UNDERBODY COATING The underbody coating is process in which involves the thick resilient coating applied to the underbody or chassis of an automobile to protect against impact damage from small stones, which would rapidly chip ordinary paint,then allowing rusting to easly. Purpose of under body coating Mainly protects…

BENCHMARKING: In the automobile industry involves a structured comparision between similar products,services, or processes on same dimensions of performance. The point of benchmarking is to identify internal opportunities for improvement. Process of benchmarking this kind can operate at several levels: Between similar…

Objective To understand the design strategy and consideration that goes under designing and developing an automotive hood to achieve maximum safety for all condition. With this understanding, an OEM-standards hood panel is to be designed which can very well be manufactured and assembled. In other words, the design has…

AIM: By using the skin data develope the fender as per master section. Objective : 1.Intruduction to Fender.                   2.Fender types.                   3.Fender design.                …

Aim: To calculate the section modulus by using the hood design.   Objective: 1.Description.                  2.Elastic section modulus.                  3.Plastic section modulus.          …

AIM : To design and develop car roof by given roof styling,master sections. Calculate the Bow-roof position by making roof curvature study. OBJECTIVE: Introduction To develop the all componets by using styling & Master section. To calculate the Bow-roof position by making roof curvature study. To calculate the heat…

CAR BACK DOOR(TAIL GATE) DESIGN AND DEVELOPMENT PROCESS.   AIM: To Design a back door of a car using of class "A" surface. Abstract : A backdoor of a car also known as tail gate is a commodity which normally serves the purpose of covering the car from the rear end. But there are more function that come with it…

AIM : To create the Base Bracket Plastic component through the given Class-A surface.   Objective :- To create a tooling direction. To perform draft analysis of the plastic component. To design the base bracket plastic component by creating the B-Surface and C-Surface using the given Class-A surface. Class A Surface…

AIM : To create the Switch Bezel Plastic component through the given Class-A surface. Objective :- To create a tooling direction.To perform draft analysis of the plastic component.To design the base bracket plastic component by creating the B-Surface and C-Surface using the given Class-A surface. Class A Surface : Check…

AIM : To create the Coin Holder Design Plastic component through the given Class-A surface.   Objective To create a tooling direction. To perform draft analysis for the A-Surface and final close body. To design the base bracket plastic component by creating the B-Surface and C-Surface using the given Class-A…

AIM : To create the Bumper Design Plastic component through the given Class-A surface.   Objective To create a tooling direction. To perform draft analysis for given A-Surface and prepare the final close body. To design the Bumper plastic component by creating the B-Surface and C-Surface using the given Class-A surface.…

AIM: To Create the Core and cavity blocks for the switch bezel component.   Objective While Preparing the core and Cavity is mainly dends on Plastic componet and Tooling Direction. Basicaly set up Core and Cavity depends up on the Part size. Also moment (or) Direction follows the Tooling Direction. 1) Tooling…

AIM: To create the DOOR HANDLE Design Plastic component through the given Class-A surface. With Attachment Feature Creation Rib and Screw boss.   Objective To create a tooling direction. To perform draft analysis for given A-Surface and prepare the final close body. To design the Bumper plastic component…

AIM: To create the Door Trim Design Plastic component through the given Class-A surface. With Attachment Feature Dog house. Objective To create a tooling direction. To perform draft analysis for given A-Surface and prepare the final close body. To design the Bumper plastic component by creating the B-Surface…

AIM : To create the Door Trim Lower Design Plastic component through the given Class-A surface. Also create the engineeing features as 4way locaters and heat stakes.   Objective To create a tooling direction. To perform draft analysis for given A-Surface and prepare the final close body. To design the Bumper…

AIM : To create the A pillar Design with Master Section and using through the given Class-A surface. Also create the engineeing features as Dog house. Objective To create a tooling direction. To perform draft analysis for given A-Surface and prepare the final close body. To design the A pillar plastic component by…

AIM : Create the Assembly of given 2 Mechanisums. Observation : First create all parts in Part work bench then take the all part in assembly then make constrain them. Once make constrain then check it with Explode view where all parts are constrains properly. Below Snaps are shown the preparation of assembly. 1.QUICK…

 AIM:- To create a solid body of Side Door plastic trim including the engineering features using CATIA V5 tool using the  given Class A surface and master section and adding thickness to the component. INTRODUCTION:- Side Door Plastic Trim An interior plastic component attached to the inner side of the door. This product…

Title of the Project: Advanced Sheet Metal Design Using NX Cad Challenge 1 Casing Design Objective: To design a Casing with the help of NX advance sheet metal. Introduction: NX Sheet Metal provides a set of tools within the NX design environment that allows for simple and fast design of sheet metal parts, dependent on…

1.Title of the Project : Box Assembly   2.Objective : The objective of the project is to design a Box Assembly using sheet metal application in Siemens NX software.   3.Introduction : Sheet metal is metal formed by an industrial process into thin, flat pieces. Sheet metal is one of the fundamental…

Title of the Project : To advanced Sheet Metal Design Using NX Cad Odd Shaped Enclosure. Objective :To design an odd shaped enclosure and create a draft of it using Siemens NX Sheet metal application. NTRODUCTION :      Sheet metal is metal formed by an industrial process into thin, flat pieces. Sheet…

Title of the project : Advanced Sheet Metal Design Using NX Cad Challenge_6_Bracket. OBJECTIVE : Modelling a Sheet Metal Bracket using NX CAD. Write a detailed report on Sheet Metal Component with good explanation on Sheet Metal modelling tools applied throughout the modelling. Also attach the Final model Images…