW:   To read the excel file in the matlab using xlsread function by creating variable m. Then to read the volatage v which isin coloumn 1 using v=m(:,1). Then to read…

switch bezel   tree structure     multi view   final draft analysis

core and cavity design tooling axis tree structure  Parting line  blue line is core  green line is a cavity  in the intersection, the part view is shown in the below picture is showing the mating of the core and cavity is a parting line after completing a closed surface shifted to parts design  and created a solid model …

door handle  draft analysis is not clear in this areas tree structure and explanation of sketchs finalize the surface are closed are not checked by boundary command shifted to (GSD) to the part design workbench  and created a part model by closed surface ccommand part model is created with the closed surface…

Door trim  Draft analysis for a given class a surface: Tooling axis creation is done by normal to the surface 2nd method    Class a draft analysis-3 degree :     Tree structure  class A, B, C, created it is a closed surface by final trim  GSD shifted to part design …

Door Trim Lower Plastic component   Creating the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.   …

a pillar  tooling axis  draft analysis with tooling axis tree structure:   closed surface created with class  a,b,c final class  draft analyses are done with the 2.9 degree. dog house  draft analysis .5 degree draft analysis are done given class a some areas are not clearing a draft analysis.…

  model -1   tree structure body 1  as per procedure referance are created and a reference axix are created, and then published to the plane and the axis are in the body, each and every body are created with the help of part model  now those part body are assembly in the help of assembly design …

1)Major elements in the above automotive wiring diagram are : ignition coil battery starter fuse ammeter current and voltage regulator generator gas tank unit dome light switch scaled beam parking lamp horn light switch 2)explaining three elements briefly: Battery : A battery is the collection of cells. Cell consist of…