Design, Assembly and Rendering of American Chopper Bike    Objective:            …

                                                            Design, Assembly and Rendering of the Yacht   Objective:              …

                                                                                 UnderBody Coating Introduction  …

                                                                                           …

                                                                                  CAR HOOD DESIGN   Aim: …

                                                                           Wheel Arch Gap Calculation Aim:       …

                                                                                  Fender Design Objective:    …

                                                                                SECTION MODULUS OF THE HOOD Objective: …

                                                                      ROOF DESIGN OBJECTIVE : The objective of this project is to design car…

                                                                       BACK DOOR DESIGN OBJECTIVE : The main objective of this project is to…

Objective:                 The main objective of this challenge is to create the Base Bracket Plastic component through the above-given Class-A surface, by giving the 'Tooling axis' and 'Draft analysis' to the class-A surface of the base bracket. TOOLING AXIS:      …

Objective:                 The main objective of this challenge is to create the Switch Bezel Plastic component through the above-given Class-A surface, by giving the 'Tooling axis' and 'Draft analysis' to the Switch Bezel.            …

Objective:                 The main objective of this challenge is to create the Coin Holder Design Plastic component through the above-given Class-A surface, by giving the 'Tooling axis' and 'Draft analysis' to the Coin Holder.          …

Objective:                 The main objective of this challenge is to create the Bumper Design Plastic component through the above-given Class-A surface, by giving the 'Tooling axis' and 'Draft analysis' to the Bumper.            …

                                                           Core and Cavity Design Objective:                 The main objective of…

                                                                 Ribs and Screw Boss creation    Aim :    To create the Rib for the drill…

AIM Create the Dog House for the Door Trim considering the design rules   INTRODUCTION DOG HOUSE Dog house is an engineering feature used in plastic design. Dog houses are used as support feature. Sometimes other engineering features like snaps, locators, screw bosses are mounted on them to increase their strength.…

                                                  DOOR TRIM LOWER HEAT STAKE AND LOCATORS Aim: To Create the Door trim lower component through the given Class-A surface. Objectives: • Creation…

                                         DESIGNING A PILLAR USING MASTER SECTION OBJECTIVES To improvise the Class A surface by resolving bad patches and adding flanges to it.  To create A pillar solid model with…

AIM : To create part models and assemble the components using the 2D drawings which were provided.   OBJECTIVE : To create the various part models from the 2D drawings. To asseble the part models into a single component. To create the 2D drawings of the components which were created.   QUICK RETURN MECHANISM…

AIM To create a door interior part from the inputs of class A surface along with master section by following the design rules followed in tier 1 and OEM industries in catia v5 SOFTWARE USED CATIA V5 OBJECTIVES Create a sketch by using Positioned sketch All the should be sketches should be Iso-Constrained Ensured Proper…

        CONNECTOR DEFINATIONS IN CATIA V5 1. Deutsch DT06 – 08SA Connector connection point:                     Craete Axis System with respect to the point which we have created and defining the axis direction as shown below,  …

Hellarmann Tyton – 21160129 process: Create two points one as entry and another as exit point. create planes at two points and another at base. Switch to Electric part desgn Click on support defination - select part - select entry point - select entry plane, exit and base plane. Again Click on support defination…

Aim:  1) To Route the following harness layout in the Electrical workbench. 2) Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Given: CAD data of the following Connectors:  DT06-4S DT06-6S DT06-2S DT06-08SA DT06-4S                …

Aim: Route two electrical harnesses per the given layout and interconnect them as a single harness assembly check for bundle continuity, and bundle warnings, and then provide annotations for the final harness assembly. Objective: The objective of this project is to first route the two Harness A and Harness B as per the…

AIM: TO FLATTEN THE WIRING HARNESS AND DRAFT THE WIRING HARNESS ASSEMBLY. GIVEN SKETCH:                       HARNESS ASSEMBLY:                      HARNESS FLATTENING: WE GO TO THE HARNESS FLATTENING WORKBENCH…

                                                                   V16 ENGINE PHASE WIRING HARNESS Aim-          To Route the…

Aim: Route the Wiring Harness on given Car body and prepare flatten view drawing in Catia V5 Objective:                The objective of this project is to route the wiring harness and prepare flatten view drawing for the tailgate of the car. All types of packaging rules have to be considered while routing the harness and…

1.What is BIW & define its parts? Body in white (BIW) refers to the stage in the automobile manufacturing in which a car body’s components have been joined together, using one or a combination of different techniques: welding (spot, MIG/MAG), riveting, clinching, bonding, laser brazing etc. Body in White, or…

1. What is process of project execution activity? Answer: Project activities are those basically are being processed or being practiced in general project of BIW begins. Project activities are task from start to end of project. There are various step involved in project. Below fig. show flow chart of project activities.…