For M35 Mix Design With Fly Ash      Aim : Mix design for M 35 grade…

AIM : To sketch a plan of G+1 floor residential building according to Vaastu Shastra and listing down the names of the structural drawings required to be provided to the construction site.   INTRODUCTION TO VAASTU SHASTRA :-   Vaastu Shastra :- Vastu Shastra is the Ancient Indian Science of architecture…

Aim: To draw residential building of dimensions 60’X20’ with following drawings Plot drawing Ground Floor Plan First Floor Plan Elevation Footing Layout Beam Layout Section View Introduction: The residential building to be drawn with plot dimensions 60’X20’.  The G+1 floor is designed…

Aim: To create: Template, inserting text and attributes Doors of warehouse and placing it in blocks Electrical legend and making it blocks Different types of door for residential project Drawing bars, making it as block and making it as a table as bar bending schedule.   Commands used:  Block. Insert. Attributes. Field.…

Aim: To Create the Kitchen Layout and to  Also, use proper dimension techniques to dimension the kitchen layout. Also, insert text wherever required. All dimensions are in mm. Procedure: step 1: units are set to mm limits and limax are also set  zoom comand is also used  hatch command fillet  command…

AIM: To create layout of the kitchen drawn in challenge 9 . Use A4 size page for the layout  and take a plot PROCEDURE: In the command prompt type ps and ms to adjust the view In the command prompt type pagesetup to make the size to A4 change  Click on the arrow mark to change the view    FINAl RESULTS:…

Aim:  To create a 3D model of the furniture element. Procedure: Step1: Open AutoCAD, select imperial as the units are in feet and inches.Go to units’ command and set it to engineering, so that feet inches can be inserted. Step 2: Create a box by clicking from the toolbar or box command, click on length,…

Aim: To draw the 3D Isometric View of the building as shown in the figure Introduction:   A plan view of wall of two elevation views of windows on both sides are given and they are to be converted into a 3D model. 2 window openings on both sides are given with details regarding the frame dimensions, mullion…

AIM:  To create a 3D rendered model for a Residential Building in AutoCAD INTRODUCTION: The main objective of this project is to understand about to create a Plan in 2D, then convert it into 3D using AutoCAD 3D, applying materials and rendering. AutoCAD is primarily used for generating 2D sketches. While it is…

    AIM:- To model a Ceiling from the architecture tab above the walls at the first-floor level.     INTRODUCTION:- The creation of Ceilings within Revit is a very similar process to that of Floors and Roofs- ie you can let Revit do most of the work and “guess” where…

1. From the above the options of type of structure to build a building,   I choose Multi-unit Residential Apartment.   2.  The geographical and location details for my project modelling, based on assumptions of Multi-unit Residential Apartment:- 1.    As above mentioned by the building comes…

Introduction: Dynamo is an open source visual programming language for Revit, written by designers and construction professionals. Its a programminglanguage that allows you to type lines of code;  while also creating an algorithm that consist of nodes. The user interface for dynamo is organized into five main areas,…

1.) PROCEDURE: First we have Open Revit file we want to export in Naviswork. In the file menu export to NWC format both Architecture and Structural File.             Once Exported Open Naviswork and open the Architectural File Cache in Naviswork.         RESULTS :…

1.a ) Observation :       In this picture we observe that, concrete get damage/ broken and reinforcement are visible at the bottom of beam.       The concrete spalled beyond the reinforcement that is indicates the segregation.       The top portion of beam is not exposed…

1.) Structural analysis is mainly concerned with finding out the behavior of a physical structure when subjected to force. This action can be in the form of load due to the weight of things such as people, furniture, wind, snow, etc. or some other kind of excitation such as an earthquake, shaking of the ground due…

AIM:- To compute Ln , Mn and Γn for each of the five modes from the given equations.            To calculate the effective modal mass Mn* and the modal mass participating ratio for the 5 modes.            To obtain the base shear…

1.)Symmetry :- Having a look over the aspects of symmetry of the framing plan, it is observed that the distribution of mass, Stiffness is across the plan it is observed that the distribution of mass, stiffness is across the plan. It is considered for one of the good Symmetrical aspects .This tends to reduce the horizontal…

1.) STRCTURE (a)For this structure is considered as it is asymmetric in nature.There is some uncertainty concerning certain features of the seismic response of non-rectangular walls.It occurs lack of tensile capacity and force configuration.These walls have high stiffness and strength in both direction,They are subjected…

Aim: to model and analyse a 25 storey building with given specifications and to cross check the parameters as per IS 1893 provisions.Introduction: ETABS offers is the recognition of story levels, allowing for the input of building data in a logical and convenient manner. You can define your models on a floor-by-floor,…

AIM: TO MODEL AND ANALYZE MULTIPLE BUILDINGS WITH DIFFERENT FLOOR LEVELS AND DESIGN PARAMETERS USING ETABS SOFTWARE AND COMPARE THE RESULTS TO UNDERSTAND THEIR OVERALL SEISMIC BEHAVIOUR.INTRODUCTION: The structural configuration of the building plays a major role in determining the overall response during an earthquake.…

Aim:- To design the beams in detail from the ETABS 2019.            To provide details of longitudinal and shear reinforcement for the given two continuous beams.            To calculate the value of maximum shear force in any one of the spans in the continuous…

Aim: To Providing details of longitudinal reinforcement for the two columns from foundation to terrace level.Step 1:1) Open a G+4 ETABS file2) Run Analysis3) Click the Concrete Frame Design tool4) Select the Display Design Info option5) Choose design output as Longitudinal ReinforcementStep 2:1) After Selecting the…

Given Data :Column Size: (400x400)mmCompression axial load for the load combination of (1.5 DL + 1.5 LL) : 2000 KNSafe soil bearing capacity at a depth of 2 meters below E.G.L is 150 kN/m²Grade of concrete(M25)= 25 kN/m²Assuming fy =415 N/mm²Assuming the self-weight of the footing and soil above it as a 10% loadCalculations:1.)…

AIM: To Analyze and design the isolated footing from week 11 challenge on SAFE to verify the size, depth and steel provided as per calculations.PROCEDURE:STEP: 1 Open the SAFE Application select New Model followed by Input Settings, Units was selected as Metric and Code IS 456-2000.STEP: 2  Safe…

AIM:-To Create and analyse the given building in ETABS 2018, the structural model has to be prepared in accordance with IS 1893 and as per IS 13920. To design the pile cap and pile reinforcement details, Tie  beam  connecting the pile caps, to sketch the column reinforcements, to produce the framing plan and…

1.1 Open the STAAD pro software and locate the share option available on the introduction screen.After clicking on the share button, select send mail option.Then, browse for the .Std file on your machine & send it.1.2 Different materials that can be designed using STAAD Pro. are as below;Concrete.Steel.Aluminium.Timber.Composite…

1.Step-1i) Create the model in the STAAD Pro ii) Draw the Nodes at ( 0 ,0 , 0) and ( 0 , 10, 0) as shown below iii) Join this nodes by using Add beam optionsStep-2i) Now Click on Properties.ii) Select Define parameters as circular column of 0.5m radius.iii) Assign the Circular shape of the column ( 0.6 m radius) 1.2i)…

AIM : Design a multi storey residential building located in Bangalore using STADD Pro Connect EditionPROCEDURE :Open the Staad.Pro software and save the project by giving the appropriate file nameGo to geometry tab and create a nodeSelect Translational repeat command and give the nodes in x , y and z directions as…