SECTION A  1 Objective:-  Make a Simulink model of Doorbell using a solenoid block with the following details:                  In the above arrangement, when the switch is closed the electromagnet receives electrical power from the battery and…

AIM Implement control logic of a “washing machine” using Stateflow as per given sequence:  If the power supply is available, the system gets activated  If the Water supply is not available, stop the process & indicate through LED Soaking time should be 200s followed by Washing time of 100s. Then…

Use ADVISOR tool and simulate the following     For EV_defaults_in file, if cargo mass is 500 kg with all other default conditions, can the vehicle travel for 45 km with FTP drive cycle? Conclude your observations.    In the above case, try changing the battery capacity and repeat the simulation.…

Question What is the difference between mapped and dynamic model of engine, motor and generator? How can you change model type?  How does the model calculate miles per gallon? Which factors are considered to model fuel flow?  Run the HEV ReferenceApplication with WOT drive cycle. Change the grade and wind velocity in the…

Question Which types of power converter circuits are employed in electric and hybrid electric vehicle?    An Electric Vehicle's powertrain with 72V battery pack in shown in the diagram below. The duty ratio for acceleration operation is 'd1' and for the braking operation the duty ratio is 'd2'.    …

                                                                                                                                              Your Answers AIM:-   1. A. Explain a MATLAB demo model named ‘Speed control of a DC motor using BJT H-bridge’.     B. Comment on the armature current shoot-up from the scope results.…

                                                                              Powertrain for aircraft in runway. Question:-…

                                                                  ANSWER (WEEK 11).   For a defined driving cycle, calculate the energy required…

                                                                               Final Project On Design Of An Electric Vehicle With Matlab-Simulink. Create a MATLAB model of electric car which uses a battery and a DC motor. Choose suitable blocks from Powertrain block set. Prepare a report about your model including following:…

                                                                                           …

                                                          Project 2 Adaptive Cruise Control (ACC). General Overview: Adaptive Cruise Control Feature for passenger cars allows…

                                  Week 1 Understanding Different Battery Chemistry QUESTION; 1.Prepare a table which includes materials & chemical reactions occurring at the anode and cathode of LCO, LMO, NCA, NMC, LFP and LTO type of lithium ion cells.Give your detailed explanation on it 2.Compare the differences between…

                                                      Final Project: Electric Rickshaw modelling QUESTION Create a detailed MATLAB model of an electric rickshaw (three wheel passenger…

                                                                              Project-1: Modelling an electric Car with Li-ion battery QUESTION: Create a MATLAB model of electric car which uses lithium ion battery and suitable motor. Choose suitable blocks from Simscape or Powertrain block set. Implement the vehicle speed…

Aim: To prepare a technical report of Simulation of BAJA All-Terrain Vehicle (ATV) under different conditions Objectives: Carry out a system-level simulation of an all-terrain vehicle and prepare a technical report explaining the model properties & comments on the results. ALL-TERRAIN VEHICLE: An all-terrain vehicle (ATV)…

                                                                                Week 7 State of charge estimation QUESTION 1.Simulate the 3 test cases from harness dashboard and write a detailed report on the results 2.What is coulomb counting? Refer to the above model and explain how BMS implements coulomb counting for…

                                                         Project 1 :- Mechanical design of battery pack. QUESTION: Battery pack capacity: 18 kWh Cell: ANR26650M1-B  Prepare a detailed battery pack drawing along with its enclosure. State your assumptions. ANSWER: Details of Cell: ANR26650M1-B:                          …

                                                  Project 2 Thermal modeling of battery pack QUESTION: For a 10 cell series lithium ion battery model, simulate the thermal effects and compare…

                                           Project 1- Traffic Jam Assistant Feature Traffic Jam Assistant Feature Introduction to the Feature: Traffic Jam Assistant is one of the most common feature in Advanced…

                                                             Week 2 Session 7 Compare the different architectures of HEV. Discuss the pro's and con's Architecture of…

                                                             Week 3 Session 7 Compare the different motors used in EV and list down the advantages and disadvantages…

                                                                                Week 4 Session 5 QUESTION- Explain…

                             Project 2-Highway Assistant-Lane Changing Assistant QUESTION- Introduction to the Feature: The Highway Assistant supports the driver and takes over the longitudinal and lateral guidance of the vehicle in monotonous driving…