American Chopper Objective:-  The objective of this project is used to create a model of different parts of the chopper using Solidworks. To assemble the different parts model for the chopper. To create a photorealistic model of the chopper and Render the model using Solidworks Photoview 360 or Solidwork Visualize. Software…

                                                                     MODELLING AND ASSEMBLING OF YACHT Objective: To Design all parts of the yacht…

What is Benchmarking process ? Benchmarking is the process of comparing the exsiting product,Its services, quality of the product, cost of product and process of the product, etc.f For the betterment of the product quality availability of the product in future  This process is using in every industries for the create a…

What is Under-body coating? Underbody coating is a thick resilient coating applied to the underbody or chassis of an automobile to protect against impact damage from small stones, which would rapidly chip ordinary paint, allowing rusting to begin. No matter the climate, the underbelly of every vehicle needs proper…

HOOD DESIGN OBJECTIVE     Design outer panel with the hem, develop the Inner Panel, develop all the necessary Reinforcements, Mirror and position the Hinge & Striker, provide Mastic Data, and provide the required Emboss definition. With this understanding, an industry-standard hood panel is to be designed which can very…

Aim: Calculate the Wheel Arch gap at required points and check whether the car passes the European standard. Objective: Create the detum plane on outer face of the wheel. Draw the sketch by help of European regulation. Measure the distance between wheel outer face point and fender arc. Tabulate the result…

                                                                              FENDER DESIGN Objective:     The main…

Section Modulus calculation and optimization Aim:-       To calculate the section modulus by using the section of Hood desgin and then optimizing the hood panel for better section modulus. Section modulus: Section Modulus is the geometric property of the given cross-section of any shaft or beam structures. It is the direct…

OBJECTIVE:  To develop the essential flanges and reinforcements with appropriate dimensions and checking draft by performing Draft analysis, Calculating Section inertia, Heat distortion and Snow load on the roof.  A dumb solid body of roof CAD model is provided for which following points to be designed and analyzed…

                                                                           Assembly of Back Door and/ Tailgates Aim:    …

Week 8 - Challenge 1 - Base Bracket Design AIM :- The main objective of this challenge is to create the Base Bracket Plastic component through the above-given Class-A surface, by giving the 'Tooling axis' and 'Draft analysis' to the class-A surface of the base bracket. Index of tooling axis Check the connectivity…

Week 8 - Challenge 2 - Switch Bezel Design AIM :-  To create the Switch Bezel plastic component through the given class A surface and create the required Tooling axis and perform the Draft analysis on the model. INTRODUTION The control panel bezel is the frame part of the window switch that holds its switch covers…

Week 8 - Challenge 3 - Coin Holder Design Aim -  Create the Coin Holder Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  ABOUT…

Week 8 - Challenge 4 - Bumper AIM: To make a model from the provided class-A surface. OBJECTIVE: To create a tooling direction. To perform draft analysis for given A-Surface and prepare the final close body. To design the Bumper plastic component by creating the B-Surface and C-Surface using the given Class-A surface.…

Week 8 - Challenge 6 - Core & Cavity Design AIM : Create the Core and cavity blocks for the switch bezel designed in the earlier challenge.  CREATION OF TOOLING AXIS :  Considering the Ejection from the cavity of the mould after manufacturing the interior trim (switch bezel) must have the nominal 3-degree draft angle.…

Week 9 - Attachment Feature Creation (Ribs & Screw Boss) - Challenge 1 DOOR HANDLE : AIM : Create Rib and Screw boss for the door handle considering design rules. Objective : Create the Tooling axis by using the bisecting method. Design the class-B and class-C surfaces and join them. Create the solid feature by…

Week 9 - Attachment Feature Creation - Challenge 2 AIM: To Create theDoor Trim Component from the given Class-A surface. To Create the Tooling axis for the given Class-A Surface meeting the requirements of the draft angle. To perform the Draft analysis on the model.  To Create the B Side Feature in the component by…