Nirmal Alexis Robert Raj
Mechanical Engineer | R&D | CAE | Tooling Design |
Skills Acquired at Skill-Lync :
- HYPER-MESH
- STRUCTURAL-MESHING
- SHEET-METAL-MESHING
- FEA
- LS-DYNA
Introduction
18 Projects
Week 4- Challenge
Report 3 Objective: The aim of this report is used to create the various 1D elements such as Rod, beam, and…
30 Oct 2020 06:22 AM IST
Week 6- Challenge
…
31 Dec 2020 03:45 PM IST
Week 8-3D Tetra Meshing Challenge
…
09 Feb 2021 11:35 AM IST
Week 9-Creation of 1D Connectors Challenge
…
17 Feb 2021 09:51 AM IST
Week 12:Project-1-Meshing of Door Inner Panel Challenge
…
16 Mar 2021 01:40 PM IST
Week 12:Project 2-Meshing of Rear Wheel Holder challenge
Project 2 - Meshing of a Rear-Wheel holder OBJECTIVE The aim of this project is to generate…
16 Mar 2021 01:47 PM IST
Week - 1 - Consistency of Units
OBJECTIVE: Value of the following measurements are given as follows: MASS 1kg LENGTH 1m TIME 1s FORCE 1N STRESS 1Pa ENERGY 1Nm DENSITY 1Kg/m3 YOUNG'S Modulus 210GPa Velocity 56.33KMPH GRAVITY 9.8m/s2 Converted Measurements: MASS 1kg = 1000 g LENGTH 1m = 1000 mm TIME 1s =1000 ms FORCE 1N = 1kg * 1m/s^2 = 1000*1000…
20 Apr 2021 09:20 AM IST
Week - 2 - Explicit and Implicit Analysis
Here is my week 2 report
27 Apr 2021 12:43 PM IST
Week - 3 Drop test Challenge
Here is my week 3 report.
03 May 2021 08:36 AM IST
Week - 4 - Crash Box Simulation
REPORT 4 AIM: To simulate the crash test for a crash box having a different…
21 May 2021 02:13 PM IST
Week - 5 - Modelling Spotwelds
REPORT 5 AIM To model spot welds using beam and solid elements separately in a systematic manner for the given assembly of parts and to run a crash test to required output data given below. INPUT 3-7 spots welds should be used along the line specified in…
26 May 2021 10:55 AM IST
Week-6 Calculate the Stretch Ratio by comparing the ELFORM (-2,-1,1,2) with Ogden_Material Model.
WEEK-6 AIM To create a block of 10*10*10 mm dimensions of elements in each direction…
02 Jun 2021 07:29 AM IST
Week-7 Head Impact
WEEK -7 PEDESTRIAN HEAD IMPACT CHALLENGE AIM : To simulate a pedestrian head impact test on the given models which are provided for three different cases scenarios and to get the required output data given below for three different cases. OUTPUT DATA: The impact simulation…
14 Jun 2021 11:04 AM IST
Week - 8 Mass Scaling
REPORT - 9 ( MASS SCALING) AIM To reduce the run time of the model and to increase the stability…
21 Jun 2021 06:34 AM IST
Week - 9 Material Modeling from Raw Data
week-9 (Material modeling from Raw data) AIM To do material modeling for the given true stress-strain curve of graphite iron casting, by using the given material card MAT-24 and then validate the simulated material model data with the experimental material model raw data.…
15 Jul 2021 07:11 AM IST
Bird Strike - Project - 2
WEEK 12: OBJECTIVE: To perform a bird strike simulation in LS-DYNA and evaluate the results. PROCEDURE: The project file contains hub, blade, engine casing, and bird geometry. The blade rotates at a constant velocity and the engine casing should remain stationary. The cylindrical bird travels along its own axis toward…
29 Jul 2021 04:33 PM IST
2 Course Certificates
HyperMesh for FEA Plastic and Sheet Metal Applications
Academic Qualification
12th
Vilnius Gediminas Technical University (VILNIUS TECH)
04 Oct 2017 - 20 Jun 2019
Masters of Science in Engineering
Vilnius Gediminas Technical University (VILNIUS TECH)
07 Oct 2017 - 07 Jun 2019
B.E
LICET : Loyola-ICAM College of Engineering and Technology
01 Aug 2012 - 07 May 2016
10th
Cluny School
07 Jul 1998 - 30 Apr 2010
Here are the courses that I have enrolled
Similar Profiles
Ladder of success cannot be climbed with hands in pocket.
The Future in Motion
Give more than what you get you will get more than what you gave
Avid learner