1. Working Of A Electric Doorbell:- >Electric bell is based on the principle of electromagnets. When switch is pressed, electromagnet is activated and the hammer moves and hits the gong. As the hammer moves, circuit breaks and the electromagnet is disabled. This causes the hammer to go back to initial position…

1. Control Logic Of a Washing Machine:- >In this system(washing machine), a couple of inputs are taken in cosideration for the chart of stateflow "power supply" and "water supply". >The outputs taken in cosideration for chart are water, soaking, rinsing, dryer, end. >To run this system we have to select and…

>Introduction:- >An all-terain vehicle(ATV), also known as a quad(cycle), three-wheeler, four-track, four-wheeler or quadri-cycle as defined the American Ntional Standard Institute(ANSI) is vehicle that travells on low pressure tires, with a seat that is stradeled by the operator, along with handle bars for steering…

EV-BAtch 16 Student:- (1)Difference between mapped and dynamic model of engine, motor and generator: The Mapped Model: >The simulation of powertrain blockset consists of data that is pre-built in the look up table is dealing with mapped data or mapped model. >The map model calculaton is much fast. The Dynamic Model:…

(1)Types of power converter circuits employed in electric and hybrid electric vehicle:- >A motor drive consists of a power converter and a controller. A power electronic convereter handles the flow from the bulk from the source to the motor input terminals.The controller process the command input and the feedback information…

(1) For EV_defaults_in file, if cargo mass is 500 kg with all other default conditions, can the vehicle travel for 45 km with FTP drive cycle? >Load the advisor tool in the matlab command window and than select the ev_dwefault_file in the load file section, change the cargo mass to 500kgs, other than that keep…

Student of EV Batch-16: 1(A)MATLAB demo model named ‘Speed control of a DC motor using BJT H-bridge’.   >Bipolar Junction Transistor(BJT) when used for power switching applications, operates as an IGBT. When it is conducting,a forward voltage Vf is developed between collector and emitter(in the range…

Student of EV Batch 16: 1.For a defined driving cycle, calculate the energy required for braking: >The driving cycle taken into conisideration is UDDS cycle which stands for Urban Dynamometer Driving Schedule. >The data is taken for a total driving time for 1370s. >The command script for the energy is given below:…

Student Of Online Ev BAtch 16: PART-A 1.List out the total weight of various types of aircrafts: There are many factors that lead to efficient and safe operation of aircraft. Among these vital factors are proper weights and balance control The maximum allowable weight for an aircraft is determined by design considerations.…

Student of Online EV-Batch 16:- PURPOSE OF MATHEMATICAL MODEL & SIMULATION >Mathecmatial models are most suitable for initial experiments. >Actual system relaiasation is costly and time consuming. >Testing before actual demonstration. >We know before to see the limitations and failures and knowing errors…

(1). Student Of EV Online BAtch 16 Construction And Working of Li-ion battery: >A li-ion battery is said to be a collection of several li-ion cells in series and parellel connection. >The anode of the battery has the negative terminal, while cathode carrys positive terminal. >Seprator plates are used in between…

(1). Stimulate 3 cases for harness dashboard: >The battery model harness dashboard is represented below:   Case 1:     >Click on the test sequence varient block and select test case as 1. >By clicking on the BMS Sequence block we get the chart. >When simulation will start, the model will be in…

AIM: > To prepare a detailed battery pack drawing along with its enclosure & state the assumptions taken. Cell: ANR26650M1-B >This is a nanophosphate high power lithium ion cell.   >A123's high performance Nanophosphate lithium ion phosphate (LiFeO4) battery technology delivers high power and energy…

Introduction: >The lithium-ion battries are widely used as energy sources in different hybrid and electric vehicle, however the operation characterstics of the battery in such vehicle are strongly dependent on the operation temprature and therefore, with purpose to improve these characteristics as a godd thermal control…

Aim: >To identify the direction of the vehicle based on the camera input. Objective: >Development of MATLAB Simulink model as per requirement. >Tag the requirements to the simulink model; tagging requiremnet 1 and requirement 2 to the their corressponding subsytems is fine. >MBD complaint chnages, Data Dictionary…

Aim: >To build a simulink model as per tghe requirements given and also to show requirment tagging in the model. >To check the model undefr standard guidline(MAB Guidelines) with help of model advisor. >To build an embedded C-Code for the model. Objective: >Developing Adaptive Cruise Control feature as per…